lkml.org 
[lkml]   [2011]   [Aug]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] usb: gadget: storage_common: make FSG_NUM_BUFFERS variable size
On Mon, 8 Aug 2011, Per Forlin wrote:

> FSG_NUM_BUFFERS is set to 2 as default.
> Usually 2 buffers are enough to establish a good
> double buffering pipeline. But when dealing with expensive
> request preparation (i.e. dma_map) there may be benefits of
> increasing the number of buffers. There is an extra cost for
> every first request, the others are prepared in parallell with
> an ongoing transfer. Every time all buffers are consumed there is
> an additional cost for the next first request. Increasing the number
> of buffers decreases the risk of running out of buffers.

The reasoning here is not clear. Throughput is limited on the device
side mostly by the time required to prepare the buffer, transfer the
data, and copy the data to/from the backing storage. Using more
buffers won't affect this directly. Putting this another way, if the
time required to prepare a buffer and copy the data is longer than the
time needed to transfer the data over the USB link, the throughput
won't be optimal no matter how many buffers you use.

On the other hand, adding buffers will smooth out irregularities and
latencies caused by scheduling delays when other tasks are running at
the same time. Still, I would expect the benefit to be fairly small
and to diminish rapidly as more buffers are added.

> Test set up
> * Running dd on the host reading from the mass storage device
> * cmdline: dd if=/dev/sdb of=/dev/null bs=4k count=$((256*100))
> * Caches are dropped on the host and on the device before each run
>
> Measurements on a Snowball board with ondemand_govenor active.
>
> FSG_NUM_BUFFERS 2
> 104857600 bytes (105 MB) copied, 5.62173 s, 18.7 MB/s
> 104857600 bytes (105 MB) copied, 5.61811 s, 18.7 MB/s
> 104857600 bytes (105 MB) copied, 5.57817 s, 18.8 MB/s
> 104857600 bytes (105 MB) copied, 5.57769 s, 18.8 MB/s
> 104857600 bytes (105 MB) copied, 5.59654 s, 18.7 MB/s
> 104857600 bytes (105 MB) copied, 5.58948 s, 18.8 MB/s
>
> FSG_NUM_BUFFERS 4
> 104857600 bytes (105 MB) copied, 5.26839 s, 19.9 MB/s
> 104857600 bytes (105 MB) copied, 5.2691 s, 19.9 MB/s
> 104857600 bytes (105 MB) copied, 5.2711 s, 19.9 MB/s
> 104857600 bytes (105 MB) copied, 5.27174 s, 19.9 MB/s
> 104857600 bytes (105 MB) copied, 5.27261 s, 19.9 MB/s
> 104857600 bytes (105 MB) copied, 5.27135 s, 19.9 MB/s
> 104857600 bytes (105 MB) copied, 5.27249 s, 19.9 MB/s

Okay, 6% is a worthwhile improvement, though not huge. Did you try 6
or 8 buffers? I bet going beyond 4 makes very little difference.

> There may not be one optimal number for all boards. That is the
> reason for adding the number to Kconfig,
>
> Signed-off-by: Per Forlin <per.forlin@linaro.org>
> ---
> drivers/usb/gadget/Kconfig | 15 +++++++++++++++
> drivers/usb/gadget/storage_common.c | 4 ++--
> 2 files changed, 17 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig
> index 029e288..bbd17f3 100644
> --- a/drivers/usb/gadget/Kconfig
> +++ b/drivers/usb/gadget/Kconfig
> @@ -96,6 +96,21 @@ config USB_GADGET_VBUS_DRAW
> This value will be used except for system-specific gadget
> drivers that have more specific information.
>
> +config USB_GADGET_STORAGE_NUM_BUFFERS
> + int "Number of storage pipline buffers"
> + range 2 64

64 is definitely way into the overkill range. I'd be very tempted to
leave the maximum set at 4. You might even consider setting it to 4
always -- although each buffer requires 16 KB of contiguous kernel
memory so minimizing the number of buffers is always desirable.

Alan Stern



\
 
 \ /
  Last update: 2011-08-08 16:37    [W:1.802 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site