lkml.org 
[lkml]   [2013]   [Aug]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v8 2/3] DMA: Freescale: Add new 8-channel DMA engine device tree nodes
On 08/28/2013 08:51 PM, Mark Rutland wrote:
> On Wed, Aug 28, 2013 at 07:54:01AM +0100, Hongbo Zhang wrote:
>> On 08/27/2013 07:35 PM, Mark Rutland wrote:
>>> On Tue, Aug 27, 2013 at 11:42:02AM +0100, hongbo.zhang@freescale.com wrote:
>>>> From: Hongbo Zhang <hongbo.zhang@freescale.com>
>>>>
>>>> Freescale QorIQ T4 and B4 introduce new 8-channel DMA engines, this patch adds
>>>> the device tree nodes for them.
>>>>
>>>> Signed-off-by: Hongbo Zhang <hongbo.zhang@freescale.com>
>>>> ---
>>>> .../devicetree/bindings/powerpc/fsl/dma.txt | 66 ++++++++++++++++
>>>> arch/powerpc/boot/dts/fsl/b4si-post.dtsi | 4 +-
>>>> arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi | 81 ++++++++++++++++++++
>>>> arch/powerpc/boot/dts/fsl/elo3-dma-1.dtsi | 81 ++++++++++++++++++++
>>>> arch/powerpc/boot/dts/fsl/t4240si-post.dtsi | 4 +-
>>>> 5 files changed, 232 insertions(+), 4 deletions(-)
>>>> create mode 100644 arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi
>>>> create mode 100644 arch/powerpc/boot/dts/fsl/elo3-dma-1.dtsi
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt
>>>> index ddf17af..10fd031 100644
>>>> --- a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt
>>>> +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt
>>>> @@ -126,6 +126,72 @@ Example:
>>>> };
>>>> };
>>>>
>>>> +** Freescale Elo3 DMA Controller
>>>> + This is EloPlus controller with 8 channels, used in Freescale Txxx and Bxxx
>>>> + series chips, such as t1040, t4240, b4860.
>>>> +
>>>> +Required properties:
>>>> +
>>>> +- compatible : must include "fsl,elo3-dma"
>>>> +- reg : <registers specifier for DMA general status reg>
>>>> +- ranges : describes the mapping between the address space of the
>>>> + DMA channels and the address space of the DMA controller
>>>> +
>>>> +- DMA channel nodes:
>>>> + - compatible : must include "fsl,eloplus-dma-channel"
>>>> + - reg : <registers specifier for channel>
>>>> + - interrupts : <interrupt specifier for DMA channel IRQ>
>>>> + - interrupt-parent : optional, if needed for interrupt mapping
>>>> +
>>>> +Example:
>>>> +dma@100300 {
>>>> + #address-cells = <1>;
>>>> + #size-cells = <1>;
>>>> + compatible = "fsl,elo3-dma";
>>>> + reg = <0x100300 0x4 0x100600 0x4>;
>>> Is that one reg entry where #size-cells=2 and #address-cells=2?
>>>
>>> That's what the binding implies (given it only describes a single reg
>>> entry).
>>>
>>> if it's two entries, we should make that explicit (both in the binding
>>> and example):
>>>
>>> reg = <0x100300 0x4>,
>>> <0x100600 0x4>;
>> Yes they are two entries, I will change it this way.
> Ok. Could you make sure you document what the two reg entries correspond
> to? That's not clear from "<registers specifier for channel>".
Yes I am sure, we have reg for DMA controller and also reg for each DMA
channel.
these two reg entries are "registers specifier for DMA general status
reg", not "registers specifier for channel"
because this is an 8-channel DMA controller, we have two general status
registers (vs. one status register for 4-chanel DMA controller previously )
>>>> + ranges = <0x0 0x100100 0x500>;
>>> If it is one reg entry then the example ranges property isn't big enough
>>> to contain the parent-bus-address.
>> They are two reg entries, so the range is big enough.
> Ok.
>
>>>> + dma-channel@0 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x0 0x80>;
>>>> + interrupts = <28 2 0 0>;
>>>> + };
>>>> + dma-channel@80 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x80 0x80>;
>>>> + interrupts = <29 2 0 0>;
>>>> + };
>>>> + dma-channel@100 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x100 0x80>;
>>>> + interrupts = <30 2 0 0>;
>>>> + };
>>>> + dma-channel@180 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x180 0x80>;
>>>> + interrupts = <31 2 0 0>;
>>>> + };
>>>> + dma-channel@300 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x300 0x80>;
>>>> + interrupts = <76 2 0 0>;
>>>> + };
>>>> + dma-channel@380 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x380 0x80>;
>>>> + interrupts = <77 2 0 0>;
>>>> + };
>>>> + dma-channel@400 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x400 0x80>;
>>>> + interrupts = <78 2 0 0>;
>>>> + };
>>>> + dma-channel@480 {
>>>> + compatible = "fsl,eloplus-dma-channel";
>>>> + reg = <0x480 0x80>;
>>>> + interrupts = <79 2 0 0>;
>>>> + };
>>>> +};
>>>> +
>>>> Note on DMA channel compatible properties: The compatible property must say
>>>> "fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA
>>>> driver (fsldma). Any DMA channel used by fsldma cannot be used by another
>>>> diff --git a/arch/powerpc/boot/dts/fsl/b4si-post.dtsi b/arch/powerpc/boot/dts/fsl/b4si-post.dtsi
>>>> index 7399154..ea53ea1 100644
>>>> --- a/arch/powerpc/boot/dts/fsl/b4si-post.dtsi
>>>> +++ b/arch/powerpc/boot/dts/fsl/b4si-post.dtsi
>>>> @@ -223,13 +223,13 @@
>>>> reg = <0xe2000 0x1000>;
>>>> };
>>>>
>>>> -/include/ "qoriq-dma-0.dtsi"
>>>> +/include/ "elo3-dma-0.dtsi"
>>>> dma@100300 {
>>>> fsl,iommu-parent = <&pamu0>;
>>>> fsl,liodn-reg = <&guts 0x580>; /* DMA1LIODNR */
>>>> };
>>>>
>>>> -/include/ "qoriq-dma-1.dtsi"
>>>> +/include/ "elo3-dma-1.dtsi"
>>>> dma@101300 {
>>>> fsl,iommu-parent = <&pamu0>;
>>>> fsl,liodn-reg = <&guts 0x584>; /* DMA2LIODNR */
>>>> diff --git a/arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi b/arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi
>>>> new file mode 100644
>>>> index 0000000..69a3277
>>>> --- /dev/null
>>>> +++ b/arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi
>>>> @@ -0,0 +1,81 @@
>>>> +/*
>>>> + * QorIQ DMA device tree stub [ controller @ offset 0x100000 ]
>>> Copy-pasted?
>>>
>>> Presumably should be "Elo3 DMA devicetree stub", or similar?
>>>
>>> Similarly for elo3-dma-1.dtsi.
>> Yes copy-pasted, but QorIQ isn't wrong, it is name of Freescale series
>> chips.
>> To be more specific, I'd like to use "QorIQ Elo3 DMA devicetree stub"
> That sounds good to me.
>
> Cheers,
> Mark.
>





\
 
 \ /
  Last update: 2013-08-29 05:01    [W:0.070 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site