lkml.org 
[lkml]   [2014]   [Jul]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 1/2] ARM: at91/dt: describe rgmii ethernet phy connected to sama5d3xek boards
Hi Boris,

On 07/11/2014 03:59 AM, Boris BREZILLON wrote:
> Add ethernet-phy nodes and specify phy interrupt (connected to pin PB25)
> and board specific timing configs.
>
> Atmel has two different HW designs for its CPU modules: the first one
> (produced by Embest) is connecting PHYAD[0-2] pins to pull up resistors
> and the other one (produced by Ronetix) is connecting PHYAD0 to a pull up
> resistor and PHYAD[1-2] to pull down resistors.
> As a result, Ronetix design will have its PHY available at address 0x1 and
> Embest design at 0x7.
> By defining both phys we're letting the phy core detect the one actually
> available on the MDIO bus.
>
> Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>

For this patch series, test OK on both Embest (sama5d34ek) and Ronetix
(sama5d33ek).

Tested-by: Bo Shen <voice.shen@atmel.com>

> ---
>
> Florian, I dropped your Reviewed-by tag because this patch has slightly
> changed.
>
>
> arch/arm/boot/dts/sama5d3xcm.dtsi | 30 ++++++++++++++++++++++++++++++
> 1 file changed, 30 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sama5d3xcm.dtsi b/arch/arm/boot/dts/sama5d3xcm.dtsi
> index b0b1331..755369e 100644
> --- a/arch/arm/boot/dts/sama5d3xcm.dtsi
> +++ b/arch/arm/boot/dts/sama5d3xcm.dtsi
> @@ -34,6 +34,36 @@
>
> macb0: ethernet@f0028000 {
> phy-mode = "rgmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet-phy@1 {
> + reg = <0x1>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> +
> + ethernet-phy@7 {
> + reg = <0x7>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> };
>
> pmc: pmc@fffffc00 {
>

Best Regards,
Bo Shen



\
 
 \ /
  Last update: 2014-07-11 04:21    [W:0.300 / U:0.332 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site