lkml.org 
[lkml]   [2013]   [Jul]   [27]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 2/3] ACPI / PM: Make messages in acpi_device_set_power() print device names
Date
From: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Modify acpi_device_set_power() so that diagnostic messages printed by
it to the kernel log always contain the name of the device concerned
to make it possible to identify the device that triggered the message
if need be.

Also replace printk(KERN_WARNING ) with dev_warn() everywhere in that
function.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
---
drivers/acpi/device_pm.c | 22 ++++++++++------------
1 file changed, 10 insertions(+), 12 deletions(-)

Index: linux-pm/drivers/acpi/device_pm.c
===================================================================
--- linux-pm.orig/drivers/acpi/device_pm.c
+++ linux-pm/drivers/acpi/device_pm.c
@@ -166,20 +166,20 @@ int acpi_device_set_power(struct acpi_de
/* Make sure this is a valid target state */

if (state == device->power.state) {
- ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Device is already at %s\n",
+ ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Device [%s] already in %s\n",
+ device->pnp.bus_id,
acpi_power_state_string(state)));
return 0;
}

if (!device->power.states[state].flags.valid) {
- printk(KERN_WARNING PREFIX "Device does not support %s\n",
- acpi_power_state_string(state));
+ dev_warn(&device->dev, "Power state %s not supported\n",
+ acpi_power_state_string(state));
return -ENODEV;
}
if (device->parent && (state < device->parent->power.state)) {
- printk(KERN_WARNING PREFIX
- "Cannot set device to a higher-powered"
- " state than parent\n");
+ dev_warn(&device->dev, "Cannot transition to a higher-powered "
+ "state than parent\n");
return -ENODEV;
}

@@ -192,8 +192,8 @@ int acpi_device_set_power(struct acpi_de

if (state < device->power.state && state != ACPI_STATE_D0
&& device->power.state >= ACPI_STATE_D3_HOT) {
- printk(KERN_WARNING PREFIX
- "Cannot transition to non-D0 state from D3\n");
+ dev_warn(&device->dev,
+ "Cannot transition to non-D0 state from D3\n");
return -ENODEV;
}

@@ -220,10 +220,8 @@ int acpi_device_set_power(struct acpi_de

end:
if (result) {
- printk(KERN_WARNING PREFIX
- "Device [%s] failed to transition to %s\n",
- device->pnp.bus_id,
- acpi_power_state_string(state));
+ dev_warn(&device->dev, "Failed to change power state to %s\n",
+ acpi_power_state_string(state));
} else {
device->power.state = state;
ACPI_DEBUG_PRINT((ACPI_DB_INFO,


\
 
 \ /
  Last update: 2013-07-27 15:21    [W:0.133 / U:0.428 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site