lkml.org 
[lkml]   [2014]   [Dec]   [19]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/9] hwmon: dts: Doc: Add DTS doc to explain how to use PWM FAN as a cooling device
Hi Guenter,

> On Fri, Dec 19, 2014 at 04:32:24PM +0100, Lukasz Majewski wrote:
> > Hi Sjoerd,
> >
> > Thanks for your feedback and sorry for a late reply.
> >
> > > On Thu, 2014-12-18 at 11:13 +0100, Lukasz Majewski wrote:
> > > > Several new properties to allow PWM fan working as a cooling
> > > > device have been combined into this single commit.
> > > >
> > > > Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
> > > > ---
> > > > .../devicetree/bindings/hwmon/pwm-fan.txt | 28
> > > > ++++++++++++++++++++++ 1 file changed, 28 insertions(+)
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt
> > > > b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt index
> > > > 610757c..3877810 100644 ---
> > > > a/Documentation/devicetree/bindings/hwmon/pwm-fan.txt +++
> > > > b/Documentation/devicetree/bindings/hwmon/pwm-fan.txt @@ -3,10
> > > > +3,38 @@ Bindings for a fan connected to the PWM lines Required
> > > > properties:
> > > > - compatible : "pwm-fan"
> > > > - pwms : the PWM that is used to control the
> > > > PWM fan +- cooling-pwm-values : PWM duty cycle values
> > > > relative to
> > > > + cooling-max-pwm-value correspondig
> > > > to
> > > > + proper cooling states
> > > > +- default-pulse-width : Property specifying default pulse
> > > > width for FAN
> > > > + at system boot (zero to disable
> > > > FAN on boot).
> > > > + Allowed range is 0 to 255
> > >
> > > The 0..255 range seems somewhat random. Would be nicer to either
> > > use the approach of pwm-backlight (iotw, have the range go from
> > > the first to the last entry of cooling-pwm-values)
> >
> > I'm OK to change the default-pulse-width to be similar to
> > "default-brightness-level" (as it is in
> > Documentation/devicetree/bindings/video/backlight/pwm-backlight.txt)
> >
> > > or simply have be the duty
> > > lenght in NS as entries instead of the current indirection.
> >
> > I'd prefer to keep the indirection - as it is utilized in the
> > current pwm-fan.c driver.
> >
> FWIW, devicetree information is supposed to be implementation
> independent. So this is a poor argument.

Many other pwm drivers use the indirection - e.g. mentioned
pwm-backlight.


>
> >
> > Enabling pan to full RPM was the default behaviour in the current
> > pwm-fan.c file.
> >
> > To be honest, there is no need to enable fan to full RPM speed in
> > this board for following reasons:
> > 1. In Odroid the FAN is optional (stacked on top of a heat sink) -
> > very often it is just enough to only have the heat sink.
> >
> > 2. Odroid has thermal enabled by default and IMHO it would be more
> > feasible to allow thermal to control fan from the very beginning.
> >
> > However, I can also understand if the policy for hwmon implies a
> > rule to enable by default all fans to full RPM speed.
> >
> Why and how does that all suggest that the current default behavior
> should be changed ?

I wanted to avoid the unpleasant sound for full speed fan when thermal
is not enabled by default.

But as I said, I fully understand the policy and I would be happy to
comply with it as thermal should reduce the fan speed anyway at boot
time.

>
> Guenter



--
Best regards,

Lukasz Majewski

Samsung R&D Institute Poland (SRPOL) | Linux Platform Group


\
 
 \ /
  Last update: 2014-12-19 17:41    [W:0.233 / U:0.032 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site