lkml.org 
[lkml]   [2015]   [Nov]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 22/26] Input: synaptics-rmi4 - Add F30 support
From
Date
On 11/09/2015 03:25 PM, Dmitry Torokhov wrote:
> On Mon, Nov 09, 2015 at 02:54:08PM -0800, Andrew Duggan wrote:
>> On 11/09/2015 06:06 AM, Benjamin Tissoires wrote:
>>> Hey Linus,
>>>
>>> first thanks for the reviews. Much appreciated.
>>>
>>> On Mon, Nov 9, 2015 at 2:32 PM, Linus Walleij <linus.walleij@linaro.org> wrote:
>>>> On Fri, Nov 6, 2015 at 12:42 AM, Andrew Duggan <aduggan@synaptics.com> wrote:
>>>>
>>>>> From: Benjamin Tissoires <benjamin.tissoires@redhat.com>
>>>>>
>>>>> RMI4 Function 0x30 provides support for GPIOs, LEDs and mechanical
>>>>> buttons. In particular, the mechanical button support is used in
>>>>> an increasing number of touchpads.
>>>>>
>>>>> [BT] cured the code to rely only on the unified input node created
>>>>> by rmi_driver.
>>>>>
>>>>> Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
>>>>> Signed-off-by: Allie Xiong <axiong@synaptics.com>
>>>>> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
>>>> I see this function driver is not yet adding any gpio_chip or
>>>> LEDs class devices, which is fine, we can add that later when
>>>> we have something to test. Or is iit using that LED feature
>>>> in the input layer that corresponds to caps lock etc?
>> F30 is currently only used in touchpads and mostly used to report
>> the the click of the tact switch on clickpads. When the GPIO
>> interrupts we report the appropriate button event to the host.
>> Because the GPIOs are wired to our ASIC and not to the host I'm not
>> sure there is any benefit to exposing it to the host using
>> gpio_chip.
>>
>> Dmitry asked a similar question and here is my response to him:
>> http://www.spinics.net/lists/linux-input/msg40458.html
>>
>> There are a few rmi touchpads which have LEDs in the top left corner
>> to indicate if the touchpad has been enabled / disabled. Writing to
>> a register in F30 would turn on and off the LED. I don't think they
>> are being made anymore so I haven't really looked into how we would
>> implement this. If there is something in the input layer for
>> controlling LEDs that might be the way to do it.
> No, it should be eventually exported as a generic LED (input core itself
> now registers its capslock, etc leds with LED core and I do not plan on
> adding new input LEDs).
>
>>> Do not take my words as the official ones, but when we discussed with
>>> Synaptics about F30 (and unified input), they told us that they
>>> designed the driver based on the phone use case. In such use case, the
>>> power (and maybe LEDs) are handled through F30, and the touchscreen
>>> through F11/12. Problem is, I am not even sure there are phones around
>>> with such F30/F11 combination.
>>>
>>> So in the end, from what I can see, F30 is used for buttons on
>>> touchpads/clickpads, and LEDs when there are some on these touchpads.
>>>
>>> I don't know if the keyboards would use F30 for their LEDs though.
>>>
>>> That being said. Unless Synaptics tells us that there are uses of a
>>> non "unified" input device somewhere, I would also agree to only keep
>>> the "unified" input node, which would simplify both F11/12 and F30.
>> The original architecture of the driver was to have each function
>> have it's own input device. The reasoning was that you would have a
>> phone with a touchscreen (F11) and maybe some capacitive buttons
>> (F19 or F1A or something) and that the system should see these as
>> two separate devices. I'm wondering if this is needed though. Would
>> userspace care if a touchscreen also reported KEY_HOME, KEY_BACK, or
>> KEY_MENU?
>>
>> At this point I agree, it's probably time to just have F11, F12, and
>> F30 all report from the input device created in rmi_driver and
>> remove the non unified option. If someday there is a function which
>> needs to report data from a different input device it can just
>> create it in that function.
> Hmm.. if F30 is used for clickpads I agree that we'd want to mix it in
> with the F11 data. But for generic capacitive buttons I think it would
> be better if they are reported separately. Whether we want to do that
> form F30 or have F30 actually export gpios and use gpio-keys to actually
> create input device - I am open to discussing.
>
> Thanks.
>

I would suggest that we get rid of the unified input option and always
create an input device in rmi_driver and that can be the default input
device which F11 and F12 can use to report events. Then in the case of
capacitive buttons we can create an input device internally in that
function driver specificity for those events so they can be reported
separately. F30 will also use the default input device in the case of
touchpads.

I don't know of any non touchpad devices which use F30 and I think it's
unlikely that there would be any. I think it's really meant for
controlling the buttons and LEDs which are on the touchpad PCB. There
probably isn't much reason to wire external GPIOs and LEDs to be
controlled by our ASIC*. If such a device existed then exporting GPIOs
with gpio_chip and using gpio-keys seems like a reasonable way to do it.
I'm just not sure we will have devices which need to use that
implementation.

* There is the one exception which is the Lenovo systems which have the
external physical stick buttons are wired to our ASIC, but that is a
special case and it's events should be forwarded to the stick's input
device instead of being reported separately using gpio-keys.

Andrew




\
 
 \ /
  Last update: 2015-11-11 20:21    [W:0.091 / U:0.044 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site