lkml.org 
[lkml]   [2012]   [Sep]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [RFC 1/3] PCI/PM: Fix kexec for D3cold and bridge suspending
From
Date
On Thu, 2012-09-20 at 00:38 -0700, Eric W. Biederman wrote:
> Bjorn Helgaas <bhelgaas@google.com> writes:
>
> > +cc Eric and kexec list
> >
> > On Mon, Sep 17, 2012 at 2:54 AM, Huang Ying <ying.huang@intel.com> wrote:
> >> If PCI devices are put into D3cold before kexec, because the
> >> configuration registers of PCI devices in D3cold are not accessible.
> >>
> >> And if PCI bridges are put into low power state before kexec,
> >> configuration registers of PCI devices underneath the PCI bridges are
> >> not accessible too.
> >>
> >> These will make some PCI devices can not be scanned after kexec, so
> >> resume the PCI devices in D3cold or PCI bridges in low power state
> >> before kexec.
> >
> > Don't we need to resume the device even without the kexec issue? And
> > even if it's in D1 or D2?
>
> The basic requirement is that the device needs to be visible so we can
> auto discover it. As I recall most sleep states don't make the device
> invisible and we can handle the rest in the device initializatoin code.

PCI devices in D3cold or under a bridge in D3hot will not be visible, so
we must fix that for kexec to run properly.

> > It looks to me like pci_msi_shutdown() (and probably drv->shutdown())
> > depend on the device being in D0.
>
> There is certainly a depenency on the config registers being visible.
> Although I don't know if much will go wrong if they aren't.
>
> Ceratinly pci_msi_shutdown doesn't have anything to do if the device has
> had so much power removed that the device is not even exectuing.

Don't know which power state device should be in for pci_msi_shutdown
etc. But it appears that normal shutdown/reboot and kexec works at most
times so far. D3cold and bridge in D3hot works for normal
shutdown/reboot, but not for kexec. So I write some fix.

Best Regards,
Huang Ying

> >> Signed-off-by: Huang Ying <ying.huang@intel.com>
> >> ---
> >> drivers/pci/pci-driver.c | 4 ++++
> >> 1 file changed, 4 insertions(+)
> >>
> >> --- a/drivers/pci/pci-driver.c
> >> +++ b/drivers/pci/pci-driver.c
> >> @@ -421,6 +421,10 @@ static void pci_device_shutdown(struct d
> >> struct pci_dev *pci_dev = to_pci_dev(dev);
> >> struct pci_driver *drv = pci_dev->driver;
> >>
> >> + /* Resume bridges and devices in D3cold for kexec to work properly */
> >> + if (pci_dev->current_state == PCI_D3cold || pci_dev->subordinate)
> >> + pm_runtime_resume(dev);
> >> +
> >> if (drv && drv->shutdown)
> >> drv->shutdown(pci_dev);
> >> pci_msi_shutdown(pci_dev);
> >
> > _______________________________________________
> > kexec mailing list
> > kexec@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/kexec




\
 
 \ /
  Last update: 2012-09-20 11:01    [W:0.074 / U:0.852 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site