lkml.org 
[lkml]   [2014]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 6/8 V2] staging: dgap: remove unneeded dgap_err()
On 07/16/2014 05:26 AM, DaeSeok Youn wrote:
> 2014-07-16 8:50 GMT+09:00 Greg KH <gregkh@linuxfoundation.org>:
>> On Wed, Jul 16, 2014 at 08:21:30AM +0900, DaeSeok Youn wrote:
>>> Hi,
>>>
>>> 2014-07-16 0:29 GMT+09:00 Greg KH <gregkh@linuxfoundation.org>:
>>>> On Tue, Jul 15, 2014 at 06:11:44PM +0900, Daeseok Youn wrote:
>>>>> The dgap_err() is printing a message with pr_err(),
>>>>> so all those are replaced.
>>>>>
>>>>> Use definition "pr_fmt" and then all of "dgap:" in
>>>>> the beginning of print messages are removed.
>>>>>
>>>>> And also removed "out of memory" message because
>>>>> the kernel has own message for that.
>>>>>
>>>>> Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
>>>>> ---
>>>>> V2: use pr_fmt "dgap:" prefix on print message on dgap.
>>>>> remove "out of memory" message.
>>>>>
>>>>> Adds Mark to TO list and CC list for checking send
>>>>> this email properly to him.
>>>>>
>>>>> drivers/staging/dgap/dgap.c | 306 +++++++++++++++++++------------------------
>>>>> 1 files changed, 133 insertions(+), 173 deletions(-)
>>>>>
>>>>> diff --git a/drivers/staging/dgap/dgap.c b/drivers/staging/dgap/dgap.c
>>>>> index 06c55cb..9e750fb 100644
>>>>> --- a/drivers/staging/dgap/dgap.c
>>>>> +++ b/drivers/staging/dgap/dgap.c
>>>>> @@ -41,6 +41,8 @@
>>>>> */
>>>>> #undef DIGI_CONCENTRATORS_SUPPORTED
>>>>>
>>>>> +#define pr_fmt(fmt) "dgap: " fmt
>>>>> +
>>>>> #include <linux/kernel.h>
>>>>> #include <linux/module.h>
>>>>> #include <linux/pci.h>
>>>>> @@ -153,7 +155,6 @@ static void dgap_firmware_reset_port(struct channel_t *ch);
>>>>> static int dgap_gettok(char **in);
>>>>> static char *dgap_getword(char **in);
>>>>> static int dgap_checknode(struct cnode *p);
>>>>> -static void dgap_err(char *s);
>>>>>
>>>>> /*
>>>>> * Function prototypes from dgap_sysfs.h
>>>>> @@ -815,7 +816,7 @@ static struct board_t *dgap_found_board(struct pci_dev *pdev, int id,
>>>>> if (ret)
>>>>> goto free_brd;
>>>>>
>>>>> - pr_info("dgap: board %d: %s (rev %d), irq %ld\n",
>>>>> + pr_info("board %d: %s (rev %d), irq %ld\n",
>>>>> boardnum, brd->name, brd->rev, brd->irq);
>>>>
>>>> Almost all of the pr_*() calls in this driver should be converted over
>>>> to use dev_*() calls instead. And some of them, like this one, should
>>>> be removed entirely (no need for a driver to be "noisy" when a device
>>>> for it is found, it should be quiet if at all possible, unless something
>>>> went wrong.)
>>>>
>>>> So can you do that here instead? I've applied the earlier patches in
>>>> this series, and stopped here.
>>> OK. I can. pr_*() calls are replaced with dev_*() calls.
>>> And also removes some of print message which are useless like "out
>>> of memory"
>>
>> Yes, please do that, that would be great.
> I have been working to change pr_*() to dev_*(), but dgap_parse() has no
> "struct device" for using dev_*(). If dgap_parse still need for this driver,
> it need to take a parameter for using dev_*(), it may be "pdev" but
> configuration
> file doesn't need to parse in kernel at all, dgap_parse() will be removed.
>
> So I will wait to verify by Mark about parsing configuration file.
>
> Thanks.
>
> regards,
> Daeseok Youn.
>

Hi Daeseok,

I would wait on that one for now. I know that code has to be removed
eventually. I'm just not sure if we are quite ready. That is actually a
LOT of lines of code also. I think a couple of things need done first.

Here is a sample config file created by one of DIGI's user land
applications (mpi). These entries are only for 2 different cards. There
are others cards that may have other things to consider. I only have
these 2 cards types now. I had a third type which is just a 2 port but
that one is gone now.

config_begin
board Digi_AccelePort_8r_920_PCI
io 0x000
mem 0x000000
start 1
nports 8
ttyname ttya
altpin 0
useintr 0
board Digi_AccelePort_4r_920_PCI
io 0x000
mem 0x000000
start 1
nports 4
ttyname ttyb
altpin 0
useintr 0
board Digi_AccelePort_8r_920_PCI
io 0x000
mem 0x000000
start 1
nports 8
ttyname ttyc
altpin 0
useintr 0
config_end

The altpin and useintr parameters need to be converted to module
parameters. I found references in the code somewhere that the nports may
not be reliably known using the device id for at least one card type.
All the other stuff in this particular config file is pretty much
useless. Well, sort of. The ttyname parameter is used by the driver to
populate a "sys" file with a custom device name that is then used by a
userland script and udev to allow a user to define his own device
names. Custom links are created. Perhaps this also would be nice to have
as a module param?

Also, there is a userland utility (dpa) that is used to set some
parameters of the card. Sort of like stty except it is for "special"
things that the kernel does not directly support. Like special baud
rates and such. I'm not sure what to do about that one. I personally
have never used these "special" things but I'm sure they are used by
someone somewhere?? I saw some code removed related to "dpa" recently.
This came to mind.

Regards
Mark








\
 
 \ /
  Last update: 2014-07-16 17:01    [W:0.120 / U:0.380 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site