lkml.org 
[lkml]   [2015]   [Nov]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 22/26] Input: synaptics-rmi4 - Add F30 support
From
Date
On 11/09/2015 06:06 AM, Benjamin Tissoires wrote:
> Hey Linus,
>
> first thanks for the reviews. Much appreciated.
>
> On Mon, Nov 9, 2015 at 2:32 PM, Linus Walleij <linus.walleij@linaro.org> wrote:
>> On Fri, Nov 6, 2015 at 12:42 AM, Andrew Duggan <aduggan@synaptics.com> wrote:
>>
>>> From: Benjamin Tissoires <benjamin.tissoires@redhat.com>
>>>
>>> RMI4 Function 0x30 provides support for GPIOs, LEDs and mechanical
>>> buttons. In particular, the mechanical button support is used in
>>> an increasing number of touchpads.
>>>
>>> [BT] cured the code to rely only on the unified input node created
>>> by rmi_driver.
>>>
>>> Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
>>> Signed-off-by: Allie Xiong <axiong@synaptics.com>
>>> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
>> I see this function driver is not yet adding any gpio_chip or
>> LEDs class devices, which is fine, we can add that later when
>> we have something to test. Or is iit using that LED feature
>> in the input layer that corresponds to caps lock etc?

F30 is currently only used in touchpads and mostly used to report the
the click of the tact switch on clickpads. When the GPIO interrupts we
report the appropriate button event to the host. Because the GPIOs are
wired to our ASIC and not to the host I'm not sure there is any benefit
to exposing it to the host using gpio_chip.

Dmitry asked a similar question and here is my response to him:
http://www.spinics.net/lists/linux-input/msg40458.html

There are a few rmi touchpads which have LEDs in the top left corner to
indicate if the touchpad has been enabled / disabled. Writing to a
register in F30 would turn on and off the LED. I don't think they are
being made anymore so I haven't really looked into how we would
implement this. If there is something in the input layer for controlling
LEDs that might be the way to do it.

> Do not take my words as the official ones, but when we discussed with
> Synaptics about F30 (and unified input), they told us that they
> designed the driver based on the phone use case. In such use case, the
> power (and maybe LEDs) are handled through F30, and the touchscreen
> through F11/12. Problem is, I am not even sure there are phones around
> with such F30/F11 combination.
>
> So in the end, from what I can see, F30 is used for buttons on
> touchpads/clickpads, and LEDs when there are some on these touchpads.
>
> I don't know if the keyboards would use F30 for their LEDs though.
>
> That being said. Unless Synaptics tells us that there are uses of a
> non "unified" input device somewhere, I would also agree to only keep
> the "unified" input node, which would simplify both F11/12 and F30.

The original architecture of the driver was to have each function have
it's own input device. The reasoning was that you would have a phone
with a touchscreen (F11) and maybe some capacitive buttons (F19 or F1A
or something) and that the system should see these as two separate
devices. I'm wondering if this is needed though. Would userspace care if
a touchscreen also reported KEY_HOME, KEY_BACK, or KEY_MENU?

At this point I agree, it's probably time to just have F11, F12, and F30
all report from the input device created in rmi_driver and remove the
non unified option. If someday there is a function which needs to report
data from a different input device it can just create it in that function.

Andrew

>> I don't quite get it I guess :/
>>
>> But I guess it should also be squashed into the original F30 driver.
> I think this is the original F30 driver :-)
>
> Cheers,
> Benjamin



\
 
 \ /
  Last update: 2015-11-10 00:21    [W:0.073 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site