lkml.org 
[lkml]   [2012]   [Sep]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6] iio: adc: add new lp8788 adc driver
On 09/18/2012 09:19 AM, Lars-Peter Clausen wrote:
> On 09/17/2012 11:35 AM, Kim, Milo wrote:
>> TI LP8788 PMU provides regulators, battery charger, ADC,
>> RTC, backlight driver and current sinks.
>>
>> This patch enables the LP8788 ADC functions.
>>
>> The LP8788 ADC has several ADC input selection and supports 12bit resolution.
>> Internal operation of getting ADC is access to registers of LP8788.
>> The LP8788 ADC uses exported functions for accessing these registers.
>> (exported by LP8788 MFD device driver)
>>
>> This driver supports IIO_CHAN_INFO_RAW and SCALE.
>> So the IIO consumer can calculate the value with raw and scale.
>> The unit of scale is micro.
>>
>> (ADC Input Selection)
>>
>> Voltage: battery voltage (MAX 5.0, 5.5 and 6.0V)
>> charger input voltage
>> four general ADC inputs
>> coin cell voltage
>> Current: battery charging current
>> Temperature: IC temperature
>>
>> (The IIO map for the IIO consumer)
>>
>> The ADC input is configurable in the platform side.
>> Even though this platform data is not defined,
>> the default IIO map is created for supporting the power supply driver.
>> The battery voltage and temperature are used inside this driver.
>>
>> (History)
>>
>> Patch v6.
>> (a) Fix scale value for each ADC input selection
>> Voltage and current type are mili unit and temperature is degree.
>> To calculate the IC temperature,
>> temp = raw * scaleint + (raw * scalepart)/ 1000000, scaleint is always 0.
>> = raw * 0.061050, raw: 0 ~ 4095
>> Then range of IC temperature(ADC result) is 0 ~ 250'C
>>
>> (b) Reorganization of the IIO channel Spec
>> Remove address, scan_type and scan_index and rollback the datasheet name.
>> The reason why 'address' field is unnecessary is no relation with each channel.
>> Moreover, to get the raw ADC value, the address info is not only one register
>> but also several registers.
>> Therefore specific function(lp8788_get_adc_result) is called rather than
>> using one 'address' field.
>>
>> (c) Fix coding style
>> Remove duplicated checking routine while unregistering the IIO map.
>> Fix code for space and parenthesis.
>>
>> Patch v5.
>> Fix default consumer name as 'lp8788-charger'.
>> Add mutex for ADC read operation.
>> Reorganization on lp8788_adc_read_raw().
>>
>> Patch v4.
>> Fix adc_raw function: support RAW and SCALE channel info.
>> Change LP8788 ADC platform data - iio map.
>> Enables the default IIO map.
>>
>> Patch v3.
>> Fix wrong size of allocating iio private data.
>> Fix coding styles.
>>
>> Patch v2.
>> Support RAW and SCALE interface for IIO consumer.
>> Clean up the iio channel spec macro.
>>
>> Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
>
> Looks good to me,
>
> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
I've added this to my local tree but not pushed out just
yet on basis you might want to change the behaviour Lars
has pointed out...

I don't here it'll go as is in a day or so.

Jonathan
>
> One comment though, not sure if it is critical or not.
>
>> +static int lp8788_get_adc_result(struct lp8788_adc *adc, enum lp8788_adc_id id,
>> + int *val)
>> +{
>> + unsigned int msb;
>> + unsigned int lsb;
>> + unsigned int result;
>> + u8 data;
>> + u8 rawdata[2];
>> + int size = ARRAY_SIZE(rawdata);
>> + int retry = 5;
>> + int ret;
>> +
>> + data = (id << 1) | ADC_CONV_START;
>> + ret = lp8788_write_byte(adc->lp, LP8788_ADC_CONF, data);
>> + if (ret)
>> + goto err_io;
>> +
>> + /* retry until adc conversion is done */
>> + data = 0;
>> + while (retry--) {
>> + usleep_range(100, 200);
>> +
>> + ret = lp8788_read_byte(adc->lp, LP8788_ADC_DONE, &data);
>> + if (ret)
>> + goto err_io;
>> +
>> + /* conversion done */
>> + if (data)
>> + break;
>
> Could as well go into the while header like this:
> while (!data && retry--)
>
>> + }
>> +
>
> You still sample the data, even if there was a timeout and ADC_DONE is not set.
>
>> + ret = lp8788_read_multi_bytes(adc->lp, LP8788_ADC_RAW, rawdata, size);
>> + if (ret)
>> + goto err_io;
>> +
>> + msb = (rawdata[0] << 4) & 0x00000ff0;
>> + lsb = (rawdata[1] >> 4) & 0x0000000f;
>> + result = msb | lsb;
>> + *val = result;
>> +
>> + return 0;
>> +
>> +err_io:
>> + return ret;
>> +}


\
 
 \ /
  Last update: 2012-09-18 23:41    [W:0.065 / U:0.028 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site