lkml.org 
[lkml]   [2013]   [Sep]   [26]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/4] pinctrl: sh-pfc: r8a7790: add pin definitions for the I2C3 interface
Hi Laurent

On Wed, 25 Sep 2013, Laurent Pinchart wrote:

> Hi Guennadi,
>
> Thank you for the patch.
>
> On Monday 09 September 2013 18:03:53 Guennadi Liakhovetski wrote:
> > There are four I2C interfaces on r8a7790, each of them can be connected to
> > one of the two respective I2C controllers, e.g. interface #0 can be
> > configured to work with I2C0 or with IIC0. Additionally some of those
> > interfaces can also use one of several pin sets. Interface #3 is special,
> > because it can be used in automatic mode for DVFS. It only has one set
> > of pins available and those pins cannot be used for anything else, they
> > also lack the GPIO function.
> >
> > This patch uses the sh-pfc ability to configure pins, not associated with
> > GPIOs and adds support for I2C3 to the r8a7790 PFC set up.
>
> Ulrich Hecht sent a patch titled "sh-pfc: r8a7790: Add I2C pin groups and
> functions" that added pin groups for I2C1 and I2C2. The patch is available
> from
>
> git://linuxtv.org/pinchartl/fbdev.git pinmux/next
>
> If you need to resubmit this patch due to my comments below, could you please
> rebase it on top of that branch ?
>
> > Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
> > ---
> > drivers/pinctrl/sh-pfc/pfc-r8a7790.c | 28 ++++++++++++++++++++++++++++
> > 1 files changed, 28 insertions(+), 0 deletions(-)
> >
> > diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7790.c
> > b/drivers/pinctrl/sh-pfc/pfc-r8a7790.c index 64fcc006..c3c4d9b 100644
> > --- a/drivers/pinctrl/sh-pfc/pfc-r8a7790.c
> > +++ b/drivers/pinctrl/sh-pfc/pfc-r8a7790.c
> > @@ -781,6 +781,8 @@ enum {
> > ADICS_SAMP_MARK, DU2_CDE_MARK, QPOLB_MARK, SCIFA2_RXD_B_MARK,
> > USB1_PWEN_MARK, AUDIO_CLKOUT_D_MARK, USB1_OVC_MARK,
> > TCLK1_B_MARK,
> > +
> > + I2C3_SCL_MARK, I2C3_SDA_MARK,
> > PINMUX_MARK_END,
> > };
> >
> > @@ -1719,10 +1721,22 @@ static const u16 pinmux_data[] = {
> > PINMUX_IPSR_DATA(IP16_6, AUDIO_CLKOUT_D),
> > PINMUX_IPSR_DATA(IP16_7, USB1_OVC),
> > PINMUX_IPSR_MODSEL_DATA(IP16_7, TCLK1_B, SEL_TMU1_1),
> > +
> > + PINMUX_DATA(I2C3_SCL_MARK, FN_SEL_IICDVFS_1),
> > + PINMUX_DATA(I2C3_SDA_MARK, FN_SEL_IICDVFS_1),
>
> You introduce a way to mux the I2C3 function on those two pins, but no way to
> select the IICDVFS back. I don't think it's an issue, we can always add that
> later when (if) needed. Linus, is that fine with you ?

I did it on purpose, since I didn't have a use case for IICDVFS. I prefer
not to add too many things, that cannot be tested.

> > };
> >
> > +/* R8A7790 has 6 banks with 32 GPIOs in each = 192 GPIOs */
> > +#define ROW_GROUP_A(r) ('Z' - 'A' + 1 + (r))
> > +#define PIN_NUMBER(r, c) (((r) - 'A') * 16 + (c) + 200)
>
> The BGA package has 31 columns, shouldn't you multiply the row number by 31
> instead of 16 ?

Oops, you're right - the pin table is continued on the second page...

> As we have 192 GPIOs, shouldn't you use an offset of 192 instead of 200 ? This
> doesn't matter too much I guess.

On one of Renesas SoCs I've seen an offset of 2000 used. I thought it
would be an exaggeration in this case ;) but I followed the pattern of
using a round number for the offset, is this ok?

Thanks
Guennadi

> > +#define PIN_A_NUMBER(r, c) PIN_NUMBER(ROW_GROUP_A(r), c)
> > +
> > static struct sh_pfc_pin pinmux_pins[] = {
> > PINMUX_GPIO_GP_ALL(),
> > +
> > + /* Pins not associated with a GPIO port */
> > + SH_PFC_PIN_NAMED(ROW_GROUP_A('J'), 15, AJ15),
> > + SH_PFC_PIN_NAMED(ROW_GROUP_A('H'), 15, AH15),
> > };
> >
> > /* - DU RGB
> > ----------------------------------------------------------------- */ @@
> > -1990,6 +2004,14 @@ static const unsigned int hscif1_ctrl_b_pins[] = {
> > static const unsigned int hscif1_ctrl_b_mux[] = {
> > HRTS1_N_B_MARK, HCTS1_N_B_MARK,
> > };
> > +/* - I2C3
> > ------------------------------------------------------------------- */
> > +static const unsigned int i2c3_pins[] = {
> > + /* SCL, SDA */
> > + PIN_A_NUMBER('J', 15), PIN_A_NUMBER('H', 15),
> > +};
> > +static const unsigned int i2c3_mux[] = {
> > + I2C3_SCL_MARK, I2C3_SDA_MARK,
> > +};
> > /* - INTC
> > ------------------------------------------------------------------- */
> > static const unsigned int intc_irq0_pins[] = {
> > /* IRQ */
> > @@ -3047,6 +3069,7 @@ static const struct sh_pfc_pin_group pinmux_groups[] =
> > { SH_PFC_PIN_GROUP(hscif1_data_b),
> > SH_PFC_PIN_GROUP(hscif1_clk_b),
> > SH_PFC_PIN_GROUP(hscif1_ctrl_b),
> > + SH_PFC_PIN_GROUP(i2c3),
> > SH_PFC_PIN_GROUP(intc_irq0),
> > SH_PFC_PIN_GROUP(intc_irq1),
> > SH_PFC_PIN_GROUP(intc_irq2),
> > @@ -3243,6 +3266,10 @@ static const char * const hscif1_groups[] = {
> > "hscif1_ctrl_b",
> > };
> >
> > +static const char * const i2c3_groups[] = {
> > + "i2c3",
> > +};
> > +
> > static const char * const intc_groups[] = {
> > "intc_irq0",
> > "intc_irq1",
> > @@ -3469,6 +3496,7 @@ static const struct sh_pfc_function pinmux_functions[]
> > = { SH_PFC_FUNCTION(eth),
> > SH_PFC_FUNCTION(hscif0),
> > SH_PFC_FUNCTION(hscif1),
> > + SH_PFC_FUNCTION(i2c3),
> > SH_PFC_FUNCTION(intc),
> > SH_PFC_FUNCTION(mmc0),
> > SH_PFC_FUNCTION(mmc1),
> --
> Regards,
>
> Laurent Pinchart
>

---
Guennadi Liakhovetski, Ph.D.
Freelance Open-Source Software Developer
http://www.open-technology.de/


\
 
 \ /
  Last update: 2013-09-26 11:41    [W:0.250 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site