lkml.org 
[lkml]   [2010]   [Apr]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    Subjectboot device order troubleshooting without an initrd
    Hi folks,
    I'm looking for a way to pass a correct "root" parameter to the kernel
    from the bootloader, independently on the number of attached disks. My
    machine (VIA EPIA SN-1800) has four SATA ports and one CF card slot. The
    CF slot is visible as an IDE device. The BIOS is configured for booting
    from the CF card, and Grub2 has absolutely no problems booting the kernel.

    The problem I'm facing is that if there are no SATA disks attached, my
    CF card gets called /dev/sda, while if I attach two SATA drives, the CF
    card gets called /dev/sdc. I can solve that "in userspace" without much
    problem thanks to udev's names like
    /dev/disk/by-id/scsi-SATA_ELITE_PRO_CF_..., but I have no idea about how
    to pass the correct "root" argument to the kernel. If I use
    "root=/dev/sda1", kernel will boot if and only if I don't have any SATA
    devices attached; on the other hand, having two SATA drives attached
    requires "root=/dev/sdc1". I've tried to use the by-id naming, but it is
    apparently provided by udev much later in the "boot process", and the
    document by gregkh [1] doesn't mention it, either.

    I have disabled modules, and don't use initrd. Such a setup has worked
    for me for a few years. Not having modules enabled makes me feel
    "safer", and I have not ever needed an initrd, so far. If I was using
    initrd, I'd probably be able to use the "root=LABEL=foo" stuff.

    Relevant part of `lspci`:

    00:0f.0 SATA controller: VIA Technologies, Inc. SATA RAID Controller
    (rev 20)
    00:0f.1 IDE interface: VIA Technologies, Inc.
    VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 07)

    I'm attaching full dmesg, as the output seems to be interleaved from
    more drivers, and I'm afraid I'd skip something if I tried to include
    only relevant parts. The kernel I'm using is 2.6.32-gentoo-r1.

    What I'm looking for is an advice if it's possible to tell kernel to
    "use the BIOS-provided HDD ordering". I suspect I'm likely going to be
    told "you are supposed to use initrd"; if that is the case, I'd love to
    see a technical argument about why.

    Anyway, I'm looking for any input. I'd much appreciate if you could Cc
    me on replies, as I'm not subscribed to the list.

    Have fun,
    -jkt

    [1]
    http://www.kernel.org/pub/linux/kernel/people/gregkh/lkn/lkn_pdf/ch09.pdf

    --
    cd /local/pub && more beer > /dev/mouth
    Linux version 2.6.32-gentoo-r1 (root@plejtvak) (gcc version 4.3.4 (Gentoo 4.3.4 p1.0, pie-10.1.5) ) #2 Wed Apr 14 01:29:36 CEST 2010
    KERNEL supported cpus:
    Intel GenuineIntel
    AMD AuthenticAMD
    NSC Geode by NSC
    Cyrix CyrixInstead
    Centaur CentaurHauls
    Transmeta GenuineTMx86
    Transmeta TransmetaCPU
    UMC UMC UMC UMC
    BIOS-provided physical RAM map:
    BIOS-e820: 0000000000000000 - 000000000009b400 (usable)
    BIOS-e820: 000000000009b400 - 00000000000a0000 (reserved)
    BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
    BIOS-e820: 0000000000100000 - 00000000dbeb0000 (usable)
    BIOS-e820: 00000000dbeb0000 - 00000000dbebe000 (ACPI data)
    BIOS-e820: 00000000dbebe000 - 00000000dbf00000 (ACPI NVS)
    BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
    BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved)
    BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
    DMI 2.3 present.
    AMI BIOS detected: BIOS may corrupt low RAM, working around it.
    e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    last_pfn = 0xdbeb0 max_arch_pfn = 0x100000
    MTRR default type: uncachable
    MTRR fixed ranges enabled:
    00000-9FFFF write-back
    A0000-DFFFF uncachable
    E0000-E3FFF write-protect
    E4000-EFFFF write-through
    F0000-FFFFF write-protect
    MTRR variable ranges enabled:
    0 base 000000000 mask F80000000 write-back
    1 base 080000000 mask FC0000000 write-back
    2 base 0C0000000 mask FF0000000 write-back
    3 base 0D0000000 mask FF8000000 write-back
    4 base 0D8000000 mask FFC000000 write-back
    5 base 0DBF00000 mask FFFF00000 uncachable
    6 disabled
    7 disabled
    x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    initial memory mapped : 0 - 01c00000
    init_memory_mapping: 0000000000000000-00000000377fe000
    0000000000 - 0000400000 page 4k
    0000400000 - 0037400000 page 2M
    0037400000 - 00377fe000 page 4k
    kernel direct mapping tables up to 377fe000 @ 10000-15000
    ACPI: RSDP 000f9460 00024 (v02 ACPIAM)
    ACPI: XSDT dbeb0100 0004C (v01 060109 XSDT1205 20090601 MSFT 00000097)
    ACPI: FACP dbeb0290 000F4 (v03 060109 FACP1205 20090601 MSFT 00000097)
    ACPI: DSDT dbeb0430 0459E (v01 1ADTQ 1ADTQ003 00000003 INTL 20051117)
    ACPI: FACS dbebe000 00040
    ACPI: APIC dbeb0390 00060 (v01 060109 APIC1205 20090601 MSFT 00000097)
    ACPI: MCFG dbeb03f0 0003C (v01 060109 OEMMCFG 20090601 MSFT 00000097)
    ACPI: OEMB dbebe040 00061 (v01 060109 OEMB1205 20090601 MSFT 00000097)
    ACPI: SSDT dbebe0b0 0023A (v01 AMI P001PM 00000001 INTL 20051117)
    ACPI: Local APIC address 0xfee00000
    2630MB HIGHMEM available.
    887MB LOWMEM available.
    mapped low ram: 0 - 377fe000
    low ram: 0 - 377fe000
    node 0 low ram: 00000000 - 377fe000
    node 0 bootmap 00011000 - 00017f00
    (6 early reservations) ==> bootmem [0000000000 - 00377fe000]
    #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
    #1 [0001000000 - 00017387c0] TEXT DATA BSS ==> [0001000000 - 00017387c0]
    #2 [000009b400 - 0000100000] BIOS reserved ==> [000009b400 - 0000100000]
    #3 [0001739000 - 00017401c1] BRK ==> [0001739000 - 00017401c1]
    #4 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
    #5 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
    found SMP MP-table at [c00ff780] ff780
    Zone PFN ranges:
    DMA 0x00000010 -> 0x00001000
    Normal 0x00001000 -> 0x000377fe
    HighMem 0x000377fe -> 0x000dbeb0
    Movable zone start PFN for each node
    early_node_map[2] active PFN ranges
    0: 0x00000010 -> 0x0000009b
    0: 0x00000100 -> 0x000dbeb0
    On node 0 totalpages: 900667
    free_area_init_node: node 0, pgdat c1650b60, node_mem_map c1742200
    DMA zone: 32 pages used for memmap
    DMA zone: 0 pages reserved
    DMA zone: 3947 pages, LIFO batch:0
    Normal zone: 1744 pages used for memmap
    Normal zone: 221486 pages, LIFO batch:31
    HighMem zone: 5262 pages used for memmap
    HighMem zone: 668196 pages, LIFO batch:31
    Using APIC driver default
    ACPI: PM-Timer IO Port: 0x808
    ACPI: Local APIC address 0xfee00000
    ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
    ACPI: IOAPIC (id[0x02] address[0xfecc0000] gsi_base[24])
    IOAPIC[1]: apic_id 2, version 3, address 0xfecc0000, GSI 24-47
    ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    ACPI: IRQ0 used by override.
    ACPI: IRQ2 used by override.
    ACPI: IRQ9 used by override.
    Enabling APIC mode: Flat. Using 2 I/O APICs
    Using ACPI (MADT) for SMP configuration information
    nr_irqs_gsi: 48
    Allocating PCI resources starting at dbf00000 (gap: dbf00000:22d00000)
    Built 1 zonelists in Zone order, mobility grouping on. Total pages: 893629
    Kernel command line: BOOT_IMAGE=/boot/bzImage-2.6.32-gentoo-r1 root=/dev/sdc1 ro
    PID hash table entries: 4096 (order: 2, 16384 bytes)
    Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    Enabling fast FPU save and restore... done.
    Enabling unmasked SIMD FPU exception support... done.
    Initializing CPU#0
    Initializing HighMem for node 0 (000377fe:000dbeb0)
    Memory: 3565388k/3603136k available (4911k kernel code, 36424k reserved, 1599k data, 356k init, 2693832k highmem)
    virtual kernel memory layout:
    fixmap : 0xfffa4000 - 0xfffff000 ( 364 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    .init : 0xc165c000 - 0xc16b5000 ( 356 kB)
    .data : 0xc14cbc29 - 0xc165b860 (1599 kB)
    .text : 0xc1000000 - 0xc14cbc29 (4911 kB)
    Checking if this processor honours the WP bit even in supervisor mode...Ok.
    SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
    Hierarchical RCU implementation.
    NR_IRQS:288
    Extended CMOS year: 2000
    Console: colour VGA+ 80x25
    console [tty0] enabled
    Fast TSC calibration using PIT
    Detected 1817.678 MHz processor.
    Calibrating delay loop (skipped), value calculated using timer frequency.. 3635.35 BogoMIPS (lpj=18176780)
    Mount-cache hash table entries: 512
    CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
    CPU: L2 Cache: 128K (64 bytes/line)
    CPU: Centaur VIA C7 Processor 1800MHz stepping 00
    Checking 'hlt' instruction... OK.
    ACPI: Core revision 20090903
    ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    khelper used greatest stack depth: 7452 bytes left
    NET: Registered protocol family 16
    ACPI: bus type pci registered
    PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
    PCI: Not using MMCONFIG.
    PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3
    PCI: Using configuration type 1 for base access
    khelper used greatest stack depth: 7148 bytes left
    bio: create slab <bio-0> at 0
    ACPI: EC: Look up EC in DSDT
    ACPI: Executed 1 blocks of module-level executable AML code
    ACPI: Interpreter enabled
    ACPI: (supports S0 S5)
    ACPI: Using IOAPIC for interrupt routing
    PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
    PCI: MCFG area at e0000000 reserved in ACPI motherboard resources
    PCI: Using MMCONFIG for extended config space
    ACPI: Power Resource [SVPR] (on)
    ACPI Warning: Incorrect checksum in table [OEMB] - 0A, should be 07 (20090903/tbutils-314)
    ACPI: No dock devices found.
    ACPI: PCI Root Bridge [PCI0] (0000:00)
    pci 0000:00:00.0: reg 10 32bit mmio pref: [0xfc000000-0xfdffffff]
    pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:02.0: PME# disabled
    pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
    pci 0000:00:03.0: PME# disabled
    pci 0000:00:0f.0: reg 10 io port: [0xdc00-0xdc07]
    pci 0000:00:0f.0: reg 14 io port: [0xd880-0xd883]
    pci 0000:00:0f.0: reg 18 io port: [0xd800-0xd807]
    pci 0000:00:0f.0: reg 1c io port: [0xd480-0xd483]
    pci 0000:00:0f.0: reg 20 io port: [0xd400-0xd40f]
    pci 0000:00:0f.0: reg 24 32bit mmio: [0xfafffc00-0xfaffffff]
    pci 0000:00:0f.0: PME# supported from D3hot
    pci 0000:00:0f.0: PME# disabled
    pci 0000:00:0f.1: reg 20 io port: [0xfc00-0xfc0f]
    pci 0000:00:10.0: reg 20 io port: [0xcc00-0xcc1f]
    pci 0000:00:10.0: supports D1 D2
    pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:10.0: PME# disabled
    pci 0000:00:10.1: reg 20 io port: [0xd000-0xd01f]
    pci 0000:00:10.1: supports D1 D2
    pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:10.1: PME# disabled
    pci 0000:00:10.2: reg 20 io port: [0xd080-0xd09f]
    pci 0000:00:10.2: supports D1 D2
    pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:10.2: PME# disabled
    pci 0000:00:10.4: reg 10 32bit mmio: [0xfafff800-0xfafff8ff]
    pci 0000:00:10.4: supports D1 D2
    pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:10.4: PME# disabled
    pci 0000:00:12.0: reg 10 io port: [0xc800-0xc8ff]
    pci 0000:00:12.0: reg 14 32bit mmio: [0xfafff400-0xfafff4ff]
    pci 0000:00:12.0: supports D1 D2
    pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:00:12.0: PME# disabled
    pci 0000:01:00.0: reg 10 32bit mmio pref: [0xf4000000-0xf7ffffff]
    pci 0000:01:00.0: reg 14 32bit mmio: [0xfb000000-0xfbffffff]
    pci 0000:01:00.0: reg 30 32bit mmio pref: [0xfe9f0000-0xfe9fffff]
    pci 0000:01:00.0: supports D1 D2
    pci 0000:00:01.0: bridge 32bit mmio: [0xfb000000-0xfe9fffff]
    pci 0000:00:01.0: bridge 32bit mmio pref: [0xf4000000-0xf7ffffff]
    pci 0000:00:02.0: bridge 64bit mmio pref: [0xf9f00000-0xf9ffffff]
    pci 0000:03:00.0: reg 10 io port: [0xe800-0xe8ff]
    pci 0000:03:00.0: reg 14 64bit mmio: [0xfeaffc00-0xfeaffcff]
    pci 0000:03:00.0: supports D1 D2
    pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    pci 0000:03:00.0: PME# disabled
    pci 0000:00:03.0: bridge io port: [0xe000-0xefff]
    pci 0000:00:03.0: bridge 32bit mmio: [0xfea00000-0xfeafffff]
    pci_bus 0000:00: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBPG._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP0._PRT]
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
    ACPI: PCI Root Bridge [PCI1] (0000:80)
    pci 0000:80:00.0: PME# supported from D0 D3hot D3cold
    pci 0000:80:00.0: PME# disabled
    pci 0000:80:00.1: PME# supported from D0 D3hot D3cold
    pci 0000:80:00.1: PME# disabled
    pci 0000:80:01.0: reg 10 32bit mmio: [0xfebfc000-0xfebfffff]
    pci 0000:80:01.0: PME# supported from D0 D3hot D3cold
    pci 0000:80:01.0: PME# disabled
    pci_bus 0000:80: on NUMA node 0
    ACPI: PCI Interrupt Routing Table [\_SB_.PCI1._PRT]
    ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
    ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    vgaarb: loaded
    SCSI subsystem initialized
    libata version 3.00 loaded.
    usbcore: registered new interface driver usbfs
    usbcore: registered new interface driver hub
    usbcore: registered new device driver usb
    PCI: Using ACPI for IRQ routing
    pci 0000:00:00.0: BAR 0: address space collision on of device [0xfc000000-0xfdffffff]
    pci 0000:00:00.0: BAR 0: can't allocate resource
    Switching to clocksource tsc
    pnp: PnP ACPI init
    ACPI: bus type pnp registered
    pnp 00:05: IRQ 3 override to edge, high
    pnp 00:06: IRQ 3 override to edge, high
    pnp 00:0b: mem resource (0x0-0x9ffff) overlaps 0000:00:00.0 BAR 0 (0x0-0x1ffffff), disabling
    pnp 00:0b: mem resource (0xc0000-0xcffff) overlaps 0000:00:00.0 BAR 0 (0x0-0x1ffffff), disabling
    pnp 00:0b: mem resource (0xe0000-0xfffff) overlaps 0000:00:00.0 BAR 0 (0x0-0x1ffffff), disabling
    pnp 00:0b: mem resource (0x100000-0xdbefffff) overlaps 0000:00:00.0 BAR 0 (0x0-0x1ffffff), disabling
    pnp: PnP ACPI: found 13 devices
    ACPI: ACPI bus type pnp unregistered
    system 00:07: ioport range 0x162e-0x162f has been reserved
    system 00:07: ioport range 0xa00-0xa7f has been reserved
    system 00:08: ioport range 0x3e0-0x3e7 has been reserved
    system 00:08: ioport range 0x4d0-0x4d1 has been reserved
    system 00:08: ioport range 0x800-0x87f has been reserved
    system 00:08: ioport range 0x400-0x41f has been reserved
    system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
    system 00:09: iomem range 0xfec00000-0xfec00fff could not be reserved
    system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
    system 00:0a: iomem range 0xe0000000-0xefffffff has been reserved
    system 00:0b: iomem range 0xfec00000-0xffffffff could not be reserved
    pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
    pci 0000:00:01.0: IO window: disabled
    pci 0000:00:01.0: MEM window: 0xfb000000-0xfe9fffff
    pci 0000:00:01.0: PREFETCH window: 0xf4000000-0xf7ffffff
    pci 0000:00:02.0: PCI bridge, secondary bus 0000:02
    pci 0000:00:02.0: IO window: 0x2000-0x2fff
    pci 0000:00:02.0: MEM window: 0xdc000000-0xdc3fffff
    pci 0000:00:02.0: PREFETCH window: 0x000000f9f00000-0x000000f9ffffff
    pci 0000:00:03.0: PCI bridge, secondary bus 0000:03
    pci 0000:00:03.0: IO window: 0xe000-0xefff
    pci 0000:00:03.0: MEM window: 0xfea00000-0xfeafffff
    pci 0000:00:03.0: PREFETCH window: 0x000000dc400000-0x000000dc5fffff
    pci 0000:00:01.0: setting latency timer to 64
    pci 0000:00:02.0: enabling device (0106 -> 0107)
    pci 0000:00:02.0: PCI INT A -> GSI 27 (level, low) -> IRQ 27
    pci 0000:00:02.0: setting latency timer to 64
    pci 0000:00:03.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31
    pci 0000:00:03.0: setting latency timer to 64
    pci 0000:80:00.0: PCI bridge, secondary bus 0000:82
    pci 0000:80:00.0: IO window: disabled
    pci 0000:80:00.0: MEM window: disabled
    pci 0000:80:00.0: PREFETCH window: disabled
    pci 0000:80:00.1: PCI bridge, secondary bus 0000:81
    pci 0000:80:00.1: IO window: disabled
    pci 0000:80:00.1: MEM window: disabled
    pci 0000:80:00.1: PREFETCH window: disabled
    pci 0000:80:00.0: setting latency timer to 64
    pci 0000:80:00.1: setting latency timer to 64
    pci_bus 0000:00: resource 0 io: [0x00-0xffff]
    pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
    pci_bus 0000:01: resource 1 mem: [0xfb000000-0xfe9fffff]
    pci_bus 0000:01: resource 2 pref mem [0xf4000000-0xf7ffffff]
    pci_bus 0000:02: resource 0 io: [0x2000-0x2fff]
    pci_bus 0000:02: resource 1 mem: [0xdc000000-0xdc3fffff]
    pci_bus 0000:02: resource 2 pref mem [0xf9f00000-0xf9ffffff]
    pci_bus 0000:03: resource 0 io: [0xe000-0xefff]
    pci_bus 0000:03: resource 1 mem: [0xfea00000-0xfeafffff]
    pci_bus 0000:03: resource 2 pref mem [0xdc400000-0xdc5fffff]
    pci_bus 0000:80: resource 0 io: [0x00-0xffff]
    pci_bus 0000:80: resource 1 mem: [0x000000-0xffffffff]
    NET: Registered protocol family 2
    IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
    TCP: Hash tables configured (established 131072 bind 65536)
    TCP reno registered
    NET: Registered protocol family 1
    RPC: Registered udp transport module.
    RPC: Registered tcp transport module.
    RPC: Registered tcp NFSv4.1 backchannel transport module.
    pci 0000:00:00.0: MSI quirk detected; MSI disabled
    pci 0000:00:01.0: disabling DAC on VIA PCI bridge
    pci 0000:00:10.0: uhci_check_and_reset_hc: legsup = 0x8030
    pci 0000:00:10.0: Performing full reset
    pci 0000:00:10.1: uhci_check_and_reset_hc: legsup = 0x8030
    pci 0000:00:10.1: Performing full reset
    pci 0000:00:10.2: uhci_check_and_reset_hc: legsup = 0x8030
    pci 0000:00:10.2: Performing full reset
    pci 0000:00:10.4: EHCI: BIOS handoff
    pci 0000:01:00.0: Boot video device
    eps: Detected VIA Model D C7
    eps: Current voltage = 1196mV
    eps: Current multiplier = 9
    eps: Highest voltage = 1196mV
    eps: Highest multiplier = 9
    eps: Lowest voltage = 956mV
    eps: Lowest multiplier = 4
    microcode: no support for this CPU vendor
    audit: initializing netlink socket (disabled)
    type=2000 audit(1271627252.332:1): initialized
    highmem bounce pool size: 64 pages
    HugeTLB registered 4 MB page size, pre-allocated 0 pages
    khelper used greatest stack depth: 7144 bytes left
    Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
    Slow work thread pool: Starting up
    Slow work thread pool: Ready
    NTFS driver 2.1.29 [Flags: R/W].
    SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
    msgmni has been set to 1703
    cryptomgr_test used greatest stack depth: 6868 bytes left
    cryptomgr_test used greatest stack depth: 6344 bytes left
    alg: No test for stdrng (krng)
    Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    io scheduler noop registered
    io scheduler cfq registered (default)
    pcieport 0000:00:02.0: setting latency timer to 64
    pcieport 0000:00:03.0: setting latency timer to 64
    pcieport 0000:80:00.0: setting latency timer to 64
    pcieport 0000:80:00.1: setting latency timer to 64
    Non-volatile memory driver v1.3
    VIA RNG detected
    input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
    ACPI: Sleep Button [SLPB]
    input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
    ACPI: Power Button [PWRB]
    input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
    ACPI: Power Button [PWRF]
    processor LNXCPU:00: registered as cooling_device0
    Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
    Marking TSC unstable due to cpufreq changes
    Switching to clocksource acpi_pm
    serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
    serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    00:05: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
    00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
    brd: module loaded
    loop: module loaded
    Loading iSCSI transport class v2.0-870.
    ahci 0000:00:0f.0: version 3.0
    ahci 0000:00:0f.0: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    ahci 0000:00:0f.0: controller can't do NCQ, turning off CAP_NCQ
    ahci 0000:00:0f.0: controller can't do PMP, turning off CAP_PMP
    ahci 0000:00:0f.0: PCI: Disallowing DAC for device
    ahci 0000:00:0f.0: AHCI 0001.0000 32 slots 4 ports 3 Gbps 0xf impl SATA mode
    ahci 0000:00:0f.0: flags: 64bit pm led clo pio slum part
    scsi0 : ahci
    scsi1 : ahci
    scsi2 : ahci
    scsi3 : ahci
    ata1: SATA max UDMA/133 abar m1024@0xfafffc00 port 0xfafffd00 irq 21
    ata2: SATA max UDMA/133 abar m1024@0xfafffc00 port 0xfafffd80 irq 21
    ata3: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 21
    ata4: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 21
    pata_via 0000:00:0f.1: version 0.3.4
    scsi4 : pata_via
    scsi5 : pata_via
    ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
    ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
    via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
    via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
    eth0: VIA Rhine II at 0xfafff400, 00:40:63:fa:c8:e8, IRQ 23.
    eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
    VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.14
    Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
    Copyright (c) 2004 Red Hat Inc.
    via-velocity 0000:03:00.0: PCI INT A -> GSI 28 (level, low) -> IRQ 28
    via-velocity 0000:03:00.0: setting latency timer to 64
    eth1: VIA Networking Velocity Family Gigabit Ethernet Adapter
    eth1: Ethernet Address: 00:40:63:FA:C8:E9
    ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
    ehci_hcd 0000:00:10.4: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    ehci_hcd 0000:00:10.4: EHCI Host Controller
    drivers/usb/core/inode.c: creating file 'devices'
    drivers/usb/core/inode.c: creating file '001'
    ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
    ehci_hcd 0000:00:10.4: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
    ehci_hcd 0000:00:10.4: reset hcc_params 6872 thresh 7 uframes 256/512/1024
    ehci_hcd 0000:00:10.4: debug port 1
    ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
    ehci_hcd 0000:00:10.4: MWI active
    ehci_hcd 0000:00:10.4: supports USB remote wakeup
    ehci_hcd 0000:00:10.4: irq 22, io mem 0xfafff800
    ehci_hcd 0000:00:10.4: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT
    ehci_hcd 0000:00:10.4: init command 010009 (park)=0 ithresh=1 period=256 RUN
    ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
    usb usb1: default language 0x0409
    usb usb1: udev 1, busnum 1, minor = 0
    usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
    usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb1: Product: EHCI Host Controller
    usb usb1: Manufacturer: Linux 2.6.32-gentoo-r1 ehci_hcd
    usb usb1: SerialNumber: 0000:00:10.4
    usb usb1: uevent
    usb usb1: usb_probe_device
    usb usb1: configuration #1 chosen from 1 choice
    usb usb1: adding 1-0:1.0 (config #1, interface 0)
    usb 1-0:1.0: uevent
    hub 1-0:1.0: usb_probe_interface
    hub 1-0:1.0: usb_probe_interface - got id
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 6 ports detected
    hub 1-0:1.0: standalone hub
    hub 1-0:1.0: no power switching (usb 1.0)
    hub 1-0:1.0: individual port over-current protection
    hub 1-0:1.0: power on to power good time: 20ms
    hub 1-0:1.0: local power source is good
    hub 1-0:1.0: trying to enable port power on non-switchable hub
    drivers/usb/core/inode.c: creating file '001'
    uhci_hcd: USB Universal Host Controller Interface driver
    uhci_hcd 0000:00:10.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
    uhci_hcd 0000:00:10.0: UHCI Host Controller
    drivers/usb/core/inode.c: creating file '002'
    uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
    uhci_hcd 0000:00:10.0: detected 2 ports
    uhci_hcd 0000:00:10.0: uhci_check_and_reset_hc: cmd = 0x0000
    uhci_hcd 0000:00:10.0: Performing full reset
    uhci_hcd 0000:00:10.0: supports USB remote wakeup
    uhci_hcd 0000:00:10.0: irq 20, io base 0x0000cc00
    usb usb2: default language 0x0409
    usb usb2: udev 1, busnum 2, minor = 128
    usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb2: Product: UHCI Host Controller
    usb usb2: Manufacturer: Linux 2.6.32-gentoo-r1 uhci_hcd
    usb usb2: SerialNumber: 0000:00:10.0
    usb usb2: uevent
    usb usb2: usb_probe_device
    usb usb2: configuration #1 chosen from 1 choice
    usb usb2: adding 2-0:1.0 (config #1, interface 0)
    usb 2-0:1.0: uevent
    hub 2-0:1.0: usb_probe_interface
    hub 2-0:1.0: usb_probe_interface - got id
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 2 ports detected
    hub 2-0:1.0: standalone hub
    hub 2-0:1.0: no power switching (usb 1.0)
    hub 2-0:1.0: individual port over-current protection
    hub 2-0:1.0: power on to power good time: 2ms
    hub 2-0:1.0: local power source is good
    hub 2-0:1.0: trying to enable port power on non-switchable hub
    drivers/usb/core/inode.c: creating file '001'
    uhci_hcd 0000:00:10.1: PCI INT C -> GSI 22 (level, low) -> IRQ 22
    uhci_hcd 0000:00:10.1: UHCI Host Controller
    drivers/usb/core/inode.c: creating file '003'
    uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
    uhci_hcd 0000:00:10.1: detected 2 ports
    uhci_hcd 0000:00:10.1: uhci_check_and_reset_hc: cmd = 0x0000
    uhci_hcd 0000:00:10.1: Performing full reset
    uhci_hcd 0000:00:10.1: supports USB remote wakeup
    uhci_hcd 0000:00:10.1: irq 22, io base 0x0000d000
    usb usb3: default language 0x0409
    usb usb3: udev 1, busnum 3, minor = 256
    usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb3: Product: UHCI Host Controller
    usb usb3: Manufacturer: Linux 2.6.32-gentoo-r1 uhci_hcd
    usb usb3: SerialNumber: 0000:00:10.1
    usb usb3: uevent
    usb usb3: usb_probe_device
    usb usb3: configuration #1 chosen from 1 choice
    usb usb3: adding 3-0:1.0 (config #1, interface 0)
    usb 3-0:1.0: uevent
    hub 3-0:1.0: usb_probe_interface
    hub 3-0:1.0: usb_probe_interface - got id
    hub 3-0:1.0: USB hub found
    hub 3-0:1.0: 2 ports detected
    hub 3-0:1.0: standalone hub
    hub 3-0:1.0: no power switching (usb 1.0)
    hub 3-0:1.0: individual port over-current protection
    hub 3-0:1.0: power on to power good time: 2ms
    hub 3-0:1.0: local power source is good
    hub 3-0:1.0: trying to enable port power on non-switchable hub
    drivers/usb/core/inode.c: creating file '001'
    uhci_hcd 0000:00:10.2: PCI INT B -> GSI 21 (level, low) -> IRQ 21
    uhci_hcd 0000:00:10.2: UHCI Host Controller
    drivers/usb/core/inode.c: creating file '004'
    uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
    uhci_hcd 0000:00:10.2: detected 2 ports
    uhci_hcd 0000:00:10.2: uhci_check_and_reset_hc: cmd = 0x0000
    uhci_hcd 0000:00:10.2: Performing full reset
    uhci_hcd 0000:00:10.2: supports USB remote wakeup
    uhci_hcd 0000:00:10.2: irq 21, io base 0x0000d080
    usb usb4: default language 0x0409
    usb usb4: udev 1, busnum 4, minor = 384
    usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
    usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
    usb usb4: Product: UHCI Host Controller
    usb usb4: Manufacturer: Linux 2.6.32-gentoo-r1 uhci_hcd
    usb usb4: SerialNumber: 0000:00:10.2
    usb usb4: uevent
    usb usb4: usb_probe_device
    usb usb4: configuration #1 chosen from 1 choice
    usb usb4: adding 4-0:1.0 (config #1, interface 0)
    usb 4-0:1.0: uevent
    hub 4-0:1.0: usb_probe_interface
    hub 4-0:1.0: usb_probe_interface - got id
    hub 4-0:1.0: USB hub found
    hub 4-0:1.0: 2 ports detected
    hub 4-0:1.0: standalone hub
    hub 4-0:1.0: no power switching (usb 1.0)
    hub 4-0:1.0: individual port over-current protection
    hub 4-0:1.0: power on to power good time: 2ms
    hub 4-0:1.0: local power source is good
    hub 4-0:1.0: trying to enable port power on non-switchable hub
    drivers/usb/core/inode.c: creating file '001'
    usbcore: registered new interface driver usblp
    Initializing USB Mass Storage driver...
    usbcore: registered new interface driver usb-storage
    USB Mass Storage support registered.
    usbcore: registered new interface driver libusual
    PNP: No PS/2 controller found. Probing ports directly.
    serio: i8042 KBD port at 0x60,0x64 irq 1
    serio: i8042 AUX port at 0x60,0x64 irq 12
    mice: PS/2 mouse device common for all mice
    Driver 'rtc_cmos' needs updating - please use bus_type methods
    rtc_cmos 00:02: RTC can wake from S4
    rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
    rtc0: alarms up to one year, y3k, 114 bytes nvram
    device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
    cpuidle: using governor ladder
    cpuidle: using governor menu
    padlock: Using VIA PadLock ACE for AES algorithm.
    padlock: Using VIA PadLock ACE for SHA1/SHA256 algorithms.
    usbcore: registered new interface driver hiddev
    usbcore: registered new interface driver usbhid
    usbhid: v2.6:USB HID core driver
    Advanced Linux Sound Architecture Driver Version 1.0.21.
    ALSA device list:
    No soundcards found.
    Netfilter messages via NETLINK v0.30.
    nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
    ctnetlink v0.93: registering with nfnetlink.
    ip_tables: (C) 2000-2006 Netfilter Core Team
    TCP cubic registered
    Initializing XFRM netlink socket
    NET: Registered protocol family 10
    ip6_tables: (C) 2000-2006 Netfilter Core Team
    IPv6 over IPv4 tunneling driver
    NET: Registered protocol family 17
    Bridge firewalling registered
    Ebtables v2.0 registered
    802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
    All bugs added by David S. Miller <davem@redhat.com>
    Using IPI Shortcut mode
    registered taskstats version 1
    ehci_hcd 0000:00:10.4: GetStatus port 3 status 001403 POWER sig=k CSC CONNECT
    hub 1-0:1.0: port 3: status 0501 change 0001
    uhci_hcd 0000:00:10.0: port 1 portsc 008a,00
    uhci_hcd 0000:00:10.0: port 2 portsc 008a,00
    uhci_hcd 0000:00:10.1: port 1 portsc 01aa,00
    uhci_hcd 0000:00:10.1: port 2 portsc 008a,00
    uhci_hcd 0000:00:10.2: port 1 portsc 008a,00
    uhci_hcd 0000:00:10.2: port 2 portsc 008a,00
    ata5.00: ATA-0: ELITE PRO CF CARD 16GB, Ver2.22K, max UDMA/100
    ata5.00: 31522176 sectors, multi 0: LBA
    ata5.00: configured for UDMA/100
    hub 1-0:1.0: state 7 ports 6 chg 0008 evt 0000
    hub 1-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
    ehci_hcd 0000:00:10.4: port 3 low speed --> companion
    ata5.00: configured for UDMA/100
    ata5: EH complete
    ehci_hcd 0000:00:10.4: GetStatus port 3 status 003402 POWER OWNER sig=k CSC
    hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
    uhci_hcd 0000:00:10.1: port 1 portsc 01a3,00
    hub 3-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
    ata2: SATA link down (SStatus 0 SControl 300)
    ata1: SATA link down (SStatus 0 SControl 300)
    hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
    usb 3-1: new low speed USB device using uhci_hcd and address 2
    usb 3-1: skipped 1 descriptor after interface
    usb 3-1: skipped 1 descriptor after interface
    usb 3-1: default language 0x0409
    usb 3-1: udev 2, busnum 3, minor = 257
    usb 3-1: New USB device found, idVendor=046d, idProduct=c30e
    usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
    usb 3-1: Product: HID compliant keyboard
    usb 3-1: Manufacturer: Logitech
    usb 3-1: uevent
    ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    usb 3-1: usb_probe_device
    usb 3-1: configuration #1 chosen from 1 choice
    ata4.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
    ata4.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    ata4.00: configured for UDMA/133
    ata3.00: ATA-7: WDC WD5000ABYS-01TNA0, 12.01C01, max UDMA/133
    ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
    usb 3-1: adding 3-1:1.0 (config #1, interface 0)
    usb 3-1:1.0: uevent
    usbhid 3-1:1.0: usb_probe_interface
    usbhid 3-1:1.0: usb_probe_interface - got id
    ata3.00: configured for UDMA/133
    scsi 2:0:0:0: Direct-Access ATA WDC WD5000ABYS-0 12.0 PQ: 0 ANSI: 5
    sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
    sd 2:0:0:0: [sda] Write Protect is off
    sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sda:
    sd 2:0:0:0: Attached scsi generic sg0 type 0
    scsi 3:0:0:0: Direct-Access ATA WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5
    sd 3:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
    sd 3:0:0:0: [sdb] Write Protect is off
    sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    sdb:
    sd 3:0:0:0: Attached scsi generic sg1 type 0
    scsi 4:0:0:0: Direct-Access ATA ELITE PRO CF CAR Ver2 PQ: 0 ANSI: 5
    sd 4:0:0:0: [sdc] 31522176 512-byte logical blocks: (16.1 GB/15.0 GiB)
    sd 4:0:0:0: [sdc] Write Protect is off
    sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
    sd 4:0:0:0: [sdc] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    sdc:
    sd 4:0:0:0: Attached scsi generic sg2 type 0
    sdc1
    sd 4:0:0:0: [sdc] Attached SCSI disk
    sda1
    sd 2:0:0:0: [sda] Attached SCSI disk
    input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:10.1/usb3/3-1/3-1:1.0/input/input3
    uhci_hcd 0000:00:10.1: reserve dev 2 ep81-INT, period 8, phase 4, 118 us
    generic-usb 0003:046D:C30E.0001: input,hidraw0: USB HID v1.10 Keyboard [Logitech HID compliant keyboard] on usb-0000:00:10.1-1/input0
    usb 3-1: adding 3-1:1.1 (config #1, interface 1)
    usb 3-1:1.1: uevent
    usbhid 3-1:1.1: usb_probe_interface
    usbhid 3-1:1.1: usb_probe_interface - got id
    input: Logitech HID compliant keyboard as /devices/pci0000:00/0000:00:10.1/usb3/3-1/3-1:1.1/input/input4
    uhci_hcd 0000:00:10.1: reserve dev 2 ep82-INT, period 8, phase 4, 118 us
    generic-usb 0003:046D:C30E.0002: input,hidraw1: USB HID v1.10 Device [Logitech HID compliant keyboard] on usb-0000:00:10.1-1/input1
    drivers/usb/core/inode.c: creating file '002'
    hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000
    hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0008
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
    usb usb2: suspend_rh (auto-stop)
    usb usb4: suspend_rh (auto-stop)
    sdb1
    sd 3:0:0:0: [sdb] Attached SCSI disk
    EXT3-fs: sdc1: couldn't mount because of unsupported optional features (240).
    EXT4-fs (sdc1): mounted filesystem with writeback data mode
    VFS: Mounted root (ext4 filesystem) readonly on device 8:33.
    Freeing unused kernel memory: 356k freed
    Write protecting the kernel text: 4912k
    Write protecting the kernel read-only data: 1272k
    stty used greatest stack depth: 6092 bytes left
    ln used greatest stack depth: 6088 bytes left
    udevadm used greatest stack depth: 6028 bytes left
    udev: starting version 146
    usb usb2: uevent
    usb 2-0:1.0: uevent
    usb usb3: uevent
    usb 3-0:1.0: uevent
    usb 3-1: uevent
    usb 3-1:1.0: uevent
    usb 3-1:1.1: uevent
    usb usb4: uevent
    usb 4-0:1.0: uevent
    usb usb1: uevent
    usb 1-0:1.0: uevent
    usb usb2: uevent
    usb usb3: uevent
    usb usb4: uevent
    usb usb1: uevent
    usb 3-1: uevent
    scsi_id used greatest stack depth: 6024 bytes left
    usb 3-1:1.0: uevent
    usb 3-1: uevent
    usb 3-1:1.1: uevent
    usb 3-1: uevent
    usb 3-1:1.1: uevent
    usb 3-1:1.0: uevent
    mount used greatest stack depth: 5544 bytes left
    hub 2-0:1.0: hub_suspend
    usb usb2: bus auto-suspend
    usb usb2: suspend_rh
    XFS mounting filesystem sda1
    Ending clean XFS mount for filesystem: sda1
    XFS mounting filesystem sdb1
    Ending clean XFS mount for filesystem: sdb1
    hub 4-0:1.0: hub_suspend
    usb usb4: bus auto-suspend
    usb usb4: suspend_rh
    hub 1-0:1.0: hub_suspend
    usb usb1: bus auto-suspend
    ehci_hcd 0000:00:10.4: suspend root hub
    usb 3-1: uhci_result_common: failed with status 440000
    uhci_hcd 0000:00:10.1: release dev 2 ep81-INT, period 8, phase 4, 118 us
    usb 3-1: uhci_result_common: failed with status 440000
    uhci_hcd 0000:00:10.1: release dev 2 ep82-INT, period 8, phase 4, 118 us
    uhci_hcd 0000:00:10.1: reserve dev 2 ep81-INT, period 8, phase 4, 118 us
    uhci_hcd 0000:00:10.1: reserve dev 2 ep82-INT, period 8, phase 4, 118 us
    usb 3-1: uhci_result_common: failed with status 440000
    uhci_hcd 0000:00:10.1: release dev 2 ep81-INT, period 8, phase 4, 118 us
    usb 3-1: uhci_result_common: failed with status 440000
    uhci_hcd 0000:00:10.1: release dev 2 ep82-INT, period 8, phase 4, 118 us
    uhci_hcd 0000:00:10.1: reserve dev 2 ep81-INT, period 8, phase 4, 118 us
    uhci_hcd 0000:00:10.1: reserve dev 2 ep82-INT, period 8, phase 4, 118 us
    usb 3-1: uhci_result_common: failed with status 440000
    uhci_hcd 0000:00:10.1: release dev 2 ep81-INT, period 8, phase 4, 118 us
    usb 3-1: uhci_result_common: failed with status 440000
    uhci_hcd 0000:00:10.1: release dev 2 ep82-INT, period 8, phase 4, 118 us
    uhci_hcd 0000:00:10.1: reserve dev 2 ep81-INT, period 8, phase 4, 118 us
    uhci_hcd 0000:00:10.1: reserve dev 2 ep82-INT, period 8, phase 4, 118 us
    hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002
    uhci_hcd 0000:00:10.1: port 1 portsc 018a,00
    hub 3-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
    usb 3-1: USB disconnect, address 2
    usb 3-1: unregistering device
    usb 3-1: usb_disable_device nuking all URBs
    uhci_hcd 0000:00:10.1: shutdown urb f72d1180 ep1in-intr
    uhci_hcd 0000:00:10.1: release dev 2 ep81-INT, period 8, phase 4, 118 us
    uhci_hcd 0000:00:10.1: shutdown urb f6816c80 ep2in-intr
    uhci_hcd 0000:00:10.1: release dev 2 ep82-INT, period 8, phase 4, 118 us
    usb 3-1: unregistering interface 3-1:1.0
    usb 3-1:1.0: uevent
    usb 3-1: unregistering interface 3-1:1.1
    usb 3-1:1.1: uevent
    usb 3-1: uevent
    hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x300
    usb usb3: suspend_rh (auto-stop)
    Velocity is AUTO mode
    eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
    device eth0 entered promiscuous mode
    device eth1 entered promiscuous mode
    br0: port 2(eth1) entering forwarding state
    br0: port 1(eth0) entering forwarding state
    hub 3-0:1.0: hub_suspend
    usb usb3: bus auto-suspend
    usb usb3: suspend_rh
    eth1: Link auto-negotiation speed 1000M bps full duplex
    svc: failed to register lockdv1 RPC service (errno 97).
    NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
    NFSD: starting 90-second grace period
    rpc.nfsd used greatest stack depth: 5160 bytes left
    eth1: no IPv6 routers present
    br0: no IPv6 routers present
    eth0: no IPv6 routers present
    wget used greatest stack depth: 4840 bytes left
    [unhandled content-type:application/pgp-signature]
    \
     
     \ /
      Last update: 2010-04-19 00:41    [W:0.086 / U:60.320 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site