lkml.org 
[lkml]   [2010]   [Jun]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: hibernation hangs with ATA errors (lockup_detector bug)
    On Tue, Jun 01, 2010 at 04:46:28PM +0200, Jiri Slaby wrote:
    > On 06/01/2010 03:50 PM, Don Zickus wrote:
    > > On Mon, May 31, 2010 at 04:22:00PM +0200, Jiri Slaby wrote:
    > >> Hi,
    > >>
    > >> with -next I get the following errors while trying to hibernate in
    > >> qemu-kvm after the image is stored on disk:
    > >
    > > Is this the host that is hibernating or the guest?
    >
    > Guest.
    >
    > > KVM guests don't emulate the performance counters, so the nmi piece
    > > shouldn't be functioning and the soft lockup piece just sits on top of an
    > > hrtimer, so off the top of my head it is hard to imagine it intefering
    > > with a sata driver.
    > >
    > > I'll need your whole boot up log to see how the lockup detector
    > > initialized itself.
    >
    > Here it goes (till the moment it dies on the ata errors):

    I think I was able to reproduce over here. I guess I didn't test the
    suspend/resume path very well and the cpu transitions states aren't what I
    expected. It looks as though I might have screwed up the hrtimer stuff
    and caused the box to hang when cpu1 when boots up in single cpu mode.

    I'll see if I can get something out to test with later today.

    Cheers,
    Don

    >
    > Linux version 2.6.34-mm1_64+ (ku@bellona) (gcc version 4.5.0 20100420
    > [gcc-4_5-branch revision 158562] (SUSE Linux) ) #1209 SMP Thu May 27
    > 22:57:37 CEST 2010
    > Command line: root=/dev/sda1 resume=/dev/sdb debug no_console_suspend
    > console=ttyS0,115200 console=tty0 printk.time=1 2
    > BIOS-provided physical RAM map:
    > BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
    > BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
    > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
    > BIOS-e820: 0000000000100000 - 000000003e7fb000 (usable)
    > BIOS-e820: 000000003e7fb000 - 000000003e800000 (reserved)
    > BIOS-e820: 00000000fffbc000 - 0000000100000000 (reserved)
    > NX (Execute Disable) protection: active
    > DMI 2.4 present.
    > e820 update range: 0000000000000000 - 0000000000001000 (usable) ==>
    > (reserved)
    > e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    > No AGP bridge found
    > last_pfn = 0x3e7fb max_arch_pfn = 0x400000000
    > MTRR default type: write-back
    > MTRR fixed ranges enabled:
    > 00000-9FFFF write-back
    > A0000-BFFFF uncachable
    > C0000-FFFFF write-protect
    > MTRR variable ranges enabled:
    > 0 base 00E0000000 mask FFE0000000 uncachable
    > 1 disabled
    > 2 disabled
    > 3 disabled
    > 4 disabled
    > 5 disabled
    > 6 disabled
    > 7 disabled
    > PAT not supported by CPU.
    > initial memory mapped : 0 - 20000000
    > init_memory_mapping: 0000000000000000-000000003e7fb000
    > 0000000000 - 003e600000 page 2M
    > 003e600000 - 003e7fb000 page 4k
    > kernel direct mapping tables up to 3e7fb000 @ 8000-b000
    > RAMDISK: 3df2f000 - 3e7f0000
    > ACPI: RSDP 00000000000f84c0 00014 (v00 BOCHS )
    > ACPI: RSDT 000000003e7fde10 00034 (v01 BOCHS BXPCRSDT 00000001 BXPC
    > 00000001)
    > ACPI: FACP 000000003e7ffe40 00074 (v01 BOCHS BXPCFACP 00000001 BXPC
    > 00000001)
    > ACPI: DSDT 000000003e7fdfd0 01E22 (v01 BXPC BXDSDT 00000001 INTL
    > 20090123)
    > ACPI: FACS 000000003e7ffe00 00040
    > ACPI: SSDT 000000003e7fdf80 00044 (v01 BOCHS BXPCSSDT 00000001 BXPC
    > 00000001)
    > ACPI: APIC 000000003e7fde90 0007A (v01 BOCHS BXPCAPIC 00000001 BXPC
    > 00000001)
    > ACPI: HPET 000000003e7fde50 00038 (v01 BOCHS BXPCHPET 00000001 BXPC
    > 00000001)
    > ACPI: Local APIC address 0xfee00000
    > (8/32 early reservations) ==> bootmem [0000000000 - 003e7fb000]
    > #0 [0001000000 - 0001989354] TEXT DATA BSS ==> [0001000000 -
    > 0001989354]
    > #1 [003df2f000 - 003e7f0000] RAMDISK ==> [003df2f000 -
    > 003e7f0000]
    > #2 [000009f000 - 0000100000] BIOS reserved ==> [000009f000 -
    > 0000100000]
    > #3 [000198a000 - 000198a049] BRK ==> [000198a000 -
    > 000198a049]
    > #4 [0000001000 - 0000003000] TRAMPOLINE ==> [0000001000 -
    > 0000003000]
    > #5 [0000003000 - 0000007000] ACPI WAKEUP ==> [0000003000 -
    > 0000007000]
    > #6 [0000008000 - 0000009000] PGTABLE ==> [0000008000 -
    > 0000009000]
    > #7 [0000009000 - 0000011000] BOOTMAP ==> [0000009000 -
    > 0000011000]
    > [ffffea0000000000-ffffea0000dfffff] PMD ->
    > [ffff880002200000-ffff880002ffffff] on node 0
    > sizeof(struct page) = 56
    > Zone PFN ranges:
    > DMA 0x00000001 -> 0x00001000
    > DMA32 0x00001000 -> 0x00100000
    > Normal empty
    > Movable zone start PFN for each node
    > early_node_map[2] active PFN ranges
    > 0: 0x00000001 -> 0x0000009f
    > 0: 0x00000100 -> 0x0003e7fb
    > On node 0 totalpages: 255897
    > DMA zone: 56 pages used for memmap
    > DMA zone: 112 pages reserved
    > DMA zone: 3830 pages, LIFO batch:0
    > DMA32 zone: 3444 pages used for memmap
    > DMA32 zone: 248455 pages, LIFO batch:31
    > ACPI: PM-Timer IO Port: 0xb008
    > ACPI: Local APIC address 0xfee00000
    > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    > ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    > IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
    > ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
    > ACPI: IRQ0 used by override.
    > ACPI: IRQ2 used by override.
    > ACPI: IRQ5 used by override.
    > ACPI: IRQ9 used by override.
    > ACPI: IRQ10 used by override.
    > ACPI: IRQ11 used by override.
    > Using ACPI (MADT) for SMP configuration information
    > ACPI: HPET id: 0x8086a201 base: 0xfed00000
    > SMP: Allowing 2 CPUs, 0 hotplug CPUs
    > nr_irqs_gsi: 40
    > PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    > PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000
    > PM: Registered nosave memory: 00000000000f0000 - 0000000000100000
    > Allocating PCI resources starting at 3e800000 (gap: 3e800000:c17bc000)
    > setup_percpu: NR_CPUS:4 nr_cpumask_bits:4 nr_cpu_ids:2 nr_node_ids:1
    > PERCPU: Embedded 26 pages/cpu @ffff880001a00000 s76352 r8192 d21952 u1048576
    > pcpu-alloc: s76352 r8192 d21952 u1048576 alloc=1*2097152
    > pcpu-alloc: [0] 0 1
    > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 252285
    > Kernel command line: root=/dev/sda1 resume=/dev/sdb debug
    > no_console_suspend console=ttyS0,115200 console=tty0 printk.time=1 2
    > PID hash table entries: 4096 (order: 3, 32768 bytes)
    > Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
    > Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
    > Checking aperture...
    > No AGP bridge found
    > Memory: 988644k/1023980k available (5634k kernel code, 392k absent,
    > 34944k reserved, 3013k data, 424k init)
    > SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
    > Hierarchical RCU implementation.
    > RCU-based detection of stalled CPUs is disabled.
    > Verbose stalled-CPUs detection is disabled.
    > NR_IRQS:4352 nr_irqs:512
    > Console: colour VGA+ 80x25
    > console [tty0] enabled
    > console [ttyS0] enabled
    > allocated 10485760 bytes of page_cgroup
    > please try 'cgroup_disable=memory' option if you don't want memory cgroups
    > hpet clockevent registered
    > Fast TSC calibration using PIT
    > Detected 2990.792 MHz processor.
    > Calibrating delay loop (skipped), value calculated using timer
    > frequency.. 5981.58 BogoMIPS (lpj=11963168)
    > pid_max: default: 32768 minimum: 301
    > Mount-cache hash table entries: 256
    > Initializing cgroup subsys debug
    > Initializing cgroup subsys ns
    > Initializing cgroup subsys cpuacct
    > Initializing cgroup subsys memory
    > Initializing cgroup subsys devices
    > Initializing cgroup subsys freezer
    > mce: CPU supports 10 MCE banks
    > Performance Events: unsupported p6 CPU model 2 no PMU driver, software
    > events only.
    > ACPI: Core revision 20100428
    > Setting APIC routing to flat
    > ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    > CPU0: Intel QEMU Virtual CPU version 0.12.3 stepping 03
    > NMI watchdog failed to create perf event on cpu0: ffffffffffffffed
    > Booting Node 0, Processors #1 Ok.
    > NMI watchdog failed to create perf event on cpu1: ffffffffffffffed
    > Brought up 2 CPUs
    > Total of 2 processors activated (11949.21 BogoMIPS).
    > devtmpfs: initialized
    > NET: Registered protocol family 16
    > ACPI: bus type pci registered
    > PCI: Using configuration type 1 for base access
    > mtrr: your CPUs had inconsistent variable MTRR settings
    > mtrr: your CPUs had inconsistent MTRRdefType settings
    > mtrr: probably your BIOS does not setup all CPUs.
    > mtrr: corrected configuration.
    > bio: create slab <bio-0> at 0
    > ACPI: EC: Look up EC in DSDT
    > ACPI: Interpreter enabled
    > ACPI: (supports S0 S3 S4 S5)
    > ACPI: Using IOAPIC for interrupt routing
    > ACPI: No dock devices found.
    > PCI: Ignoring host bridge windows from ACPI; if necessary, use
    > "pci=use_crs" and report a bug
    > ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    > pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored)
    > pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored)
    > pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
    > (ignored)
    > pci_root PNP0A03:00: host bridge window [mem 0xe0000000-0xfebfffff]
    > (ignored)
    > pci 0000:00:01.1: reg 20: [io 0xc000-0xc00f]
    > pci 0000:00:01.2: reg 20: [io 0xc020-0xc03f]
    > pci 0000:00:01.3: quirk: [io 0xb000-0xb03f] claimed by PIIX4 ACPI
    > pci 0000:00:01.3: quirk: [io 0xb100-0xb10f] claimed by PIIX4 SMB
    > pci 0000:00:02.0: reg 10: [mem 0xf0000000-0xf1ffffff pref]
    > pci 0000:00:02.0: reg 14: [mem 0xf2000000-0xf2000fff]
    > pci 0000:00:02.0: reg 30: [mem 0xf2010000-0xf201ffff pref]
    > pci 0000:00:03.0: reg 10: [mem 0xf2020000-0xf203ffff]
    > pci 0000:00:03.0: reg 14: [io 0xc040-0xc07f]
    > pci 0000:00:03.0: reg 30: [mem 0xf2040000-0xf205ffff pref]
    > pci_bus 0000:00: on NUMA node 0
    > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    > ACPI: PCI Interrupt Link [LNKA] (IRQs 5 *10 11)
    > ACPI: PCI Interrupt Link [LNKB] (IRQs 5 *10 11)
    > ACPI: PCI Interrupt Link [LNKC] (IRQs 5 10 *11)
    > ACPI: PCI Interrupt Link [LNKD] (IRQs 5 10 *11)
    > vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    > vgaarb: loaded
    > SCSI subsystem initialized
    > libata version 3.00 loaded.
    > usbcore: registered new interface driver usbfs
    > usbcore: registered new interface driver hub
    > usbcore: registered new device driver usb
    > Advanced Linux Sound Architecture Driver Version 1.0.23.
    > PCI: Using ACPI for IRQ routing
    > PCI: pci_cache_line_size set to 64 bytes
    > reserve RAM buffer: 000000000009f000 - 000000000009ffff
    > reserve RAM buffer: 000000003e7fb000 - 000000003fffffff
    > cfg80211: Calling CRDA to update world regulatory domain
    > HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    > hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    > hpet0: 3 comparators, 64-bit 100.000000 MHz counter
    > Switching to clocksource tsc
    > Slow work thread pool: Starting up
    > Slow work thread pool: Ready
    > FS-Cache: Loaded
    > CacheFiles: Loaded
    > pnp: PnP ACPI init
    > ACPI: bus type pnp registered
    > pnp: PnP ACPI: found 8 devices
    > ACPI: ACPI bus type pnp unregistered
    > pci_bus 0000:00: resource 0 [io 0x0000-0xffff]
    > pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffffffffffff]
    > NET: Registered protocol family 2
    > IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
    > TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
    > TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
    > TCP: Hash tables configured (established 131072 bind 65536)
    > TCP reno registered
    > UDP hash table entries: 512 (order: 2, 16384 bytes)
    > UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    > NET: Registered protocol family 1
    > RPC: Registered udp transport module.
    > RPC: Registered tcp transport module.
    > RPC: Registered tcp NFSv4.1 backchannel transport module.
    > pci 0000:00:00.0: Limiting direct PCI/PCI transfers
    > pci 0000:00:01.0: PIIX3: Enabling Passive Release
    > pci 0000:00:01.0: Activating ISA DMA hang workarounds
    > pci 0000:00:02.0: Boot video device
    > PCI: CLS 0 bytes, default 64
    > Unpacking initramfs...
    > Freeing initrd memory: 8964k freed
    > kvm: no hardware support
    > fuse init (API version 7.13)
    > msgmni has been set to 1948
    > alg: No test for stdrng (krng)
    > io scheduler noop registered
    > io scheduler cfq registered (default)
    > input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
    > ACPI: Power Button [PWRF]
    > Linux agpgart interface v0.103
    > Hangcheck: starting hangcheck timer 0.9.1 (tick is 180 seconds, margin
    > is 60 seconds).
    > Hangcheck: Using getrawmonotonic().
    > [drm] Initialized drm 1.1.0 20060810
    > [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module!
    > Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
    > serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    > 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    > parport_pc 00:05: reported by Plug and Play ACPI
    > parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
    > FDC 0 is a S82078B
    > loop: module loaded
    > ata_piix 0000:00:01.1: version 2.13
    > ata_piix 0000:00:01.1: setting latency timer to 64
    > scsi0 : ata_piix
    > scsi1 : ata_piix
    > ata1: PATA max MWDMA2 cmd 0x1f0 ctl 0x3f6 bmdma 0xc000 irq 14
    > ata2: PATA max MWDMA2 cmd 0x170 ctl 0x376 bmdma 0xc008 irq 15
    > e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k6-NAPI
    > e1000: Copyright (c) 1999-2006 Intel Corporation.
    > ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
    > e1000 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, high) ->
    > IRQ 11
    > e1000 0000:00:03.0: setting latency timer to 64
    > ata1.00: ATA-7: QEMU HARDDISK, 0.12.3, max UDMA/100
    > ata1.00: 20971520 sectors, multi 16: LBA48
    > ata1.01: ATA-7: QEMU HARDDISK, 0.12.3, max UDMA/100
    > ata1.01: 1433602 sectors, multi 16: LBA48
    > ata2.01: NODEV after polling detection
    > ata2.00: ATAPI: QEMU DVD-ROM, 0.12.3, max UDMA/100
    > ata2.00: configured for MWDMA2
    > ata1.00: configured for MWDMA2
    > ata1.01: configured for MWDMA2
    > scsi 0:0:0:0: Direct-Access ATA QEMU HARDDISK 0.12 PQ: 0 ANSI: 5
    > scsi 0:0:1:0: Direct-Access ATA QEMU HARDDISK 0.12 PQ: 0 ANSI: 5
    > sd 0:0:0:0: [sda] 20971520 512-byte logical blocks: (10.7 GB/10.0 GiB)
    > scsi 1:0:0:0: CD-ROM QEMU QEMU DVD-ROM 0.12 PQ: 0 ANSI: 5
    > sd 0:0:0:0: [sda] Write Protect is off
    > sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    > sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't
    > support DPO or FUA
    > sd 0:0:1:0: [sdb] 1433602 512-byte logical blocks: (734 MB/700 MiB)
    > sda:sr0: scsi3-mmc drive: 4x/4x xa/form2 tray
    > Uniform CD-ROM driver Revision: 3.20
    > sda1
    > sd 0:0:1:0: [sdb] Write Protect is off
    > sr 1:0:0:0: Attached scsi CD-ROM sr0
    > sd 0:0:0:0: [sda] Attached SCSI disk
    > sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00
    > sd 0:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't
    > support DPO or FUA
    > sdb: unknown partition table
    > sd 0:0:1:0: [sdb] Attached SCSI disk
    > e1000 0000:00:03.0: eth0: (PCI:33MHz:32-bit)
    > e1000 0000:00:03.0: eth0: 52:54:00:12:34:56
    > e1000 0000:00:03.0: eth0: Intel(R) PRO/1000 Network Connection
    > e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4
    > e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
    > tun: Universal TUN/TAP device driver, 1.6
    > tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
    > console [netcon0] enabled
    > netconsole: network logging started
    > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    > uhci_hcd: USB Universal Host Controller Interface driver
    > ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
    > uhci_hcd 0000:00:01.2: PCI INT D -> Link[LNKD] -> GSI 10 (level, high)
    > -> IRQ 10
    > uhci_hcd 0000:00:01.2: setting latency timer to 64
    > uhci_hcd 0000:00:01.2: UHCI Host Controller
    > uhci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
    > uhci_hcd 0000:00:01.2: irq 10, io base 0x0000c020
    > hub 1-0:1.0: USB hub found
    > hub 1-0:1.0: 2 ports detected
    > PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
    > serio: i8042 KBD port at 0x60,0x64 irq 1
    > serio: i8042 AUX port at 0x60,0x64 irq 12
    > mice: PS/2 mouse device common for all mice
    > input: AT Translated Set 2 keyboard as
    > /devices/platform/i8042/serio0/input/input1
    > rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
    > rtc0: alarms up to one day, 114 bytes nvram, hpet irqs
    > i2c /dev entries driver
    > coretemp: CPU (model=0x2) has no thermal sensor.
    > coretemp: CPU (model=0x2) has no thermal sensor.
    > md: raid0 personality registered for level 0
    > md: raid1 personality registered for level 1
    > device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised:
    > dm-devel@redhat.com
    > cpuidle: using governor ladder
    > cpuidle: using governor menu
    > Registered led device: input::numl
    > Registered led device: input::capsl
    > Registered led device: input::scrolll
    > Registered led device: input1::numl
    > Registered led device: input1::capsl
    > Registered led device: input1::scrolll
    > usbcore: registered new interface driver usbhid
    > usbhid: USB HID core driver
    > ALSA device list:
    > No soundcards found.
    > TCP cubic registered
    > NET: Registered protocol family 10
    > NET: Registered protocol family 17
    > registered taskstats version 1
    > rtc_cmos 00:01: setting system clock to 2010-06-01 14:42:57 UTC (1275403377)
    > Freeing unused kernel memory: 424k freed
    > Write protecting the kernel read-only data: 8192k
    > Freeing unused kernel memory: 488k freed
    > Freeing unused kernel memory: 328k freed
    > udev: starting version 154
    > PM: Starting manual resume from disk
    > EXT4-fs (sda1): (no)acl options not supported
    > EXT4-fs (sda1): mounted filesystem with ordered data mode
    > EXT4-fs (sda1): (no)acl options not supported
    > udev: starting version 154
    > Adding 716796k swap on /dev/sdb. Priority:-1 extents:1 across:716796k
    > ADDRCONF(NETDEV_UP): eth0: link is not ready
    > e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
    > ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
    > Syncing filesystems ... done.
    > Freezing user space processes ... (elapsed 0.01 seconds) done.
    > Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
    > PM: Preallocating image memory... done (allocated 28778 pages)
    > PM: Allocated 115112 kbytes in 0.03 seconds (3837.06 MB/s)
    > e1000 0000:00:03.0: PCI INT A disabled
    > PM: freeze of devices complete after 54.045 msecs
    > PM: late freeze of devices complete after 0.614 msecs
    > ACPI: Preparing to enter system sleep state S4
    > PM: Saving platform NVS memory
    > Disabling non-boot CPUs ...
    > Broke affinity for irq 14
    > CPU 1 is now offline
    > SMP alternatives: switching to UP code
    > PM: Creating hibernation image:
    > PM: Need to copy 28341 pages
    > PM: Hibernation image created (28341 pages copied)
    > Enabling non-boot CPUs ...
    > SMP alternatives: switching to SMP code
    > Booting Node 0 Processor 1 APIC 0x1
    > NMI watchdog failed to create perf event on cpu1: ffffffffffffffed
    > CPU1 is up
    > ACPI: Waking up from system sleep state S4
    > PM: early thaw of devices complete after 0.025 msecs
    > ata_piix 0000:00:01.1: restoring config space at offset 0x1 (was
    > 0x2800003, writing 0x2800007)
    > e1000 0000:00:03.0: restoring config space at offset 0x1 (was 0x100003,
    > writing 0x100007)
    > e1000 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, high) ->
    > IRQ 11
    > e1000 0000:00:03.0: setting latency timer to 64
    > ata_piix 0000:00:01.1: setting latency timer to 64
    > sd 0:0:0:0: [sda] Starting disk
    > sd 0:0:1:0: [sdb] Starting disk
    > e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
    > ata1.00: configured for MWDMA2
    > ata1.01: configured for MWDMA2
    > PM: thaw of devices complete after 166.297 msecs
    > PM: Saving image data pages (28397 pages) ... done
    > PM: Wrote 113588 kbytes in 2.95 seconds (38.50 MB/s)
    > ata2.01: qc timeout (cmd 0xec)
    > ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
    > sd 0:0:1:0: [sdb] Stopping disk
    > sd 0:0:0:0: [sda] Stopping disk
    > uhci_hcd 0000:00:01.2: PCI INT D disabled
    > e1000 0000:00:03.0: PCI INT A disabled
    > ata2.01: qc timeout (cmd 0xec)
    > ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
    >
    >
    > --
    > js


    \
     
     \ /
      Last update: 2010-06-01 17:29    [W:0.062 / U:63.456 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site