lkml.org 
[lkml]   [2015]   [Nov]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v9 1/5] Documentation: add sbsa-gwdt driver documentation
Date
From: Fu Wei <fu.wei@linaro.org>

The sbsa-gwdt.txt documentation in devicetree/bindings/watchdog is for
introducing SBSA(Server Base System Architecture) Generic Watchdog
device node info into FDT.

Also add sbsa-gwdt introduction in watchdog-parameters.txt

Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fu Wei <fu.wei@linaro.org>
---
.../devicetree/bindings/watchdog/sbsa-gwdt.txt | 34 ++++++++++++++++++++++
Documentation/watchdog/watchdog-parameters.txt | 6 ++++
2 files changed, 40 insertions(+)

diff --git a/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt
new file mode 100644
index 0000000..2da63db
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/sbsa-gwdt.txt
@@ -0,0 +1,34 @@
+* SBSA (Server Base System Architecture) Generic Watchdog
+
+The SBSA Generic Watchdog Timer is used to force a reset of the system
+after two stages of timeout have elapsed. A detailed definition of the
+watchdog timer can be found in the ARM document: ARM-DEN-0029 - Server
+Base System Architecture (SBSA)
+
+Required properties:
+- compatible: Should at least contain "arm,sbsa-gwdt".
+
+- reg: Each entry specifies the base physical address of a register frame
+ and the length of that frame; currently, two frames must be defined,
+ in this order:
+ 1: Watchdog control frame;
+ 2: Refresh frame.
+
+- interrupts: Should contain the Watchdog Signal 0 (WS0) SPI (Shared
+ Peripheral Interrupt) number of SBSA Generic Watchdog.
+
+Optional properties
+- timeout-sec: Watchdog timeout and pre-timeout values.
+ If used, at least first timeout value (in seconds) must be provided.
+ A second optional value (in seconds) may also be provided and
+ will be used as the pre-timeout value, if it is given.
+
+Example for FVP Foundation Model v8:
+
+watchdog@2a440000 {
+ compatible = "arm,sbsa-gwdt";
+ reg = <0x0 0x2a440000 0 0x1000>,
+ <0x0 0x2a450000 0 0x1000>;
+ interrupts = <0 27 4>;
+ timeout-sec = <60 30>;
+};
diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt
index 9f9ec9f..e62c8c4 100644
--- a/Documentation/watchdog/watchdog-parameters.txt
+++ b/Documentation/watchdog/watchdog-parameters.txt
@@ -284,6 +284,12 @@ sbc_fitpc2_wdt:
margin: Watchdog margin in seconds (default 60s)
nowayout: Watchdog cannot be stopped once started
-------------------------------------------------
+sbsa_gwdt:
+timeout: Watchdog timeout in seconds. (default 60s)
+pretimeout: Watchdog pretimeout in seconds. (default 30s)
+nowayout: Watchdog cannot be stopped once started
+ (default=kernel config parameter)
+-------------------------------------------------
sc1200wdt:
isapnp: When set to 0 driver ISA PnP support will be disabled (default=1)
io: io port
--
2.5.0


\
 
 \ /
  Last update: 2015-11-09 09:01    [W:0.046 / U:0.596 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site