lkml.org 
[lkml]   [2012]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [RFC PATCH 05/14] PCI: add access functions for PCIe capabilities to hide PCIe spec differences
On Sun, Jul 15, 2012 at 10:47 AM, Jiang Liu <liuj97@gmail.com> wrote:
> On 07/13/2012 04:49 AM, Bjorn Helgaas wrote:
>>> Hi Bjorn,
>>> It's a little risk to change these PCIe capabilities access
>>> functions as void. On some platform with hardware error detecting/correcting
>>> capabilities, such as EEH on Power, it would be better to return
>>> error code if hardware error happens during accessing configuration registers.
>>> As I know, coming Intel Xeon processor may provide PCIe hardware
>>> error detecting capability similar to EEH on power.
>>
>> I guess I'm playing devil's advocate here. As a general rule, people
>> don't check the return value of pci_read_config_*() or
>> pci_write_config_*(). Unless you change them all, most callers of
>> pci_pcie_capability_read_*() and _write_*() won't check the returns
>> either. So I'm not sure return values are an effective way to detect
>> those hardware errors.
>>
>> How do these EEH errors get detected or reported today? Do the
>> drivers check every config access for success? Adding those checks
>> and figuring out how to handle errors at every possible point doesn't
>> seem like a recipe for success.
>
> Hi Bjorn,
> Sorry for later reply, on travel these days.
> Yeah, it's true that most driver doesn't check return values of configuration
> access functions, but there are still some drivers which do check return value of
> pci_read_config_xxx(). For example, pciehp driver checks return value of CFG access
> functions.
>
> It's not realistic to enhance all drivers, but we may focus on a small set of
> drivers for hardwares on specific high-end servers. For RAS features, we can never provide
> perfect solutions, so we prefer some improvements. After all a small improvement is still
> an improvement:)
>
> I'm only familiar with PCI on IA64 and x86. For PowerPC, I just know that the OS
> may query firmware whether there's some hardware faults if pci_cfg_read_xxx() returns
> all 1s. For PCI on IA64, SAL may handle PCI hardware errors and return error code to
> pci_cfg_read_xxx(). For x86, I think it will have some mechanisms to report hardware faults
> like SAL on IA64.
>
> So how about keeping consistence with pci_cfg_read_xxx() and pci_user_cfg_read_xxx()?

My goal is "the caller should never have to know whether this is a v1
or v2 capability." Returning any error other than one passed along
from pci_read/write_config_xxx() means we miss that goal. Perhaps the
goal is unattainable, but I haven't been convinced yet.

I think hardware error detection is irrelevant to this discussion.
After reading Documentation/PCI/pci-error-recovery.txt, I'm even less
convinced that checking return values from pci_read/write_config_xxx()
or pci_pcie_capability_read/write_xxx() is a useful way to detect
hardware errors.

Having drivers detect hardware failures by checking for config access
errors is neither necessary nor sufficient. It's not necessary
because a platform can implement a config accessor that checks *every*
access and reports failures to the driver via the pci_error_handler
framework. It's not sufficient because config accesses are rare
(usually only at init-time), and hardware failures may happen at
arbitrary other times.

In my opinion, the only relevant question is whether a caller of
pci_pcie_capability_read/write_xxx() needs to know whether a register
is implemented (i.e., we have a v2 capability) or not. For reads, I
don't think there's a case where fabricating a value of zero when
reading an unimplemented register is a problem.

Writes are obviously more interesting, but I'm still not sure there's
a case where silently dropping a write to an unimplemented register is
a problem. The "capability" registers are read-only, so there's no
problem if we drop writes to them. The "status" registers are
generally RO or RW1C, where it's only meaningful to write a non-zero
value if you're previously *read* a non-zero value. The "control"
registers are often RW, of course, but generally it's only meaningful
to write a non-zero value when a non-zero bit in the "capability"
register has previously told you that something is supported.

Bjorn


\
 
 \ /
  Last update: 2012-07-16 20:21    [W:0.092 / U:0.860 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site