lkml.org 
[lkml]   [2015]   [Nov]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH 02/10] clockevents/drivers: add MPS2 Timer driver
On 25/11/15 15:10, Daniel Lezcano wrote:
> On 11/25/2015 03:51 PM, Vladimir Murzin wrote:
>> Hi Daniel,
>>
>> Thanks for you review, I agree on all concerns raised and address them
>> in the next version. Just some points to confirm below (I left only
>> relevant parts).
>>
>>>> +static irqreturn_t mps2_timer_interrupt(int irq, void *dev_id)
>>>> +{
>>>> + struct clockevent_mps2 *ce = dev_id;
>>>> + u32 status = readl(ce->reg + TIMER_INT);
>>>> +
>>>> + if (!status)
>>>> + return IRQ_NONE;
>>>
>>> Why that could happen ? Add a comment.
>>>
>>
>> Sort of defensive programming, I never seen it happens, but just in case
>> of spurious interrupts... Do you prefer to get rid of this check or
>>
>> /* spurious interrupt? */
>> if (!status)
>> return IRQ_NONE;
>>
>> would be fine to you?
>
> Yes, that would be fine, but if it does never happen, we don't really
> need this check. If you prefer to make sure there isn't a spurious
> interrupt and considering it shouldn't happen, a pr_info trace may help
> to spot this misbehavior.
>

Good, I'll put pr_warn("spurious interrupt\n") then.

>>>> +}
>>>> +
>>>> +static void __init mps2_timer_init(struct device_node *np)
>>>> +{
>>>> + static int clksrc;
>>>> +
>>>> + if (!clksrc && !mps2_clocksource_init(np))
>>>> + clksrc = 1;
>>>> + else
>>>> + mps2_clockevents_init(np);
>>>
>>> That assumes the clocksource is defined before the clockevents in the
>>> DT. If it is not the case, the mps2_clocksource_init will fail (and spit
>>> errors) and mps2_clockevents_init() won't be called.
>>>
>>
>> Does following (stolen from efm32) look better to you?
>>
>> static void __init mps2_timer_init(struct device_node *np)
>> {
>> static int has_clocksource, has_clockevent;
>> int ret;
>>
>> if (!has_clocksource) {
>> ret = mps2_clocksource_init(np);
>> if (!ret) {
>> has_clocksource = 1;
>> return;
>> }
>> }
>>
>> if (!has_clockevent) {
>> ret = mps2_clockevent_init(np);
>> if (!ret) {
>> has_clockevent = 1;
>> return;
>> }
>> }
>> }
>
> Yes.
>
> I don't like to have a "CLOCKSOURCE_OF_DECLARE" to initialize a
> clockevent but I can't blame you, this is what is done in the other
> drivers.

Thanks for your time!

Vladimir

>
>>>> +}
>>>> +
>>>> +CLOCKSOURCE_OF_DECLARE(mps2_timer, "arm,mps2-timer", mps2_timer_init);
>>>>
>>>
>>>
>>
>
>



\
 
 \ /
  Last update: 2015-11-25 16:41    [W:1.581 / U:0.236 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site