lkml.org 
[lkml]   [2013]   [Oct]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC] clk: add flags to distinguish xtal clocks
From
Date
On Wed, 2013-10-23 at 02:24 -0700, Mike Turquette wrote:
> Quoting Luca Coelho (2013-10-16 03:24:27)
> > Hi,
> >
> > Sorry for the delayed response.
> >
> > On Tue, 2013-10-08 at 10:27 -0500, Felipe Balbi wrote:
> > > Fixing Luca's address since he left TI
> >
> > Thanks, Felipe! I wouldn't have seen this otherwise.
> >
> >
> > > On Mon, Oct 07, 2013 at 12:44:24AM -0700, Mike Turquette wrote:
> > > > Quoting Luciano Coelho (2013-07-29 06:50:42)
> > > > > Hi Mike,
> > > > >
> > > > > On Fri, 2013-07-05 at 10:54 +0300, Luciano Coelho wrote:
> > > > > > On Thu, 2013-07-04 at 16:19 -0700, Mike Turquette wrote:
> > > > > > > Quoting Luciano Coelho (2013-07-04 15:37:45)
> > > > > > > > On Thu, 2013-07-04 at 15:25 -0700, Mike Turquette wrote:
> > > > > > > > > Or is it the same clock input and basically the problem is that you need
> > > > > > > > > to know what kind of waveform to expect (e.g. square versus sine)?
> > > > > > > >
> > > > > > > > It's the same clock input in the chip's perspective. One clock input
> > > > > > > > that can be any of the combinations I mentioned above. Again, I'm not
> > > > > > > > familiar with clocks, so I guess the square vs. sine explanation is
> > > > > > > > plausible. What I could see in the firmware is that it handles the
> > > > > > > > clocks differently if they're xtal or not.
> > > > > > >
> > > > > > > OMAP has a similar thing where sys_clkin (the fast reference clock for
> > > > > > > the chip) can be 19.2, 26, 38.4, etc. This is easy to handle since only
> > > > > > > the rates matter.
> > > > > >
> > > > > > Right, this part is easy and I already have the code for that. What I'm
> > > > > > missing is a way to pass this XTAL flag to the chip.
> > > > > >
> > > > > >
> > > > > > > In your case you need some extra metadata to know what to do. I'm really
> > > > > > > not sure if CLK_IS_TYPE_XTAL is the most useful form this metadata can
> > > > > > > take. It would be best to know if the waveform is what you really need
> > > > > > > to know, or perhaps something else. For instance you might be affected
> > > > > > > by some clock signal stabilization time. Can you talk to your hardware
> > > > > > > guys and figure it out? I'd rather model the actual needs instead of
> > > > > > > just tossing a flag in there.
> > > > > >
> > > > > > I get your point. I have tried to investigate how this flag is used by
> > > > > > the firmware and I could see that it is used to set different "buffer
> > > > > > gains" and "delays" when waking up (I guess this means when the clock is
> > > > > > starting, so probably related to stabilization time). They specify two
> > > > > > "modes", "boost" and "normal" and use different delay values for each.
> > > > >
> > > > > I tried but I couldn't find any more information on how exactly this
> > > > > works. But since this change is really simple and there seems to be
> > > > > other people who need the same information, couldn't we add it as is and
> > > > > try to figure out more specific information about the clocks later on?
> > > > >
> > > > > Even if XTAL is not that useful if we know the other details, at least
> > > > > it wouldn't hurt to have the flag there anyway.
> > > >
> > > > Luca,
> > > >
> > > > By any chance did you come to a different solution for this problem? I
> > > > can take the patch, but I do not feel like we're solving the right
> > > > problem the right way.
> >
> > Unfortunately I didn't find any better solution for this. From the
> > WiLink firmware's point of view, there was not much information about
> > the details of stabilization time requirements and such.
> >
> >
> > > > If not I will take it for 3.13.
> >
> > That would be great! As I mentioned above, the XTAL/non-XTAL flag
> > wouldn't hurt, even if in most cases it may not provide the necessary
> > details for the clock code. But at least for the WiLink hardware it is
> > very useful. ;)
>
> Why is the CLK_IS_TYPE_DEFINED necessary?

This is just for backwards compatibility. Currently all the other
clocks don't set the XTAL/non-XTAL flag (even if they *are* XTAL), so if
the CLK_IS_TYPE_DEFINED is not set, we know we can't trust the
XTAL/no-XTAL flag.


> Also we're adding a property to the fixed-rate binding so
> Documentation/devicetree/bindings/clock/fixed-clock.txt needs to be
> updated.

Yeah, you're right. Unfortunately, I won't have the time to resubmit
this patch any time soon. :(

--
Luca.



\
 
 \ /
  Last update: 2013-10-23 14:01    [W:0.106 / U:0.268 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site