lkml.org 
[lkml]   [2012]   [Jun]   [28]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH v1 09/11] drivers: usb: musb: Add device tree support for omap musb glue
    Date
    Added device tree support for omap musb driver and updated the
    Documentation with device tree binding information.

    Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
    ---
    Documentation/devicetree/bindings/usb/omap-usb.txt | 34 ++++++++++++-
    drivers/usb/musb/omap2430.c | 52 ++++++++++++++++++++
    2 files changed, 85 insertions(+), 1 deletions(-)

    diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
    index 80a28c9..39cdffb 100644
    --- a/Documentation/devicetree/bindings/usb/omap-usb.txt
    +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
    @@ -1,4 +1,4 @@
    -OMAP USB PHY
    +OMAP USB PHY AND GLUE

    OMAP USB2 PHY

    @@ -14,3 +14,35 @@ usb2phy@0x4a0ad080 {
    compatible = "ti,omap-usb2";
    reg = <0x4a0ad080 0x58>;
    };
    +
    +OMAP MUSB GLUE
    + - compatible : Should be "ti,musb-omap2430"
    + - ti,hwmods : must be "usb_otg_hs"
    + - multipoint : Should be "1" indicating the musb controller supports
    + multipoint. This is a MUSB configuration-specific setting.
    + - num_eps : Specifies the number of endpoints. This is also a
    + MUSB configuration-specific setting. Should be set to "16"
    + - ram_bits : Specifies the ram address size. Should be set to "12"
    + - interface_type : This is a board specific setting to describe the type of
    + interface between the controller and the phy. It should be "0" or "1"
    + specifying ULPI and UTMI respectively.
    + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
    + represents PERIPHERAL.
    + - power : Should be "50". This signifies the controller can supply upto
    + 100mA when operating in host mode.
    +
    +SOC specific device node entry
    +usb_otg_hs: usb_otg_hs@4a0ab000 {
    + compatible = "ti,musb-omap2430";
    + ti,hwmods = "usb_otg_hs";
    + multipoint = <1>;
    + num_eps = <16>;
    + ram_bits = <12>;
    +};
    +
    +Board specific device node entry
    +&usb_otg_hs {
    + interface_type = <1>;
    + mode = <3>;
    + power = <50>;
    +};
    diff --git a/drivers/usb/musb/omap2430.c b/drivers/usb/musb/omap2430.c
    index a50bd73..c750f11 100644
    --- a/drivers/usb/musb/omap2430.c
    +++ b/drivers/usb/musb/omap2430.c
    @@ -30,6 +30,7 @@
    #include <linux/init.h>
    #include <linux/list.h>
    #include <linux/io.h>
    +#include <linux/of.h>
    #include <linux/platform_device.h>
    #include <linux/dma-mapping.h>
    #include <linux/pm_runtime.h>
    @@ -469,8 +470,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32);
    static int __devinit omap2430_probe(struct platform_device *pdev)
    {
    struct musb_hdrc_platform_data *pdata = pdev->dev.platform_data;
    + struct omap_musb_board_data *data;
    struct platform_device *musb;
    struct omap2430_glue *glue;
    + struct device_node *np = pdev->dev.of_node;
    + struct musb_hdrc_config *config;
    struct resource *res;
    int ret = -ENOMEM;

    @@ -500,6 +504,43 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
    if (glue->control_otghs == NULL)
    dev_dbg(&pdev->dev, "Failed to obtain control memory\n");

    + if (np) {
    + pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
    + if (!pdata) {
    + dev_err(&pdev->dev,
    + "failed to allocate musb platfrom data\n");
    + ret = -ENOMEM;
    + goto err1;
    + }
    +
    + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
    + if (!data) {
    + dev_err(&pdev->dev,
    + "failed to allocate musb board data\n");
    + ret = -ENOMEM;
    + goto err1;
    + }
    +
    + config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL);
    + if (!data) {
    + dev_err(&pdev->dev,
    + "failed to allocate musb hdrc config\n");
    + goto err1;
    + }
    +
    + of_property_read_u32(np, "mode", (u32 *)&pdata->mode);
    + of_property_read_u32(np, "interface_type",
    + (u32 *)&data->interface_type);
    + of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps);
    + of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits);
    + of_property_read_u32(np, "mode", (u32 *)&pdata->mode);
    + of_property_read_u32(np, "power", (u32 *)&pdata->power);
    + config->multipoint = of_property_read_bool(np, "multipoint");
    +
    + pdata->board_data = data;
    + pdata->config = config;
    + }
    +
    pdata->platform_ops = &omap2430_ops;

    platform_set_drvdata(pdev, glue);
    @@ -597,12 +638,23 @@ static struct dev_pm_ops omap2430_pm_ops = {
    #define DEV_PM_OPS NULL
    #endif

    +#ifdef CONFIG_OF
    +static const struct of_device_id omap2430_id_table[] = {
    + { .compatible = "ti,musb-omap2430" },
    + {}
    +};
    +MODULE_DEVICE_TABLE(of, omap2430_id_table);
    +#else
    +#define omap2430_id_table NULL
    +#endif
    +
    static struct platform_driver omap2430_driver = {
    .probe = omap2430_probe,
    .remove = __devexit_p(omap2430_remove),
    .driver = {
    .name = "musb-omap2430",
    .pm = DEV_PM_OPS,
    + .of_match_table = omap2430_id_table,
    },
    };

    --
    1.7.5.4


    \
     
     \ /
      Last update: 2012-06-28 14:21    [W:3.235 / U:0.052 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site