lkml.org 
[lkml]   [2013]   [Jul]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 2/2] media: i2c: tvp7002: add OF support
On Fri, Jul 12, 2013 at 3:34 AM, Sylwester Nawrocki
<sylvester.nawrocki@gmail.com> wrote:
> On 07/11/2013 07:09 PM, Prabhakar Lad wrote:
> [...]
>
>>>> diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
>>>> b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
>>>> new file mode 100644
>>>> index 0000000..9daebe1
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
>>>> @@ -0,0 +1,43 @@
>>>> +* Texas Instruments TV7002 video decoder
>>>> +
>
> [...]
>
>>>> +
>>>> +- ti,tvp7002-fid-polarity: Active-high Field ID polarity of the
>>>> endpoint.
>>>
>>>
>>> I thought it was agreed 'field-even-active' would be used instead of
>>> this device specific property. Did you run into any issues with that ?
>>>
>>>
>> Argh I some how missed it out, sorry this should be 'field-even-active'
>
>
> OK.
>
>
>>> And include/media/tvp70002.h:
>>>
>>> * fid_polarity:
>>> * 0 -> the field ID output is set to logic 1 for
>>> an
>>> odd
>>> * field (field 1) and set to logic 0 for an
>>> even
>>> * field (field 0).
>>> * 1 -> operation with polarity inverted.
>>>
>>>
>>> Do you know if the chip automatically selects video sync source
>>> (sync-on-green
>>> vs. VSYNC/HSYNC) and there is no need to configure this on the analogue
>>> input
>>> side ? At least the driver seems to always select the default SOGIN_1
>>> input
>>> (TVP7002_IN_MUX_SEL_1 register is set only at initialization time).
>>>
>> Yes the driver is selecting the default SOGIN_1 input.
>>
>>> Or perhaps it just outputs on SOGOUT, VSOUT, HSOUT lines whatever is fed
>>> to
>>> its analogue inputs, and any further processing unit need to determine
>>> what
>>> synchronization signal is present and should be used ?
>>>
>>
>> Yes that correct, there is a register (Sync Detect Status) which
>> detects the sync for you.
>>
>>> I suspect that we don't need, e.g. another endpoint node to specify the
>>> configuration of the TVP7002 analogue input interface, that would contain
>>> a property like video-sync.
>>>
>>>
>> If I understand correctly you mean if there are two tvp7002 devices
>> connected
>> we don’t need to specify video-sync property, but my question how do we
>> specify this property in common then ?
>
>
> No, I thought about two port sub-nodes of a single device node, one for the
> TVP7002 video input and one for the output. But it seems there is no need
> for that, i.e. to specify the input configuration statically in the
> firmware.
> The chip detects the signals automatically, i.e. it uses whatever is
> available,
> and it allows querying the selection status at run time. What would really
> need to be configured statically in DT in that case then ? Some initial
> video
> sync configuration ? I guess it could be well hard coded in the driver,
> since
> the hardware does run time detection anyway.
>
Yes the chip detects the signal automatically, What I want to configure in
the DT case is say if SOG signal is detected, I want to invert the polarity
of it this is what I am trying to set in DT case whether to invert or not.
0 = Normal operation (default)
1 = SOG output polarity inverted

Something similar to fid_polarity.

Regards,
--Prabhakar Lad
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

\
 
 \ /
  Last update: 2013-07-12 07:22    [W:0.091 / U:0.708 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site