lkml.org 
[lkml]   [2015]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
SubjectRe: [Patch-V2 1/6] INPUT: xpad: Add minimal support for Logitech G920 Wheel
From
On Thu, Dec 10, 2015 at 6:08 PM, Benjamin Tissoires
<benjamin.tissoires@redhat.com> wrote:
> On Dec 09 2015 or thereabouts, Dmitry Torokhov wrote:
>> On Wed, Dec 9, 2015 at 5:23 PM, Dmitry Torokhov
>> <dmitry.torokhov@gmail.com> wrote:
>> > On Thu, Nov 19, 2015 at 10:31 AM, Dmitry Torokhov
>> > <dmitry.torokhov@gmail.com> wrote:
>> >> On Thu, Nov 19, 2015 at 02:50:51PM +0100, Jiri Kosina wrote:
>> >>> On Thu, 12 Nov 2015, Simon Wood wrote:
>> >>>
>> >>> > When plugged in the Logitech G920 wheel starts with USBID 046d:c261
>> >>> > and behaviors as a vendor specific class. If a 'magic' byte sequence
>> >>> > is sent the wheel will detach and reconnect as a HID device with the
>> >>> > USBID 046d:c262.
>> >>> >
>> >>> > Signed-off-by: Simon Wood <simon@mungewell.org>
>> >>>
>> >>> Adding Dmitry to CC.
>> >>>
>> >>> Dmitry, I am planning to take this through my tree together with the rest
>> >>> of the actual HID support for that device if you Ack this.
>> >>
>> >> Hmm, I have an incoming series for xbox that night clash with this... If
>> >> you'll put it in a clean branch off 4.3 I'd pull it and then get more
>> >> changes on top.
>> >>
>> >> Can we also change the subject as it is not about adding a minimal
>> >> support. Something like "Input: xpad - switch Logitech G920 Wheel into
>> >> HID mode"
>> >>
>> >> Otherwise:
>> >>
>> >> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
>> >
>> > Hmm, looking sat this some more why are we waiting to switch device
>> > mode until after userspace opens input device instead of when we are
>> > executing driver probe()?
>> >
>>
>> Actually, thinking about it even more, why do we want to have this in
>> xpad.c? Have HID module handle both IDs and switch to HID mode if we
>> want HID to handle this device. I think we should revert/drop this
>> patch.
>>
>
> Hi Dmitry,
>
> IIRC, last time I saw an XBox-like controller, it doesn't register as a
> HID device at all. SO I think It will be hard to switch it into the HID
> mode from HID directly.
> Simon, can you confirm that the device does not contains any references
> to HID while in the XBox mode (lsusb -v should give enough information).

This is probably not relevant anymore, but here is the "sudo lsusb -v"
output of my G920 in XBox mode:

Bus 001 Device 121: ID 046d:c261 Logitech, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 255 Vendor Specific Class
bDeviceSubClass 255 Vendor Specific Subclass
bDeviceProtocol 255 Vendor Specific Protocol
bMaxPacketSize0 64
idVendor 0x046d Logitech, Inc.
idProduct 0xc261
bcdDevice 96.01
iManufacturer 1 Logitech
iProduct 2 G920 Driving Force Racing Wheel for Xbox One
iSerial 3 000072fb6b3b9f58
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 71
bInterfaceProtocol 208
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 4
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 4
Device Status: 0x0002
(Bus Powered)
Remote Wakeup Enabled


\
 
 \ /
  Last update: 2015-12-13 14:21    [W:0.271 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site