lkml.org 
[lkml]   [2010]   [Jun]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCHv2 04/11] OMAP2: Devkit8000: Setup LCD reset
Date
From: Kan-Ru Chen <kanru@0xlab.org>

This patch corrects the LCD reset pin configuration.

Original code from early devkit8000 patch sets the TWL4030 GPIO_1
to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins
are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be
disabled when other display is turned on.

Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
---
arch/arm/mach-omap2/board-devkit8000.c | 11 +++++++++++
1 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 17a2517..70552d8 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c
@@ -134,11 +134,15 @@ static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);

+ if (dssdev->reset_gpio != -EINVAL)
+ gpio_set_value(dssdev->reset_gpio, 1);
return 0;
}

static void devkit8000_panel_disable_lcd(struct omap_dss_device *dssdev)
{
+ if (dssdev->reset_gpio != -EINVAL)
+ gpio_set_value(dssdev->reset_gpio, 0);
}

static int devkit8000_panel_enable_dvi(struct omap_dss_device *dssdev)
@@ -183,6 +187,7 @@ static struct omap_dss_device devkit8000_lcd_device = {
.driver_name = "generic_panel",
.type = OMAP_DISPLAY_TYPE_DPI,
.phy.dpi.data_lines = 24,
+ .reset_gpio = -EINVAL, /* will be replaced */
.platform_enable = devkit8000_panel_enable_lcd,
.platform_disable = devkit8000_panel_disable_lcd,
};
@@ -281,6 +286,12 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;

+ /* gpio + 1 is "LCD_PWREN" (out, active high) */
+ devkit8000_lcd_device.reset_gpio = gpio + 1;
+ gpio_request(devkit8000_lcd_device.reset_gpio, "LCD_PWREN");
+ /* Disable until needed */
+ gpio_direction_output(devkit8000_lcd_device.reset_gpio, 0);
+
/* gpio + 7 is "DVI_PD" (out, active low) */
devkit8000_dvi_device.reset_gpio = gpio + 7;
gpio_request(devkit8000_dvi_device.reset_gpio, "DVI PowerDown");
--
1.7.1


\
 
 \ /
  Last update: 2010-06-02 13:41    [W:0.104 / U:3.296 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site