lkml.org 
[lkml]   [2014]   [Jul]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 2/4] mfd: pm8xxx-spmi: document DT bindings for Qualcomm SPMI PMICs
Date
Document DT bindings used to describe the Qualcomm SPMI PMICs.
Currently the SPMI PMICs supported are pm8941, pm8841 and pma8084.

Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
---
.../devicetree/bindings/mfd/qcom,pm8xxx-spmi.txt | 49 ++++++++++++++++++++
1 files changed, 49 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/qcom,pm8xxx-spmi.txt

diff --git a/Documentation/devicetree/bindings/mfd/qcom,pm8xxx-spmi.txt b/Documentation/devicetree/bindings/mfd/qcom,pm8xxx-spmi.txt
new file mode 100644
index 0000000..2b7f5b6
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom,pm8xxx-spmi.txt
@@ -0,0 +1,49 @@
+ Qualcomm PM8XXX SPMI PMICs multi-function device bindings
+
+The Qualcomm PM8XXX series presently includes PM8941, PM8841 and PMA8084
+PMICs. These PMICs use a QPNP scheme through SPMI interface.
+QPNP is effectively a partitioning scheme for dividing the SPMI extended
+register space up into logical pieces, and set of fixed register
+locations/definitions within these regions, with some of these regions
+specifically used for interrupt handling.
+
+The QPNP PMICs are used with the Qualcomm Snapdragon series SoCs, and are
+interfaced to the chip via the SPMI (System Power Management Interface) bus.
+Support for multiple independent functions are implemented by splitting the
+16-bit SPMI slave address space into 256 smaller fixed-size regions, 256 bytes
+each. A function can consume one or more of these fixed-size register regions.
+
+Required properties:
+- compatible: Should contain one of:
+ "qcom,pm8941"
+ "qcom,pm8841"
+ "qcom,pma8084"
+- reg: Specifies the SPMI USID slave address for this device.
+ For more information see:
+ Documentation/devicetree/bindings/spmi/spmi.txt
+
+Required properties for peripheral child nodes:
+- compatible: Should contain "qcom,pm8xxx-xxx", where "xxx" is
+ peripheral name. The "pm8xxx" can be any of supported PMICs,
+ see example below.
+
+Optional properties for peripheral child nodes:
+- interrupts: Interrupts are specified as a 4-tuple. For more information
+ see:
+ Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.txt
+- interrupt-names: Corresponding interrupt name to the interrupts property
+
+Each child node represents a function of the PMIC.
+
+Example:
+
+ pm8941@0 {
+ compatible = "qcom,pm8941";
+ reg = <0x0 SPMI_USID>;
+
+ rtc {
+ compatible = "qcom,pm8941-rtc";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "alarm";
+ };
+ };
--
1.7.0.4


\
 
 \ /
  Last update: 2014-07-24 15:22    [W:0.092 / U:6.432 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site