lkml.org 
[lkml]   [2013]   [Jul]   [5]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH V2 1/8] regulator: Introduce OMAP regulator to control PMIC over VC/VP
On 07/05/2013 09:08 AM, Mark Brown wrote:
> On Fri, Jul 05, 2013 at 08:55:07AM -0500, Nishanth Menon wrote:
>
> Please write in paragraphs, an enormous wall of unbroken text isn't
> helpful for legibility.

Apologies on the same. Will try to do better.

>
>> On 16:41-20130704, Mark Brown wrote:
>
>>> So, this still has the thing where all the data about the PMIC is
>>> replicated (but now in this driver). It should be possible to pull all
>>> the above information except possibly the I2C timeout and perhaps the
>>> I2C address (if there's a separate control interface) from the standard
>>> regulator core data structures for the PMIC. This would allow the
>>> driver to Just Work with any PMIC without needing to add it in two
>>> places.
>
>> option 1) we just bypass get_voltage/set_voltage to point through to
>> this function. result will be something similar to what we got here[1]
>
> I don't really know what you mean when you say "bypass get_voltage/set_voltage
> so it's kind of hard to comment... the link you posted appears to be a
> link to the code I'm reviewing so it's not terribly enlightening.

:) it is similar, yes. by bypass get/set_voltage, I mean something like [1]

>
>> Again, based on this discussion, it is wrong - and we already did implement
>> the *wrong* way in OMAP and the new code is supposed to throw away the
>> old code once all relevant platforms are converted to DT.
>> - now, we could improve this by passing rdev and slurp out required
>> data from regulator structures, but obviously, as you pointed out, it wont
>> be sufficient.
>> - In this solution, we will have existing regulator drivers supporting
>> additional data path. *but* that also means that existing regulator
>> drivers will need to be modified to handle multiple data path and "Just
>> Work" wont happen - so not really good other than screw up existing
>> regulator drivers with handling OMAP specific APIs in them.
>
> What makes you think that the existing regulator drivers need to be
> modified?


data path difference - Almost all standard regulators use i2c (standard
i2c APIs) for every other SMPS/LDO except for the ones controlled by
OMAP custom i2c path(vc/vp), the set_voltage/get_voltage needs a
different implementation when it comes to using the vc/vp path.

> They already have all the data exported to the core (or
> should do)...

I see that twl-regulator does not indeed do it, but, assuming the
regulators have all the data exported to the core, the data is hidden in
struct regulator_desc which is private to the device and driver. lets go
through these:

> +static const struct omap_pmic_info omap_twl4030_vdd1 = {
> + .slave_addr = 0x12,
Not readily exposed, but we can solve that using reg=<0x12>; in dts -
this might not be duplication as the register address will be unique for
the bus.

> + .voltage_reg_addr = 0x00,
desc->vsel_reg maps fine

> + .cmd_reg_addr = 0x00,
command register is used for sending low power state commands - which is
not the same as voltage register or vsel_reg as used in depicted in
regulator_desc.

> + .i2c_timeout_us = 200,
yep, does not match up.

> + .slew_rate_uV = 4000,
desc->ramp_delay maps fine

> + .step_size_uV = 12500,
desc->uV_step maps fine.

> + .min_uV = 600000,
desc->min_uV maps fine.

> + .max_uV = 1450000,
can be used with constraints, but most regulator drivers seem to store
this internally.

> + .voltage_selector_offset = 0,
> + .voltage_selector_mask = 0x7F,
> + .voltage_selector_setbits = 0x0,
> + .voltage_selector_zero = false,
to an extent we can map these to vsel_mask, linear_min_sel etc. (again
assuming the regulator driver has populated it - most that implement
custom set_voltage, get_voltage do not do that.

Now, How do you suggest I pick up this data in omap_pmic regulator?
linux/regulator/consumer.h does not seem appropriate omap_pmic is not
really a consumer of the regulator and further all the detailed data is
not exposed either.

Other option is to make rdev available to omap_pmic regulator - which
again implies change in existing regulator driver?


> the only thing that's missing is the timeouts and it's
> not at all obvious why those need to be tuned per device.

OMAP VC hardware has no idea about how long to wait before giving up on
an ongoing i2c transaction. This may depend on PMIC and what it does
before acking on i2c.

>
>> option 2) make omap_pmic regulator use twl_regulator - regulator
>> chaining.
>
> Again I don't know what this is.
Lets ignore this for the moment.


[1]
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=63bfff4e20211b464cbea6e79e5fd36df227c154
--
Regards,
Nishanth Menon


\
 
 \ /
  Last update: 2013-07-05 18:01    [W:0.071 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site