lkml.org 
[lkml]   [2011]   [May]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Subject[PATCH 12/16] hpsa: use new doorbell-bit-5 reset method
From
Date
From: Stephen M. Cameron <scameron@beardog.cce.hp.com>

The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register. We want to
use it if it's available.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
---
drivers/scsi/hpsa.c | 25 ++++++++++++++++++++-----
drivers/scsi/hpsa_cmd.h | 2 ++
2 files changed, 22 insertions(+), 5 deletions(-)

diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c
index ca92141..c096cda 100644
--- a/drivers/scsi/hpsa.c
+++ b/drivers/scsi/hpsa.c
@@ -3128,7 +3128,7 @@ static __devinit int hpsa_message(struct pci_dev *pdev, unsigned char opcode,
#define hpsa_noop(p) hpsa_message(p, 3, 0)

static int hpsa_controller_hard_reset(struct pci_dev *pdev,
- void * __iomem vaddr, bool use_doorbell)
+ void * __iomem vaddr, u32 use_doorbell)
{
u16 pmcsr;
int pos;
@@ -3139,7 +3139,7 @@ static int hpsa_controller_hard_reset(struct pci_dev *pdev,
* other way using the doorbell register.
*/
dev_info(&pdev->dev, "using doorbell to reset controller\n");
- writel(DOORBELL_CTLR_RESET, vaddr + SA5_DOORBELL);
+ writel(use_doorbell, vaddr + SA5_DOORBELL);
msleep(1000);
} else { /* Try to do it the PCI power state way */

@@ -3243,7 +3243,7 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
u32 misc_fw_support;
int rc;
struct CfgTable __iomem *cfgtable;
- bool use_doorbell;
+ u32 use_doorbell;
u32 board_id;
u16 command_register;

@@ -3306,9 +3306,24 @@ static __devinit int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev)
if (rc)
goto unmap_vaddr;

- /* If reset via doorbell register is supported, use that. */
+ /* If reset via doorbell register is supported, use that.
+ * There are two such methods. Favor the newest method.
+ */
misc_fw_support = readl(&cfgtable->misc_fw_support);
- use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET;
+ use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET2;
+ if (use_doorbell) {
+ use_doorbell = DOORBELL_CTLR_RESET2;
+ } else {
+ use_doorbell = misc_fw_support & MISC_FW_DOORBELL_RESET;
+ if (use_doorbell) {
+ dev_warn(&pdev->dev, "Controller claims that "
+ "'Bit 2 doorbell reset' is "
+ "supported, but not 'bit 5 doorbell reset'. "
+ "Firmware update is recommended.\n");
+ rc = -ENODEV;
+ goto unmap_cfgtable;
+ }
+ }

rc = hpsa_controller_hard_reset(pdev, vaddr, use_doorbell);
if (rc)
diff --git a/drivers/scsi/hpsa_cmd.h b/drivers/scsi/hpsa_cmd.h
index 8fd35a7..55d741b 100644
--- a/drivers/scsi/hpsa_cmd.h
+++ b/drivers/scsi/hpsa_cmd.h
@@ -101,6 +101,7 @@
#define CFGTBL_ChangeReq 0x00000001l
#define CFGTBL_AccCmds 0x00000001l
#define DOORBELL_CTLR_RESET 0x00000004l
+#define DOORBELL_CTLR_RESET2 0x00000020l

#define CFGTBL_Trans_Simple 0x00000002l
#define CFGTBL_Trans_Performant 0x00000004l
@@ -337,6 +338,7 @@ struct CfgTable {
u8 reserved[0x78 - 0x58];
u32 misc_fw_support; /* offset 0x78 */
#define MISC_FW_DOORBELL_RESET (0x02)
+#define MISC_FW_DOORBELL_RESET2 (0x010)
u8 driver_version[32];
};



\
 
 \ /
  Last update: 2011-05-03 22:03    [W:0.137 / U:0.260 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site