lkml.org 
[lkml]   [2015]   [Nov]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 1/6] net: dsa: mv88e6060: remove poll_link callback
Date
As of mv88e6xxx remove the poll_link callback since the link
state change polling is now handled by the phylib.

Tested on a mv88e6060 B0 device with a TI DM816X SoC.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
drivers/net/dsa/mv88e6060.c | 49 ---------------------------------------------
1 file changed, 49 deletions(-)

diff --git a/drivers/net/dsa/mv88e6060.c b/drivers/net/dsa/mv88e6060.c
index 9093577..6885ef5 100644
--- a/drivers/net/dsa/mv88e6060.c
+++ b/drivers/net/dsa/mv88e6060.c
@@ -225,54 +225,6 @@ mv88e6060_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
return reg_write(ds, addr, regnum, val);
}

-static void mv88e6060_poll_link(struct dsa_switch *ds)
-{
- int i;
-
- for (i = 0; i < DSA_MAX_PORTS; i++) {
- struct net_device *dev;
- int uninitialized_var(port_status);
- int link;
- int speed;
- int duplex;
- int fc;
-
- dev = ds->ports[i];
- if (dev == NULL)
- continue;
-
- link = 0;
- if (dev->flags & IFF_UP) {
- port_status = reg_read(ds, REG_PORT(i), 0x00);
- if (port_status < 0)
- continue;
-
- link = !!(port_status & 0x1000);
- }
-
- if (!link) {
- if (netif_carrier_ok(dev)) {
- netdev_info(dev, "link down\n");
- netif_carrier_off(dev);
- }
- continue;
- }
-
- speed = (port_status & 0x0100) ? 100 : 10;
- duplex = (port_status & 0x0200) ? 1 : 0;
- fc = ((port_status & 0xc000) == 0xc000) ? 1 : 0;
-
- if (!netif_carrier_ok(dev)) {
- netdev_info(dev,
- "link up, %d Mb/s, %s duplex, flow control %sabled\n",
- speed,
- duplex ? "full" : "half",
- fc ? "en" : "dis");
- netif_carrier_on(dev);
- }
- }
-}
-
static struct dsa_switch_driver mv88e6060_switch_driver = {
.tag_protocol = DSA_TAG_PROTO_TRAILER,
.probe = mv88e6060_probe,
@@ -280,7 +232,6 @@ static struct dsa_switch_driver mv88e6060_switch_driver = {
.set_addr = mv88e6060_set_addr,
.phy_read = mv88e6060_phy_read,
.phy_write = mv88e6060_phy_write,
- .poll_link = mv88e6060_poll_link,
};

static int __init mv88e6060_init(void)
--
1.9.1

\
 
 \ /
  Last update: 2015-11-10 17:01    [W:0.046 / U:0.304 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site