lkml.org 
[lkml]   [2011]   [Nov]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v3] input: add driver support for Sharp gp2ap002a00f proximity sensor
Hi Dmitry,

On 13:18 Wed 16 Nov , Oskar Andero wrote:
> On 12:28 Wed 16 Nov , Shubhrajyoti wrote:
> > On Wednesday 16 November 2011 04:07 PM, oskar.andero@sonyericsson.com
> > wrote:
> > > On 19:29 Tue 15 Nov , Dmitry Torokhov wrote:
> > >> On Tue, Nov 15, 2011 at 01:53:52PM +0100, oskar.andero@sonyericsson.com wrote:
> > >>> On 10:43 Tue 15 Nov , Dmitry Torokhov wrote:
> > >>>> On Tue, Nov 15, 2011 at 10:26:00AM +0100, oskar.andero@sonyericsson.com wrote:
> > >>>>> From: Courtney Cavin <courtney.cavin@sonyericsson.com>
> > >>>>> +
> > >>>>> +#ifdef CONFIG_PM_SLEEP
> > >>>>> +static int gp2a_suspend(struct device *dev)
> > >>>>> +{
> > >>>>> + struct i2c_client *client = to_i2c_client(dev);
> > >>>>> + struct gp2a_data *dt = i2c_get_clientdata(client);
> > >>>>> + int error;
> > >>>>> +
> > >>>>> + mutex_lock(&dt->device->mutex);
> > >>>>> +
> > >>>>> + if (dt->device->users) {
> > >>>>> + if (device_may_wakeup(&client->dev)) {
> > >>>>> + enable_irq_wake(client->irq);
> > >>>> I think this part should happen regardless of whether device has users,
> > >>>> only non wakeup source case needs it.
> > >>> Hmm.. why would one want to enable irq_wake when there are no users?
> > >>> Wouldn't this cause the device to wakeup at every irq and report an
> > >>> switch event that no one listens to?
> > >> You are suspending the system and want to have this device as a wakeup
> > >> source. Note: not wake up _device_ at every IRQ but wake up the whole
> > >> _system_ when device generates an IRQ while system is asleep.
> > >> It does not matter whether there are users for the events; you
> > >> want the system to wake up.
> > >>
> > >> At least this is the usual semantics.
> > > I see you point. However, the way we use the proximity sensor we can only wake up
> > > the system when we have an application that is actually interested in the change.
> > > This is for power save reasons.
> > > If we use the "usual semantic", we would wake up the system at every proximity
> > > detection regardlessly. For instance, I wouldn't want to wake up a cell phone laying
> > > on the desk when I put my hand over it. That would hurt the battery time.
> > Even in that case it shouldn't harm the power if no user is there the
> > close would have been called
> > and you should be in the shut down mode? Am I missing something?
>
> You are right - the chip will only generate interrupts when it's opened, so the case
> I described shouldn't actually be a problem. However, does it make sense to enable irq_wake
> for a device that will never generate interrupts?

Do you have any input on my question above? My suggestion is to keep the code as it is,
unless you see a reason for enabling wake_irq on an irq that will never happen.

I'll prepare v4 as soon as I have your answer.

Thanks!

-Oskar


\
 
 \ /
  Last update: 2011-11-17 12:23    [W:2.064 / U:1.112 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site