lkml.org 
[lkml]   [2015]   [Nov]   [4]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH V8] mm: memory hot-add: hot-added memory can not be added to movable zone by default

On Wed, 4 Nov 2015 18:20:14 +0800
Xishi Qiu <qiuxishi@huawei.com> wrote:

> On 2015/11/4 16:23, liuchangsheng wrote:
>
> > After the user config CONFIG_MOVABLE_NODE,
> > When the memory is hot added, should_add_memory_movable() return 0
> > because all zones including ZONE_MOVABLE are empty,
> > so the memory that was hot added will be assigned to ZONE_NORMAL,
> > and we need using the udev rules to online the memory automatically:
> > SUBSYSTEM=="memory", ACTION=="add", ATTR{state}=="offline",
> > ATTR{state}="online_movable"
> > The memory block onlined by udev must be adjacent to ZONE_MOVABLE.
> > The events of memory section are notified to udev asynchronously,
>
> Hi Yasuaki,
>

> If udev onlines memory in descending order, like 3->2->1->0, it will
> success, but we notifiy to udev in ascending order, like 0->1->2->3,
> so the udev rules cannot online memory as movable, right?

right.

>
> > so it can not ensure that the memory block onlined by udev is
> > adjacent to ZONE_MOVABLE.So it can't ensure memory online always success.
> > But we want the whole node to be added to ZONE_MOVABLE by default.
> >
> > So we change should_add_memory_movable(): if the user config
> > CONFIG_MOVABLE_NODE and movable_node kernel option
> > and the ZONE_NORMAL is empty or the pfn of the hot-added memory
> > is after the end of the ZONE_NORMAL it will always return 1
> > and then the whole node will be added to ZONE_MOVABLE by default.
> > If we want the node to be assigned to ZONE_NORMAL,
> > we can do it as follows:
> > "echo online_kernel > /sys/devices/system/memory/memoryXXX/state"
> >
>

> The order should like 0->1->2->3, right? 3->2->1->0 will be failed.

right.

Thanks,
Yasuaki Ishimatsu

>
> > Signed-off-by: liuchangsheng <liuchangsheng@inspur.com>
> > Signed-off-by: Xiaofeng Yan <yanxiaofeng@inspur.com>
> > Tested-by: Dongdong Fan <fandd@inspur.com>
> > Reviewed-by: <yasu.isimatu@gmail.com>
> > Cc: Wang Nan <wangnan0@huawei.com>
> > Cc: Dave Hansen <dave.hansen@intel.com>
> > Cc: Yinghai Lu <yinghai@kernel.org>
> > Cc: Tang Chen <tangchen@cn.fujitsu.com>
> > Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
> > Cc: Toshi Kani <toshi.kani@hp.com>
> > Cc: Xishi Qiu <qiuxishi@huawei.com>
> > ---
> > mm/memory_hotplug.c | 7 +++++++
> > 1 file changed, 7 insertions(+)
> >
> > diff --git a/mm/memory_hotplug.c b/mm/memory_hotplug.c
> > index aa992e2..8617b9f 100644
> > --- a/mm/memory_hotplug.c
> > +++ b/mm/memory_hotplug.c
> > @@ -1201,6 +1201,9 @@ static int check_hotplug_memory_range(u64 start, u64 size)
> > /*
> > * If movable zone has already been setup, newly added memory should be check.
> > * If its address is higher than movable zone, it should be added as movable.
> > + * And if system boots up with movable_node and config CONFIG_MOVABLE_NOD and
> > + * added memory does not overlap the zone before MOVABLE_ZONE,
> > + * the memory is added as movable.
> > * Without this check, movable zone may overlap with other zone.
> > */
> > static int should_add_memory_movable(int nid, u64 start, u64 size)
> > @@ -1208,6 +1211,10 @@ static int should_add_memory_movable(int nid, u64 start, u64 size)
> > unsigned long start_pfn = start >> PAGE_SHIFT;
> > pg_data_t *pgdat = NODE_DATA(nid);
> > struct zone *movable_zone = pgdat->node_zones + ZONE_MOVABLE;
> > + struct zone *pre_zone = pgdat->node_zones + (ZONE_MOVABLE - 1);
> > +
> > + if (movable_node_is_enabled() && (zone_end_pfn(pre_zone) <= start_pfn))
> > + return 1;
> >
>
> Looks good to me.
>
> How about add some comment in mm/Kconfig?
>
> Thanks,
> Xishi Qiu
>
> > if (zone_is_empty(movable_zone))
> > return 0;
>
>
>


\
 
 \ /
  Last update: 2015-11-04 17:21    [W:0.052 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site