lkml.org 
[lkml]   [2012]   [Mar]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRE: I.MX35 PDK

> Yes this I2C problem, all I2C slave device need response to Host CPU by
> pulls I2C data bus to low, in other words generate ACK, the clock pulse for
> the acknowledge bit is always created by the bus master.
>
> In this case, the camera tries to reset the data bus and generate an ACK,
> but the voltage drops to the area of two volts, although it should be reset
> to zero.
> I replaced R172 with 10K on CPU board and got a good result, but there are
> other surprises

>Ok, good.

>Can you try to change the I2C1 pad settings in software, so that the
>board can work with the original resistor?

In the near future I will check this option:-)

>
> Linux video capture interface: v2.00
> soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0
> mx3-camera mx3-camera.0: MX3 Camera driver attached to camera 0
> ov2640 0-0030: ov2640 Product ID 26:42 Manufacturer ID 7f:a2
> i2c i2c-0: OV2640 Probed1
> mx3-camera mx3-camera.0: MX3 Camera driver detached from camera 0
> dmaengine: failed to get dma1chan0: (-22)
> dmaengine: failed to get dma1chan1: (-22)
> dmaengine: failed to get dma1chan2: (-22)
> dmaengine: failed to get dma1chan3: (-22)
> dmaengine: failed to get dma1chan4: (-22)
> dmaengine: failed to get dma1chan5: (-22)
> dmaengine: failed to get dma1chan6: (-22)
> dmaengine: failed to get dma1chan7: (-22)
> dmaengine: failed to get dma1chan8: (-22)
> dmaengine: failed to get dma1chan9: (-22)
> dmaengine: failed to get dma1chan10: (-22)
> dmaengine: failed to get dma1chan11: (-22)
> dmaengine: failed to get dma1chan12: (-22)
> dmaengine: failed to get dma1chan13: (-22)
> dmaengine: failed to get dma1chan14: (-22)
> dmaengine: failed to get dma1chan15: (-22)
> dmaengine: failed to get dma1chan16: (-22)
> dmaengine: failed to get dma1chan17: (-22)
> dmaengine: failed to get dma1chan18: (-22)
> dmaengine: failed to get dma1chan19: (-22)
> dmaengine: failed to get dma1chan20: (-22)
> dmaengine: failed to get dma1chan21: (-22)
> dmaengine: failed to get dma1chan22: (-22)
> dmaengine: failed to get dma1chan23: (-22)
> dmaengine: failed to get dma1chan24: (-22)
> dmaengine: failed to get dma1chan25: (-22)
> dmaengine: failed to get dma1chan26: (-22)
> dmaengine: failed to get dma1chan27: (-22)
> dmaengine: failed to get dma1chan28: (-22)
> dmaengine: failed to get dma1chan29: (-22)
> dmaengine: failed to get dma1chan30: (-22):

>This is something that needs to be solved, but it does not prevent the
>camera to work though.

>On my mx31pdk I get the same dmaengine errors and the ov2640 does work fine.
>I think you can go ahead and try to use the camera on the mx35pdk now.
>You can try:

>gst-launch -v v4l2src device=/dev/video0 !
>video/x-raw-yuv,width=320,height=240,framerate=25/1 ! ffmpegcolorspace
>! fbdevsink

Thank Fabio I'll try to check it.

Regards
Alex Gershgorin


\
 
 \ /
  Last update: 2012-03-08 13:13    [W:0.056 / U:0.468 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site