lkml.org 
[lkml]   [2015]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH] drivers: ata: Move vendor specific sata port phy oob settings to device-tree
Date
Hi Rob,


Thanks for reviewing the patch

> -----Original Message-----
> From: Rob Herring [mailto:robh@kernel.org]
> Sent: Friday, November 13, 2015 8:02 PM
> To: Anurag Kumar Vulisha
> Cc: pawel.moll@arm.com; mark.rutland@arm.com;
> ijc+devicetree@hellion.org.uk; galak@codeaurora.org; tj@kernel.org;
> devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; linux-
> ide@vger.kernel.org; Michal Simek; Punnaiah Choudary Kalluri; Anirudha
> Sarangi; Srikanth Vemula; Anurag Kumar Vulisha
> Subject: Re: [PATCH] drivers: ata: Move vendor specific sata port phy oob
> settings to device-tree
>
> On Fri, Nov 13, 2015 at 04:02:23PM +0530, Anurag Kumar Vulisha wrote:
> > In SATA, speed negotiation happens with OOB(Out of Band) signals.
> > These OOB signal timing values are configured through vendor specific
> > registers in the SATA controller. These OOB timings depends on the
> > generator and detector clock frequency, which varies from board to
> > board (ex: ep108, zcu102 and zc1751 has different clock frequencies).
>
> Could you calculate the timings based on the frequency instead?
>

We can calculate the OOB timing settings based on frequency, but it requires complex calculations and floating
point operations in the sata driver , which is running in kernel mode. To my knowledge it is not recommended
to do floating operations inside kernel mode(Please correct me if I wrong ) . Because of this reason we are reading
those values from device tree.

> > Since to make ahci_ceva driver generic, it would be better to move
> > these settings to the device-tree node and read them from driver.
> >
> > This patch does the same.
> >
> > Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
> > ---
> > .../devicetree/bindings/ata/ahci-ceva.txt | 38 +++++++++
> > drivers/ata/ahci_ceva.c | 84 ++++++++++++++------
> > 2 files changed, 99 insertions(+), 23 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> > b/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> > index 7ca8b97..66fcd10 100644
> > --- a/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> > +++ b/Documentation/devicetree/bindings/ata/ahci-ceva.txt
> > @@ -5,6 +5,36 @@ Required properties:
> > - compatible: Compatibility string. Must be 'ceva,ahci-1v84'.
> > - clocks: Input clock specifier. Refer to common clock bindings.
> > - interrupts: Interrupt specifier. Refer to interrupt binding.
> > + - ceva,p0-cominit-params: OOB timing value for COMINIT parameter for
> port 0.
> > + - ceva,p1-cominit-params: OOB timing value for COMINIT parameter for
> port 1.
>
> This doesn't really scale when you have more than 2 ports. Given that you
> know the length for each port, just make it a single property (i.e.
> an array of ports).
>
The ceva sata controller that we are using has support for 2 ports only and each port can
Invidually configured to have different timing settings based on frequency. So for ease of
use we thought of having separate DT parameters for port 0 and 1 .

> > + The fields for the above parameter must be as shown
> below:
> > + ceva,phy-cominit-params = /bits/ 8 <CIBGMN
> CIBGMX CIBGN CINMP>;
> > + CINMP : COMINIT Negate Minimum Period.
> > + CIBGN : COMINIT Burst Gap Nominal.
> > + CIBGMX: COMINIT Burst Gap Maximum.
> > + CIBGMN: COMINIT Burst Gap Minimum.
> > + - ceva,p0-comwake-params: OOB timing value for COMWAKE
> parameter for port 0.
> > + - ceva,p1-comwake-params: OOB timing value for COMWAKE
> parameter for port 1.
> > + The fields for the above parameter must be as shown
> below:
> > + ceva,phy-comwake-params = /bits/ 8 <CWBGMN
> CWBGMX CWBGN CWNMP>;
> > + CWBGMN: COMWAKE Burst Gap Minimum.
> > + CWBGMX: COMWAKE Burst Gap Maximum.
> > + CWBGN: COMWAKE Burst Gap Nominal.
> > + CWNMP: COMWAKE Negate Minimum Period.
> > + - ceva,p0-burst-params: Burst timing value for COM parameter for port
> 0.
> > + - ceva,p1-burst-params: Burst timing value for COM parameter for port
> 1.
> > + The fields for the above parameter must be as shown
> below:
> > + ceva,phy-burst-params = /bits/ 8 <BMX BNM SFD
> PTST>;
> > + BMX: COM Burst Maximum.
> > + BNM: COM Burst Nominal.
> > + SFD: Signal Failure Detection value.
> > + PTST: Partial to Slumber timer value.
> > + - ceva,p0-retry-params: Retry interval timing value for port 0.
> > + - ceva,p1-retry-params: Retry interval timing value for port 1.
> > + The fields for the above parameter must be as shown
> below:
> > + ceva,phy-retry-params = /bits/ 16 <RIT RCT>;
> > + RIT: Retry Interval Timer.
> > + RCT: Rate Change Timer.
> >
> > Optional properties:
> > - ceva,broken-gen2: limit to gen1 speed instead of gen2.
> > @@ -17,4 +47,12 @@ Examples:
> > interrupts = <0 133 4>;
> > clocks = <&clkc SATA_CLK_ID>;
> > ceva,broken-gen2;
> > + ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
> > + ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
> > + ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
> > + ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>;
> > + ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
> > + ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
> > + ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
> > + ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
> > };
> > diff --git a/drivers/ata/ahci_ceva.c b/drivers/ata/ahci_ceva.c index
> > 207649d..59de2ca 100644
> > --- a/drivers/ata/ahci_ceva.c
> > +++ b/drivers/ata/ahci_ceva.c
> > @@ -50,21 +50,6 @@
> > #define PPCFG_PSS_EN (1 << 29)
> > #define PPCFG_ESDF_EN (1 << 31)
> >
> > -#define PP2C_CIBGMN 0x0F
> > -#define PP2C_CIBGMX (0x25 << 8)
> > -#define PP2C_CIBGN (0x18 << 16)
> > -#define PP2C_CINMP (0x29 << 24)
> > -
> > -#define PP3C_CWBGMN 0x04
> > -#define PP3C_CWBGMX (0x0B << 8)
> > -#define PP3C_CWBGN (0x08 << 16)
> > -#define PP3C_CWNMP (0x0F << 24)
> > -
> > -#define PP4C_BMX 0x0a
> > -#define PP4C_BNM (0x08 << 8)
> > -#define PP4C_SFD (0x4a << 16)
> > -#define PP4C_PTST (0x06 << 24)
> > -
> > #define PP5C_RIT 0x60216
> > #define PP5C_RCT (0x7f0 << 20)
> >
> > @@ -87,6 +72,11 @@
> >
> > struct ceva_ahci_priv {
> > struct platform_device *ahci_pdev;
> > + /* Port Phy2Cfg Register */
> > + u32 pp2c[NR_PORTS];
> > + u32 pp3c[NR_PORTS];
> > + u32 pp4c[NR_PORTS];
> > + u32 pp5c[NR_PORTS];
> > int flags;
> > };
> >
> > @@ -131,20 +121,16 @@ static void ahci_ceva_setup(struct ahci_host_priv
> *hpriv)
> > writel(tmp, mmio + AHCI_VEND_PPCFG);
> >
> > /* Phy Control OOB timing parameters COMINIT */
> > - tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN |
> PP2C_CINMP;
> > - writel(tmp, mmio + AHCI_VEND_PP2C);
> > + writel(cevapriv->pp2c[i], mmio + AHCI_VEND_PP2C);
> >
> > /* Phy Control OOB timing parameters COMWAKE */
> > - tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN |
> PP3C_CWNMP;
> > - writel(tmp, mmio + AHCI_VEND_PP3C);
> > + writel(cevapriv->pp3c[i], mmio + AHCI_VEND_PP3C);
> >
> > /* Phy Control Burst timing setting */
> > - tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST;
> > - writel(tmp, mmio + AHCI_VEND_PP4C);
> > + writel(cevapriv->pp4c[i], mmio + AHCI_VEND_PP4C);
> >
> > /* Rate Change Timer and Retry Interval Timer setting */
> > - tmp = PP5C_RIT | PP5C_RCT;
> > - writel(tmp, mmio + AHCI_VEND_PP5C);
> > + writel(cevapriv->pp5c[i], mmio + AHCI_VEND_PP5C);
> >
> > /* Rx Watermark setting */
> > tmp = PTC_RX_WM_VAL | PTC_RSVD;
> > @@ -187,6 +173,58 @@ static int ceva_ahci_probe(struct platform_device
> *pdev)
> > if (of_property_read_bool(np, "ceva,broken-gen2"))
> > cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
> >
> > + /* Read OOB timing value for COMINIT from device-tree */
> > + if (of_property_read_u8_array(np, "ceva,p0-cominit-params",
> > + (u8 *)&cevapriv->pp2c[0], 4) < 0) {
> > + dev_warn(dev, "ceva,p0-cominit-params property not
> defined\n");
>
> I'd really like to move all the error prints into the of_property_* functions
> instead, but then we'd probably need *_optional variants to avoid spewing
> to the console.

We will try to implement this later.

Thanks,
Anurag Kumar V



\
 
 \ /
  Last update: 2015-11-17 15:41    [W:0.082 / U:1.308 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site