lkml.org 
[lkml]   [2012]   [Jul]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH] irq_domain: Standardise legacy/linear domain selection
Date
On Thu,  5 Jul 2012 12:19:19 +0100, Mark Brown <broonie@opensource.wolfsonmicro.com> wrote:
> A large proportion of interrupt controllers that support legacy mappings
> do so because non-DT systems need to use fixed IRQ numbers when registering
> devices via buses but can otherwise use a linear mapping. The interrupt
> controller itself typically is not affected by the mapping used and best
> practice is to use a linear mapping where possible so drivers frequently
> select at runtime depending on if a legacy range has been allocated to
> them.
>
> Standardise this behaviour by providing irq_domain_register_simple() which
> will allocate a linear mapping unless a positive first_irq is provided in
> which case it will fall back to a legacy mapping. This helps make best
> practice for irq_domain adoption clearer.
>
> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Applied, thanks.

g.

> ---
> Documentation/IRQ-domain.txt | 5 +++++
> include/linux/irqdomain.h | 5 +++++
> kernel/irq/irqdomain.c | 30 ++++++++++++++++++++++++++++++
> 3 files changed, 40 insertions(+)
>
> diff --git a/Documentation/IRQ-domain.txt b/Documentation/IRQ-domain.txt
> index 27dcaab..1401cec 100644
> --- a/Documentation/IRQ-domain.txt
> +++ b/Documentation/IRQ-domain.txt
> @@ -93,6 +93,7 @@ Linux IRQ number into the hardware.
> Most drivers cannot use this mapping.
>
> ==== Legacy ====
> +irq_domain_add_simple()
> irq_domain_add_legacy()
> irq_domain_add_legacy_isa()
>
> @@ -115,3 +116,7 @@ The legacy map should only be used if fixed IRQ mappings must be
> supported. For example, ISA controllers would use the legacy map for
> mapping Linux IRQs 0-15 so that existing ISA drivers get the correct IRQ
> numbers.
> +
> +Most users of legacy mappings should use irq_domain_add_simple() which
> +will use a legacy domain only if an IRQ range is supplied by the
> +system and will otherwise use a linear domain mapping.
> diff --git a/include/linux/irqdomain.h b/include/linux/irqdomain.h
> index 5abb533e..17b60be 100644
> --- a/include/linux/irqdomain.h
> +++ b/include/linux/irqdomain.h
> @@ -112,6 +112,11 @@ struct irq_domain {
> };
>
> #ifdef CONFIG_IRQ_DOMAIN
> +struct irq_domain *irq_domain_add_simple(struct device_node *of_node,
> + unsigned int size,
> + unsigned int first_irq,
> + const struct irq_domain_ops *ops,
> + void *host_data);
> struct irq_domain *irq_domain_add_legacy(struct device_node *of_node,
> unsigned int size,
> unsigned int first_irq,
> diff --git a/kernel/irq/irqdomain.c b/kernel/irq/irqdomain.c
> index d3968e9..0c51958 100644
> --- a/kernel/irq/irqdomain.c
> +++ b/kernel/irq/irqdomain.c
> @@ -140,6 +140,36 @@ static unsigned int irq_domain_legacy_revmap(struct irq_domain *domain,
> }
>
> /**
> + * irq_domain_add_simple() - Allocate and register a simple irq_domain.
> + * @of_node: pointer to interrupt controller's device tree node.
> + * @size: total number of irqs in mapping
> + * @first_irq: first number of irq block assigned to the domain
> + * @ops: map/unmap domain callbacks
> + * @host_data: Controller private data pointer
> + *
> + * Allocates a legacy irq_domain if irq_base is positive or a linear
> + * domain otherwise.
> + *
> + * This is intended to implement the expected behaviour for most
> + * interrupt controllers which is that a linear mapping should
> + * normally be used unless the system requires a legacy mapping in
> + * order to support supplying interrupt numbers during non-DT
> + * registration of devices.
> + */
> +struct irq_domain *irq_domain_add_simple(struct device_node *of_node,
> + unsigned int size,
> + unsigned int first_irq,
> + const struct irq_domain_ops *ops,
> + void *host_data)
> +{
> + if (first_irq > 0)
> + return irq_domain_add_legacy(of_node, size, first_irq, 0,
> + ops, host_data);
> + else
> + return irq_domain_add_linear(of_node, size, ops, host_data);
> +}
> +
> +/**
> * irq_domain_add_legacy() - Allocate and register a legacy revmap irq_domain.
> * @of_node: pointer to interrupt controller's device tree node.
> * @size: total number of irqs in legacy mapping
> --
> 1.7.10
>

--
Grant Likely, B.Sc, P.Eng.
Secret Lab Technologies, Ltd.


\
 
 \ /
  Last update: 2012-07-12 06:21    [W:0.056 / U:0.084 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site