Messages in this thread Patch in this message | | | Date | Mon, 26 Jan 2015 11:46:59 +0000 | From | Mark Rutland <> | Subject | Re: [PATCH 4/7] ARM: at91: enable the L2 Cache controller |
| |
On Mon, Jan 26, 2015 at 10:07:16AM +0000, Wenyou Yang wrote: > Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> > --- > arch/arm/mach-at91/board-dt-sama5.c | 53 +++++++++++++++++++++++++++++++++++ > 1 file changed, 53 insertions(+) > > diff --git a/arch/arm/mach-at91/board-dt-sama5.c b/arch/arm/mach-at91/board-dt-sama5.c > index 86cffcd..ed6db28 100644 > --- a/arch/arm/mach-at91/board-dt-sama5.c > +++ b/arch/arm/mach-at91/board-dt-sama5.c > @@ -17,17 +17,70 @@ > #include <linux/of_platform.h> > #include <linux/phy.h> > #include <linux/clk-provider.h> > +#include <linux/of_address.h> > > #include <asm/setup.h> > #include <asm/irq.h> > #include <asm/mach/arch.h> > #include <asm/mach/map.h> > #include <asm/mach/irq.h> > +#include <asm/hardware/cache-l2x0.h> > > #include "generic.h" > > +void __iomem *at91_l2cc_base; > +EXPORT_SYMBOL_GPL(at91_l2cc_base); > + > +#ifdef CONFIG_CACHE_L2X0 > +static void __init at91_init_l2cache(void) > +{ > + struct device_node *np; > + u32 reg; > + > + np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache"); > + if (!np) > + return; > + > + at91_l2cc_base = of_iomap(np, 0); > + if (!at91_l2cc_base) > + panic("unable to map l2cc cpu registers\n"); > + > + of_node_put(np); > + > + /* Disable cache if it hasn't been done yet */ > + if (readl_relaxed(at91_l2cc_base + L2X0_CTRL) & L2X0_CTRL_EN) > + writel_relaxed(~L2X0_CTRL_EN, at91_l2cc_base + L2X0_CTRL); > + > + /* Prefetch Control */ > + reg = readl_relaxed(at91_l2cc_base + L310_PREFETCH_CTRL); > + reg &= ~L310_PREFETCH_CTRL_OFFSET_MASK; > + reg |= 0x01; > + reg |= L310_PREFETCH_CTRL_DBL_LINEFILL_INCR; > + reg |= L310_PREFETCH_CTRL_PREFETCH_DROP; > + reg |= L310_PREFETCH_CTRL_DATA_PREFETCH; > + reg |= L310_PREFETCH_CTRL_INSTR_PREFETCH; > + reg |= L310_PREFETCH_CTRL_DBL_LINEFILL; > + writel_relaxed(reg, at91_l2cc_base + L310_PREFETCH_CTRL); > + > + /* Power Control */ > + reg = readl_relaxed(at91_l2cc_base + L310_POWER_CTRL); > + reg |= L310_STNDBY_MODE_EN; > + reg |= L310_DYNAMIC_CLK_GATING_EN; > + writel_relaxed(reg, at91_l2cc_base + L310_POWER_CTRL); > + > + /* Disable interrupts */ > + writel_relaxed(0x00, at91_l2cc_base + L2X0_INTR_MASK); > + writel_relaxed(0x01ff, at91_l2cc_base + L2X0_INTR_CLEAR); > + l2x0_of_init(0, ~0UL); > +} > +#else > +static inline void at91_init_l2cache(void) {} > +#endif
This poking of the PL310 should live in the cache_l2x0 driver.
Mark.
| |