lkml.org 
[lkml]   [2012]   [Mar]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 09/10 v2] drm/i915/intel_i2c: reuse GMBUS2 value read in polling loop
Date
Save the GMBUS2 value read while polling for state changes, and then
reuse this value when determining for which reason the loops were exited.
This is a small optimization which saves a couple of bus accesses for
memory mapped IO registers.

Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
---
drivers/gpu/drm/i915/intel_i2c.c | 19 ++++++++++---------
1 files changed, 10 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_i2c.c b/drivers/gpu/drm/i915/intel_i2c.c
index 61fe317..2c372d3 100644
--- a/drivers/gpu/drm/i915/intel_i2c.c
+++ b/drivers/gpu/drm/i915/intel_i2c.c
@@ -243,6 +243,7 @@ gmbus_xfer(struct i2c_adapter *adapter,
struct drm_i915_private *dev_priv = adapter->algo_data;
int i, reg_offset;
int ret = 0;
+ u32 gmbus2 = 0;

if (bus->force_bit)
return intel_i2c_quirk_xfer(dev_priv,
@@ -296,12 +297,12 @@ gmbus_xfer(struct i2c_adapter *adapter,
do {
u32 val, loop = 0;

- if (wait_for(I915_READ(GMBUS2 + reg_offset) &
+ if (wait_for((gmbus2 = I915_READ(GMBUS2 +
+ reg_offset)) &
(GMBUS_SATOER | GMBUS_HW_RDY),
50))
goto timeout;
- if (I915_READ(GMBUS2 + reg_offset) &
- GMBUS_SATOER)
+ if (gmbus2 & GMBUS_SATOER)
goto clear_err;

val = I915_READ(GMBUS3 + reg_offset);
@@ -335,21 +336,21 @@ gmbus_xfer(struct i2c_adapter *adapter,
I915_WRITE(GMBUS3 + reg_offset, val);
POSTING_READ(GMBUS2 + reg_offset);

- if (wait_for(I915_READ(GMBUS2 + reg_offset) &
+ if (wait_for((gmbus2 = I915_READ(GMBUS2 +
+ reg_offset)) &
(GMBUS_SATOER | GMBUS_HW_RDY),
50))
goto timeout;
- if (I915_READ(GMBUS2 + reg_offset) &
- GMBUS_SATOER)
+ if (gmbus2 & GMBUS_SATOER)
goto clear_err;
}
}

- if (wait_for(I915_READ(GMBUS2 + reg_offset) &
+ if (wait_for((gmbus2 = I915_READ(GMBUS2 + reg_offset)) &
(GMBUS_SATOER | GMBUS_HW_WAIT_PHASE),
50))
goto timeout;
- if (I915_READ(GMBUS2 + reg_offset) & GMBUS_SATOER)
+ if (gmbus2 & GMBUS_SATOER)
goto clear_err;
}

@@ -373,7 +374,7 @@ clear_err:
ret = -ENXIO;

done:
- if (I915_READ(GMBUS2 + reg_offset) & GMBUS_HW_WAIT_PHASE) {
+ if (gmbus2 & GMBUS_HW_WAIT_PHASE) {
I915_WRITE(GMBUS1 + reg_offset,
GMBUS_CYCLE_STOP | GMBUS_SW_RDY);
POSTING_READ(GMBUS2 + reg_offset);
--
1.7.7.3


\
 
 \ /
  Last update: 2012-03-09 19:57    [W:0.064 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site