lkml.org 
[lkml]   [2011]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 06/10] ARM: OMAP1: ams-delta: Use GPIO API in modem setup
Date
Don't use Amstrad Delta custom I/O functions for setting up modem
related pins, use GPIO API instead. However, keep old pin definitions
used by ams_delta_latch2_write() for now, as those are still used by the
Amstrad Delta ASoC driver.

While being at it, extend the device platform data with a power
management hook which toggles one of those new GPIO pins.

Depends on patch 2/10 "ARM: OMAP1: Convert Amstrad E3 latches to
basic_mmio_gpio".

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
---
arch/arm/mach-omap1/board-ams-delta.c | 44 ++++++++++++++++++++------------
1 files changed, 27 insertions(+), 17 deletions(-)

diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 7670374..5705481 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -262,16 +262,6 @@ static struct gpio _latch_gpios[] __initconst = {
.label = "scard_cmdvcc",
},
{
- .gpio = AMS_DELTA_GPIO_PIN_MODEM_NRESET,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "modem_nreset",
- },
- {
- .gpio = AMS_DELTA_GPIO_PIN_MODEM_CODEC,
- .flags = GPIOF_OUT_INIT_LOW,
- .label = "modem_codec",
- },
- {
.gpio = AMS_DELTA_LATCH2_GPIO_BASE + 14,
.flags = GPIOF_OUT_INIT_LOW,
.label = "hookflash1",
@@ -482,6 +472,12 @@ static void __init ams_delta_init(void)
omap_writew(omap_readw(ARM_RSTCT1) | 0x0004, ARM_RSTCT1);
}

+static void _modem_pm(struct uart_port *port, unsigned int state, unsigned old)
+{
+ if (state != old)
+ gpio_set_value(AMS_DELTA_GPIO_PIN_MODEM_NRESET, state == 0);
+}
+
static struct plat_serial8250_port ams_delta_modem_ports[] = {
{
.membase = IOMEM(_MODEM_VIRT),
@@ -492,6 +488,7 @@ static struct plat_serial8250_port ams_delta_modem_ports[] = {
.iotype = UPIO_MEM,
.regshift = 1,
.uartclk = BASE_BAUD * 16,
+ .pm = _modem_pm,
},
{ },
};
@@ -504,6 +501,24 @@ static struct platform_device ams_delta_modem_device = {
},
};

+static struct gpio _modem_gpios[] __initconst = {
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_MODEM_IRQ,
+ .flags = GPIOF_DIR_IN,
+ .label = "modem_irq",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_MODEM_NRESET,
+ .flags = GPIOF_OUT_INIT_HIGH,
+ .label = "modem_nreset",
+ },
+ {
+ .gpio = AMS_DELTA_GPIO_PIN_MODEM_CODEC,
+ .flags = GPIOF_OUT_INIT_HIGH,
+ .label = "modem_codec",
+ },
+};
+
static int __init ams_delta_modem_init(void)
{
int err;
@@ -515,16 +530,11 @@ static int __init ams_delta_modem_init(void)
ams_delta_modem_ports[0].irq =
gpio_to_irq(AMS_DELTA_GPIO_PIN_MODEM_IRQ);

- err = gpio_request(AMS_DELTA_GPIO_PIN_MODEM_IRQ, "modem");
+ err = gpio_request_array(_modem_gpios, ARRAY_SIZE(_modem_gpios));
if (err) {
- pr_err("Couldn't request gpio pin for modem\n");
+ pr_err("Couldn't request gpio pins for modem\n");
return err;
}
- gpio_direction_input(AMS_DELTA_GPIO_PIN_MODEM_IRQ);
-
- ams_delta_latch2_write(
- AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC,
- AMS_DELTA_LATCH2_MODEM_NRESET | AMS_DELTA_LATCH2_MODEM_CODEC);

return platform_device_register(&ams_delta_modem_device);
}
--
1.7.3.4


\
 
 \ /
  Last update: 2011-12-11 21:19    [W:0.572 / U:0.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site