lkml.org 
[lkml]   [2013]   [Jul]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC v3 3/3] saa7115: Implement i2c_board_info.platform_data
Hi Hans,

Seems I've had some trouble with my mailserver that caused your message to bounce.
I had to download your email from a mailinglist archive.

On Wed, Jul 03, 2013 at 10:27:20PM -0000, hans.verkuil@cisco.com wrote:
> Hi Jon Arne,
>
> Patches 1 & 2 look good to me. But I do have a few comments for this one:
>
> On 07/04/2013 01:27 AM, Jon Arne J?rgensen wrote:
> > Implement i2c_board_info.platform_data handling in the driver so we can
> > make device specific changes to the chips we support.
> >
> > I'm adding a new init table for the gm7113c chip because the old saa7113
> > init table has a illegal and wrong defaults according to the datasheet.
> >
> > I'm also adding an option to the platform_data struct to choose the gm7113c_init
> > table even if you are writing a driver for the saa7113 chip.
> >
> > This implementation is only adding overrides for the SAA7113 and GM7113C chips.
> >
> > Signed-off-by: Jon Arne J?rgensen <jonarne@xxxxxxxxxx>
> > ---
> > drivers/media/i2c/saa7115.c | 144 ++++++++++++++++++++++++++++++++++++---
> > drivers/media/i2c/saa711x_regs.h | 15 ++++
> > include/media/saa7115.h | 65 ++++++++++++++++++
> > 3 files changed, 215 insertions(+), 9 deletions(-)
> >

[SNIP]

> > +/* SAA7113 Init codes */
> > static const unsigned char saa7113_init[] = {
> > R_01_INC_DELAY, 0x08,
> > R_02_INPUT_CNTL_1, 0xc2,
> > R_03_INPUT_CNTL_2, 0x30,
> > R_04_INPUT_CNTL_3, 0x00,
> > R_05_INPUT_CNTL_4, 0x00,
> > - R_06_H_SYNC_START, 0x89,
> > + R_06_H_SYNC_START, 0x89, /* Illegal value - min. value = 0x94 */
> > + R_07_H_SYNC_STOP, 0x0d,
> > + R_08_SYNC_CNTL, 0x88, /* OBS. HTC = VTR Mode - Not default */
>
> Can you mention the correct default in the comment?
>
> > + R_09_LUMA_CNTL, 0x01,
> > + R_0A_LUMA_BRIGHT_CNTL, 0x80,
> > + R_0B_LUMA_CONTRAST_CNTL, 0x47,
> > + R_0C_CHROMA_SAT_CNTL, 0x40,
> > + R_0D_CHROMA_HUE_CNTL, 0x00,
> > + R_0E_CHROMA_CNTL_1, 0x01,
> > + R_0F_CHROMA_GAIN_CNTL, 0x2a,
> > + R_10_CHROMA_CNTL_2, 0x08, /* Not datasheet default */
>
> Ditto.
>
> > + R_11_MODE_DELAY_CNTL, 0x0c,
> > + R_12_RT_SIGNAL_CNTL, 0x07, /* Not datasheet default */
>
> Ditto.
>
> > + R_13_RT_X_PORT_OUT_CNTL, 0x00,
> > + R_14_ANAL_ADC_COMPAT_CNTL, 0x00,
> > + R_15_VGATE_START_FID_CHG, 0x00,
> > + R_16_VGATE_STOP, 0x00,
> > + R_17_MISC_VGATE_CONF_AND_MSB, 0x00,
> > +
> > + 0x00, 0x00
> > +};

[SNIP]

> > + if (data->saa7113_r08_htc) {
> > + work = saa711x_read(sd, R_08_SYNC_CNTL);
> > + work &= ~SAA7113_R_08_HTC_MASK;
> > + work |= ((*data->saa7113_r08_htc) << SAA7113_R_08_HTC_OFFSET);
> > + if (*data->saa7113_r08_htc != SAA7113_HTC_RESERVED) {
> > + v4l2_dbg(1, debug, sd,
> > + "set R_08 HTC [Mask 0x%02x] [Value 0x%02x]\n",
> > + SAA7113_R_08_HTC_MASK, *data->saa7113_r08_htc);
>
> I would leave out the check against RESERVED (see also my comment later in the
> header) and the debug messages in this function. You can always dump the registers
> with v4l2-dbg, so I don't think they add a lot.
>
> > + saa711x_write(sd, R_08_SYNC_CNTL, work);
> > + }
> > + }
> > +
> > + if (data->saa7113_r10_vrln) {
> > + work = saa711x_read(sd, R_10_CHROMA_CNTL_2);
> > + work &= ~SAA7113_R_10_VRLN_MASK;
> > + if (*data->saa7113_r10_vrln)
> > + work |= (1 << SAA7113_R_10_VRLN_OFFSET);
> > +
> > + v4l2_dbg(1, debug, sd,
> > + "set R_10 VRLN [Mask 0x%02x] [Value 0x%02x]\n",
> > + SAA7113_R_10_VRLN_MASK, *data->saa7113_r10_vrln);
> > + saa711x_write(sd, R_10_CHROMA_CNTL_2, work);
> > + }
> > +
> > + if (data->saa7113_r10_ofts) {
> > + work = saa711x_read(sd, R_10_CHROMA_CNTL_2);
> > + work &= ~SAA7113_R_10_OFTS_MASK;
> > + work |= (*data->saa7113_r10_ofts << SAA7113_R_10_OFTS_OFFSET);
> > + v4l2_dbg(1, debug, sd,
> > + "set R_10 OFTS [Mask 0x%02x] [Value 0x%02x]\n",
> > + SAA7113_R_10_OFTS_MASK, *data->saa7113_r10_ofts);
> > + saa711x_write(sd, R_10_CHROMA_CNTL_2, work);
> > + }
> > +
> > + if (data->saa7113_r12_rts0) {
> > + work = saa711x_read(sd, R_12_RT_SIGNAL_CNTL);
> > + work &= ~SAA7113_R_12_RTS0_MASK;
> > + work |= (*data->saa7113_r12_rts0 << SAA7113_R_12_RTS0_OFFSET);
> > + if (*data->saa7113_r12_rts0 != SAA7113_RTS_DOT_IN) {
>
> I would replace this with a WARN_ON and add a comment as well.
>
> > + v4l2_dbg(1, debug, sd,
> > + "set R_12 RTS0 [Mask 0x%02x] [Value 0x%02x]\n",
> > + SAA7113_R_12_RTS0_MASK,
> > + *data->saa7113_r12_rts0);
> > + saa711x_write(sd, R_12_RT_SIGNAL_CNTL, work);
> > + }
> > + }
> > +

[SNIP]

> > +/* Register 0x08 "Horizontal time constant" [Bit 3..4]:
> > + * Should be set to "Fast Locking Mode" according to the datasheet,
> > + * and that is the default setting in the gm7113c_init table.
> > + * saa7113_init sets this value to "VTR Mode". */
> > +enum saa7113_r08_htc {
> > + SAA7113_HTC_TV_MODE = 0x00,
> > + SAA7113_HTC_VTR_MODE, /* Default for saa7113_init */
> > + SAA7113_HTC_RESERVED, /* DO NOT USE */
>
> If it shouldn't be used, then it shouldn't be defined :-) So drop it,
>
> > + SAA7113_HTC_FAST_LOCKING_MODE /* Default for gm7113c_init */
>
> and instead use this:
>
> SAA7113_HTC_FAST_LOCKING_MODE = 0x03 /* Default for gm7113c_init */
>
> > +};
> > +

[SNIP]

>
> Regards,
>
> Hans
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html

I'll fix the patch according to your comments.
Thanks for the review.

Best regards,
Jon Arne



\
 
 \ /
  Last update: 2013-07-30 14:01    [W:0.055 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site