lkml.org 
[lkml]   [2014]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 1/8] of: Add NVIDIA Tegra SATA controller binding
On 07/16/2014 02:24 PM, Mikko Perttunen wrote:
> This patch adds device tree binding documentation for the SATA
> controller found on NVIDIA Tegra SoCs.
>
> Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
> ---
> .../devicetree/bindings/ata/tegra-sata.txt | 30 ++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/ata/tegra-sata.txt
>
> diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt
> new file mode 100644
> index 0000000..946f207
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt
> @@ -0,0 +1,30 @@
> +Tegra124 SoC SATA AHCI controller
> +
> +Required properties :
> +- compatible : "nvidia,tegra124-ahci".
> +- reg : Should contain 2 entries:
> + - AHCI register set (SATA BAR5)
> + - SATA register set
> +- interrupts : Defines the interrupt used by SATA
> +- clocks : Must contain an entry for each entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names : Must include the following entries:
> + - sata
> + - sata-oob
> + - cml1
> + - pll_e

It would be more readable if it like this...

Required properties :
- compatible : "nvidia,tegra124-ahci".
- reg : Should contain 2 entries:
- AHCI register set (SATA BAR5)
- SATA register set
- interrupts : Defines the interrupt used by SATA
- clocks : Must contain an entry for each entry in clock-names.
See ../clocks/clock-bindings.txt for details.
....

> +- resets : Must contain an entry for each entry in reset-names.
> + See ../reset/reset.txt for details.
> +- reset-names : Must include the following entries:
> + - sata
> + - sata-oob
> + - sata-cold
> +- phys : Must contain an entry for each entry in phy-names.
> + See ../phy/phy-bindings.txt for details.
> +- phy-names : Must include the following entries:
> + - sata-phy : XUSB PADCTL SATA PHY
> +- hvdd-supply : Defines the SATA HVDD regulator
> +- vddio-supply : Defines the SATA VDDIO regulator
> +- avdd-supply : Defines the SATA AVDD regulator
> +- target-5v-supply : Defines the SATA 5V power regulator
> +- target-12v-supply : Defines the SATA 12V power regulator

Same....


--
Regards,
Varka Bhadram.



\
 
 \ /
  Last update: 2014-07-16 12:01    [W:0.256 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site