lkml.org 
[lkml]   [2011]   [Nov]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 3/5] net-next:asix: reduce AX88772 init time by about 2 seconds
Date
ax88772_reset takes about 2 seconds and is called twice.
Once from ax88772_bind() directly and again indirectly from usbnet_open().
Reset the USB FW/Phy enough to blink the LEDs when inserted.

Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
---
drivers/net/usb/asix.c | 30 +++++++++++++++++++++++++-----
1 files changed, 25 insertions(+), 5 deletions(-)

diff --git a/drivers/net/usb/asix.c b/drivers/net/usb/asix.c
index b4675e8..8462be5 100644
--- a/drivers/net/usb/asix.c
+++ b/drivers/net/usb/asix.c
@@ -1083,7 +1083,7 @@ static const struct net_device_ops ax88772_netdev_ops = {

static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
{
- int ret;
+ int ret, embd_phy;
struct asix_data *data = (struct asix_data *)&dev->data;
u8 buf[ETH_ALEN];
u32 phyid;
@@ -1108,16 +1108,36 @@ static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf)
dev->mii.reg_num_mask = 0x1f;
dev->mii.phy_id = asix_get_phy_addr(dev);

- phyid = asix_get_phyid(dev);
- dbg("PHYID=0x%08x", phyid);
-
dev->net->netdev_ops = &ax88772_netdev_ops;
dev->net->ethtool_ops = &ax88772_ethtool_ops;

- ret = ax88772_reset(dev);
+ embd_phy = ((dev->mii.phy_id & 0x1f) == 0x10 ? 1 : 0);
+
+ /* Reset the PHY to normal operation mode */
+ ret = asix_write_cmd(dev, AX_CMD_SW_PHY_SELECT, embd_phy, 0, 0, NULL);
+ if (ret < 0) {
+ dbg("Select PHY #1 failed: %d", ret);
+ return ret;
+ }
+
+ ret = asix_sw_reset(dev, AX_SWRESET_IPPD | AX_SWRESET_PRL);
if (ret < 0)
return ret;

+ msleep(150);
+
+ ret = asix_sw_reset(dev, AX_SWRESET_CLEAR);
+ if (ret < 0)
+ return ret;
+
+ msleep(150);
+
+ ret = asix_sw_reset(dev, embd_phy ? AX_SWRESET_IPRL : AX_SWRESET_PRTE);
+
+ /* Read PHYID register *AFTER* the PHY was reset properly */
+ phyid = asix_get_phyid(dev);
+ dbg("PHYID=0x%08x", phyid);
+
/* Asix framing packs multiple eth frames into a 2K usb bulk transfer */
if (dev->driver_info->flags & FLAG_FRAMING_AX) {
/* hard_mtu is still the default - the device does not support
--
1.7.3.1


\
 
 \ /
  Last update: 2011-11-15 00:25    [W:2.154 / U:0.012 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site