lkml.org 
[lkml]   [2010]   [Feb]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    Date
    From
    SubjectRe: UIO support for >32-bit physical addresses on 32-bit platforms
    On Tue, Feb 23, 2010 at 04:52:56PM -0600, Kumar Gala wrote:
    >
    > On Feb 23, 2010, at 1:49 PM, Hans J. Koch wrote:
    >
    > > On Tue, Feb 23, 2010 at 07:01:41AM -0800, Greg KH wrote:
    > >> On Tue, Feb 23, 2010 at 08:54:16AM -0600, Kumar Gala wrote:
    > >>> Hans, Greg,
    > >>>
    > >>> We are looking at using UIO for some driver work and noticed it
    > >>> assumes the address for MMIO regions is an 'unsigned long'. This is a
    > >>> problem for the platforms we have in which we support a 36-bit
    > >>> physical address in a 32-bit machine.
    > >>>
    > >>> Should we just change addr/size in struct uio_mem to u64 always?
    > >
    > > No, if I didn't miss something important, it's not feasible IMHO.
    > >
    > >>> At
    > >>> first I was thinking phys_addr_t but realized the addr could be PHYS,
    > >>> LOGICAL, or VIRTUAL.
    > >>
    > >> I think that would work out fine, Hans, any ideas if this would cause
    > >> any problems with existing code or not?
    > >
    > > It won't work. This is not a UIO problem. UIO just passes addr to other
    > > system functions, and all of them use "unsigned long" for these addresses.
    > > You'd have to change the whole memory management code.
    > >
    > > Note that members vm_start and vm_end in struct vm_area_struct are
    > > also unsigned long. Having an u64 in the UIO core doesn't help at all.
    >
    > This already works for mmap since we pass down a PFN and not an address to remap_pfn_range. While we can handle any physical address size we can handle one up to 44 bits on most architectures which is well beyond the 36-bit physical address case I'm dealing with on PPC.
    >

    Sure, there are always ways to handle physical addresses up to the buswidth
    of the arch. But above the "natural" size (32 bits on 32-bit archs), it
    becomes a bit clumsy. UIO has a documented interface to userspace. The user
    is supposed to use the traditional mmap() call. mmap() returns void*, which
    is also 32 bits on 32-bit archs.

    Because of this, UIO already needs a 32-bit address. It might be possible to
    map your I/O memory from above 4G down into the 32-bit space and then use
    this address, probably not with UIO_MEM_PHYS but with UIO_MEM_VIRTUAL.
    I understand PPC (is that an E500?) has some special features for doing
    these kind of shifts in hardware. But I'm not really a PPC expert, I'll
    ask a friend of mine.

    > > Memory above the 4G border can only be accessed through himem mechanisms
    > > or be mapped to an address below that border in lowlevel arch code.
    > >
    > > In most cases, I'd say it's bad board design to have memory-mapped hardware
    > > above the 4G border on a 32-bit machine.
    >
    > While I might agree with you its a reality on a number of embedded processors and I know three different PowerPC based embedded families that have 36-bit physical addressing to allow for >4G of DDR and thus IO ends up being above the 4G physical boundary and we already support these in the kernel.

    Well, UIO is (up to now) completely independent of the architecture. If you've
    got a good idea how to implement such mappings, feel free to come up with your
    suggestions/patches. Just changing struct uio_mem.addr to u64 is certainly not
    enough.

    I'll give it some thoughts myself, and will discuss the problem with friends,
    maybe there's a nice solution. Help from your side is much appreciated.

    Thanks,
    Hans

    >
    > - k


    \
     
     \ /
      Last update: 2010-02-24 00:41    [W:3.023 / U:0.008 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site