lkml.org 
[lkml]   [2011]   [Oct]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 5/5] tty/serial: atmel_serial: add device tree support
Date
Will use aliases to enumerate ports, if available.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
---
drivers/tty/serial/atmel_serial.c | 79 +++++++++++++++++++++++++++++++++----
1 files changed, 71 insertions(+), 8 deletions(-)

diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 1074329..fc4081e 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -33,6 +33,8 @@
#include <linux/sysrq.h>
#include <linux/tty_flip.h>
#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/dma-mapping.h>
#include <linux/atmel_pdc.h>
#include <linux/atmel_serial.h>
@@ -163,6 +165,16 @@ static unsigned long atmel_ports_in_use;
static struct console atmel_console;
#endif

+#if defined(CONFIG_OF)
+static const struct of_device_id atmel_serial_dt_ids[] = {
+ { .compatible = "atmel,at91rm9200-usart" },
+ { .compatible = "atmel,at91sam9260-usart" },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(of, atmel_serial_dt_ids);
+#endif
+
static inline struct atmel_uart_port *
to_atmel_uart_port(struct uart_port *uart)
{
@@ -1411,6 +1423,48 @@ static struct uart_ops atmel_pops = {
#endif
};

+static void __devinit atmel_of_init_port(struct atmel_uart_port *atmel_port,
+ struct device_node *np)
+{
+ u32 rs485_delay[2];
+
+ /* DMA/PDC usage specification */
+ if (of_get_property(np, "atmel,use-dma-rx", NULL))
+ atmel_port->use_dma_rx = 1;
+ else
+ atmel_port->use_dma_rx = 0;
+ if (of_get_property(np, "atmel,use-dma-tx", NULL))
+ atmel_port->use_dma_tx = 1;
+ else
+ atmel_port->use_dma_tx = 0;
+
+ /* rs485 properties */
+ if (of_property_read_u32_array(np, "rs485-rts-delay",
+ rs485_delay, 2) == 0) {
+ struct serial_rs485 *rs485conf = &atmel_port->rs485;
+
+ rs485conf->delay_rts_before_send = rs485_delay[0];
+ rs485conf->delay_rts_after_send = rs485_delay[1];
+ rs485conf->flags = 0;
+
+ if (rs485conf->delay_rts_before_send == 0 &&
+ rs485conf->delay_rts_after_send == 0) {
+ rs485conf->flags |= SER_RS485_RTS_ON_SEND;
+ } else {
+ if (rs485conf->delay_rts_before_send)
+ rs485conf->flags |= SER_RS485_RTS_BEFORE_SEND;
+ if (rs485conf->delay_rts_after_send)
+ rs485conf->flags |= SER_RS485_RTS_AFTER_SEND;
+ }
+
+ if (of_get_property(np, "rs485-rx-during-tx", NULL))
+ rs485conf->flags |= SER_RS485_RX_DURING_TX;
+
+ if (of_get_property(np, "linux,rs485-enabled-at-boot-time", NULL))
+ rs485conf->flags |= SER_RS485_ENABLED;
+ }
+}
+
/*
* Configure the port from the platform device resource info.
*/
@@ -1420,6 +1474,14 @@ static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
struct uart_port *port = &atmel_port->uart;
struct atmel_uart_data *pdata = pdev->dev.platform_data;

+ if (pdev->dev.of_node) {
+ atmel_of_init_port(atmel_port, pdev->dev.of_node);
+ } else {
+ atmel_port->use_dma_rx = pdata->use_dma_rx;
+ atmel_port->use_dma_tx = pdata->use_dma_tx;
+ atmel_port->rs485 = pdata->rs485;
+ }
+
port->iotype = UPIO_MEM;
port->flags = UPF_BOOT_AUTOCONF;
port->ops = &atmel_pops;
@@ -1433,7 +1495,7 @@ static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,

memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));

- if (pdata->regs) {
+ if (pdata && pdata->regs) {
/* Already mapped by setup code */
port->membase = pdata->regs;
} else {
@@ -1450,10 +1512,6 @@ static void __devinit atmel_init_port(struct atmel_uart_port *atmel_port,
/* only enable clock when USART is in use */
}

- atmel_port->use_dma_rx = pdata->use_dma_rx;
- atmel_port->use_dma_tx = pdata->use_dma_tx;
- atmel_port->rs485 = pdata->rs485;
-
/* Use TXEMPTY for interrupt when rs485 else TXRDY or ENDTX|TXBUFE */
if (atmel_port->rs485.flags & SER_RS485_ENABLED)
atmel_port->tx_done_mask = ATMEL_US_TXEMPTY;
@@ -1718,17 +1776,21 @@ static int atmel_serial_resume(struct platform_device *pdev)
static int __devinit atmel_serial_probe(struct platform_device *pdev)
{
struct atmel_uart_port *port;
+ struct device_node *np = pdev->dev.of_node;
struct atmel_uart_data *pdata = pdev->dev.platform_data;
void *data;
int ret = -ENODEV;

BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));

- if (pdata)
- ret = pdata->num;
+ if (np)
+ ret = of_alias_get_id(np, "serial");
+ else
+ if (pdata)
+ ret = pdata->num;

if (ret < 0)
- /* port id not found in platform data:
+ /* port id not found in platform data nor device-tree aliases:
* auto-enumerate it */
ret = find_first_zero_bit(&atmel_ports_in_use,
sizeof(atmel_ports_in_use));
@@ -1827,6 +1889,7 @@ static struct platform_driver atmel_serial_driver = {
.driver = {
.name = "atmel_usart",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(atmel_serial_dt_ids),
},
};

--
1.7.5.4


\
 
 \ /
  Last update: 2011-10-12 18:11    [W:0.062 / U:0.668 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site