lkml.org 
[lkml]   [2010]   [Nov]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH 1/1] ARM Orion: added Buffalo LS-CHL support
Hi Ashley,

On Sun, Nov 21, 2010 at 11:05:10PM -0000, Ash Hughes wrote:
> Adds support for Buffalo Linkstation Live v3 (LS-CHL) NAS drives.
> Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
>
> ---
>
>
> diff -uprN linux-2.6-vanilla//arch/arm/mach-orion5x/Kconfig linux-2.6/arch/arm/mach-orion5x/Kconfig
> --- linux-2.6-vanilla//arch/arm/mach-orion5x/Kconfig 2010-11-14 10:58:39.000000000 +0000
> +++ linux-2.6/arch/arm/mach-orion5x/Kconfig 2010-11-14 11:02:42.874582000 +0000
> @@ -51,6 +51,13 @@ config MACH_LINKSTATION_PRO
> Buffalo Linkstation Pro/Live platform. Both v1 and
> v2 devices are supported.
>
> +config MACH_LINKSTATION_LSCHL
> + bool "Buffalo Linkstation Live v3 (LS-CHL)"
> + select I2C_BOARDINFO
> + help
> + Say 'Y' here if you want your kernel to support the
> + Buffalo Linkstation Live v3 (LS-CHL) platform.
> +
> config MACH_LINKSTATION_MINI
> bool "Buffalo Linkstation Mini"
> select I2C_BOARDINFO
> diff -uprN linux-2.6-vanilla//arch/arm/mach-orion5x/ls-chl-setup.c linux-2.6/arch/arm/mach-orion5x/ls-chl-setup.c
> --- linux-2.6-vanilla//arch/arm/mach-orion5x/ls-chl-setup.c 1970-01-01 01:00:00.000000000 +0100
> +++ linux-2.6/arch/arm/mach-orion5x/ls-chl-setup.c 2010-11-21 15:33:43.910827481 +0000
> @@ -0,0 +1,329 @@
> +/*
> + * arch/arm/mach-orion5x/ls-chl-setup.c
> + *
> + * Maintainer: Ash Hughes <ashley.hughes@blueyonder.co.uk>
> + *
> + * This file is licensed under the terms of the GNU General Public
> + * License version 2. This program is licensed "as is" without any
> + * warranty of any kind, whether express or implied.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/platform_device.h>
> +#include <linux/mtd/physmap.h>
> +#include <linux/mv643xx_eth.h>
> +#include <linux/leds.h>
> +#include <linux/gpio_keys.h>
> +#include <linux/gpio-fan.h>
> +#include <linux/input.h>
> +#include <linux/i2c.h>
> +#include <linux/ata_platform.h>
> +#include <linux/gpio.h>
> +#include <asm/mach-types.h>
> +#include <asm/mach/arch.h>
> +#include <asm/system.h>
> +#include <mach/orion5x.h>
> +#include "common.h"
> +#include "mpp.h"
> +
> +/*****************************************************************************
> + * Linkstation LS-CHL Info
> + ****************************************************************************/
> +
> +/*
> + * 256K NOR flash Device bus boot chip select
> + */
> +
> +#define LSCHL_NOR_BOOT_BASE 0xf4000000
> +#define LSCHL_NOR_BOOT_SIZE SZ_256K
> +
> +/*****************************************************************************
> + * 256KB NOR Flash on BOOT Device
> + ****************************************************************************/
> +
> +static struct physmap_flash_data lschl_nor_flash_data = {
> + .width = 1,
> +};
> +
> +static struct resource lschl_nor_flash_resource = {
> + .flags = IORESOURCE_MEM,
> + .start = LSCHL_NOR_BOOT_BASE,
> + .end = LSCHL_NOR_BOOT_BASE + LSCHL_NOR_BOOT_SIZE - 1,
> +};
> +
> +static struct platform_device lschl_nor_flash = {
> + .name = "physmap-flash",
> + .id = 0,
> + .dev = {
> + .platform_data = &lschl_nor_flash_data,
> + },
> + .num_resources = 1,
> + .resource = &lschl_nor_flash_resource,
> +};
> +
> +/*****************************************************************************
> + * Ethernet
> + ****************************************************************************/
> +
> +static struct mv643xx_eth_platform_data lschl_eth_data = {
> + .phy_addr = MV643XX_ETH_PHY_ADDR(8),
> +};
> +
> +/*****************************************************************************
> + * RTC 5C372a on I2C bus
> + ****************************************************************************/
> +
> +static struct i2c_board_info __initdata lschl_i2c_rtc = {
> + I2C_BOARD_INFO("rs5c372a", 0x32),
> +};
> +
> +/*****************************************************************************
> + * LEDs attached to GPIO
> + ****************************************************************************/
> +
> +#define LSCHL_GPIO_LED_ALARM 2
> +#define LSCHL_GPIO_LED_INFO 3
> +#define LSCHL_GPIO_LED_FUNC 17
> +#define LSCHL_GPIO_LED_PWR 0
> +
> +static struct gpio_led lschl_led_pins[] = {
> + {
> + .name = "alarm:red",
> + .gpio = LSCHL_GPIO_LED_ALARM,
> + .active_low = 1,
> + }, {
> + .name = "info:amber",
> + .gpio = LSCHL_GPIO_LED_INFO,
> + .active_low = 1,
> + }, {
> + .name = "func:blue:top",
> + .gpio = LSCHL_GPIO_LED_FUNC,
> + .active_low = 1,
> + }, {
> + .name = "power:blue:bottom",
> + .gpio = LSCHL_GPIO_LED_PWR,
> + },
> +};
You should use tabs instead of spaces for indentation.
The same comment apply to some other places in this file.

> +
> +static struct gpio_led_platform_data lschl_led_data = {
> + .leds = lschl_led_pins,
> + .num_leds = ARRAY_SIZE(lschl_led_pins),
> +};
> +
> +static struct platform_device lschl_leds = {
> + .name = "leds-gpio",
> + .id = -1,
> + .dev = {
> + .platform_data = &lschl_led_data,
> + },
> +};
> +
> +/*****************************************************************************
> + * SATA
> + ****************************************************************************/
> +static struct mv_sata_platform_data lschl_sata_data = {
> + .n_ports = 2,
> +};
> +
> +/*****************************************************************************
> + * LS-CHL specific power off method: reboot
> + ****************************************************************************/
> +/*
> + * On the LS-CHL, the shutdown process is following:
> + * - Userland monitors key events until the power switch goes to off position
> + * - The board reboots
> + * - U-boot starts and goes into an idle mode waiting for the user
> + * to move the switch to ON position
> + *
> + */
> +
> +static void lschl_power_off(void)
> +{
> + arm_machine_restart('h', NULL);
> +}

Maybe that userland could just call "reboot" when a switch "power-off"
event happen ?
Is it possible to power-off the Linkstation device ?

> +
> +/*****************************************************************************
> + * General Setup
> + ****************************************************************************/
> +#define LSCHL_GPIO_USB_POWER 9
> +#define LSCHL_GPIO_AUTO_POWER 17
> +#define LSCHL_GPIO_POWER 18
> +
> +/****************************************************************************
> + * GPIO Attached Keys
> + ****************************************************************************/
> +#define LSCHL_GPIO_KEY_FUNC 15
> +#define LSCHL_GPIO_KEY_POWER 8
> +#define LSCHL_GPIO_KEY_AUTOPOWER 10
> +#define LSCHL_SW_POWER 0x00
> +#define LSCHL_SW_AUTOPOWER 0x01
> +#define LSCHL_SW_FUNC 0x02
> +
> +static struct gpio_keys_button lschl_buttons[] = {
> + {
> + .type = EV_SW,
> + .code = LSCHL_SW_POWER,
> + .gpio = LSCHL_GPIO_KEY_POWER,
> + .desc = "Power-on Switch",
> + .active_low = 1,
> + }, {
> + .type = EV_SW,
> + .code = LSCHL_SW_AUTOPOWER,
> + .gpio = LSCHL_GPIO_KEY_AUTOPOWER,
> + .desc = "Power-auto Switch",
> + .active_low = 1,
> + }, {
> + .type = EV_SW,
> + .code = LSCHL_SW_FUNC,
> + .gpio = LSCHL_GPIO_KEY_FUNC,
> + .desc = "Function Switch",
> + .active_low = 1,
> + },
> +};
> +
> +static struct gpio_keys_platform_data lschl_button_data = {
> + .buttons = lschl_buttons,
> + .nbuttons = ARRAY_SIZE(lschl_buttons),
> +};
> +
> +static struct platform_device lschl_button_device = {
> + .name = "gpio-keys",
> + .id = -1,
> + .num_resources = 0,
> + .dev = {
> + .platform_data = &lschl_button_data,
> + },
> +};
> +
> +#define LSCHL_GPIO_HDD_POWER 1
> +
> +/****************************************************************************
> + * GPIO Fan
> + ****************************************************************************/
> +
> +#define LSCHL_GPIO_FAN_LOW 16
> +#define LSCHL_GPIO_FAN_HIGH 14
> +#define LSCHL_GPIO_FAN_LOCK 6
> +
> +static struct gpio_fan_alarm lschl_alarm = {
> + .gpio = LSCHL_GPIO_FAN_LOCK,
> + .active_low = 0,

You don't need to set active_low to 0.

> +};
> +
> +static struct gpio_fan_speed lschl_speeds[] = {
> + {
> + .rpm = 0,
> + .ctrl_val = 3,
> + }, {
> + .rpm = 1,
> + .ctrl_val = 2,
> + }, {
> + .rpm = 2,
> + .ctrl_val = 1,
> + }, {
> + .rpm = 3,
> + .ctrl_val = 0,
> + },
> +};

The rpm values are rather surprising. Can you either measure or estimate
the fan speed ?

> +
> +static int lschl_gpio_list[] = {
> + LSCHL_GPIO_FAN_HIGH, LSCHL_GPIO_FAN_LOW,
> +};
> +
> +static struct gpio_fan_platform_data lschl_fan_data = {
> + .num_ctrl = 2,
> + .ctrl = lschl_gpio_list,
> + .alarm = &lschl_alarm,
> + .num_speed = 4,
> + .speed = lschl_speeds,
> +};
> +
> +static struct platform_device lschl_fan_device = {
> + .name = "gpio-fan",
> + .id = -1,
> + .num_resources = 0,
> + .dev = {
> + .platform_data = &lschl_fan_data,
> + },
> +};
> +
> +/****************************************************************************
> + * GPIO Data
> + ****************************************************************************/
> +
> +static struct orion5x_mpp_mode lschl_mpp_modes[] __initdata = {
> + { 0, MPP_GPIO }, /* LED POWER */
> + { 1, MPP_GPIO }, /* HDD POWER */
> + { 2, MPP_GPIO }, /* LED ALARM */
> + { 3, MPP_GPIO }, /* LED INFO */
> + { 4, MPP_UNUSED },
> + { 5, MPP_UNUSED },
> + { 6, MPP_GPIO }, /* FAN LOCK */
> + { 7, MPP_GPIO }, /* SW INIT */
> + { 8, MPP_GPIO }, /* SW POWER */
> + { 9, MPP_GPIO }, /* USB POWER */
> + { 10, MPP_GPIO }, /* SW AUTO POWER */
> + { 11, MPP_UNUSED },
> + { 12, MPP_UNUSED },
> + { 13, MPP_UNUSED },
> + { 14, MPP_GPIO }, /* FAN HIGH */
> + { 15, MPP_GPIO }, /* SW FUNC */
> + { 16, MPP_GPIO }, /* FAN LOW */
> + { 17, MPP_GPIO }, /* LED FUNC */
> + { 18, MPP_UNUSED },
> + { 19, MPP_UNUSED },
> + { -1 },
> +};
> +
> +static void __init lschl_init(void)
> +{
> + /*
> + * Setup basic Orion functions. Needs to be called early.
> + */
> + orion5x_init();
> +
> + orion5x_mpp_conf(lschl_mpp_modes);
> +
> + /*
> + * Configure peripherals.
> + */
> + orion5x_ehci0_init();
> + orion5x_ehci1_init();
> + orion5x_eth_init(&lschl_eth_data);
> + orion5x_i2c_init();
> + orion5x_sata_init(&lschl_sata_data);
> + orion5x_uart0_init();
> + orion5x_xor_init();
> +
> + orion5x_setup_dev_boot_win(LSCHL_NOR_BOOT_BASE,
> + LSCHL_NOR_BOOT_SIZE);
> + platform_device_register(&lschl_nor_flash);
> +
> + platform_device_register(&lschl_leds);
> +
> + platform_device_register(&lschl_button_device);
> +
> + platform_device_register(&lschl_fan_device);
> +
> + i2c_register_board_info(0, &lschl_i2c_rtc, 1);
> +
> + /* usb power on */
> + gpio_set_value(LSCHL_GPIO_USB_POWER, 1);
> +
> + /* register power-off method */
> + pm_power_off = lschl_power_off;
> +
> + pr_info("%s: finished\n", __func__);
> +}
> +
> +MACHINE_START(LINKSTATION_LSCHL, "Buffalo Linkstation LiveV3 (LS-CHL)")
> + /* Maintainer: Ash Hughes <ashley.hughes@blueyonder.co.uk> */
> + .boot_params = 0x00000100,
> + .init_machine = lschl_init,
> + .map_io = orion5x_map_io,
> + .init_irq = orion5x_init_irq,
> + .timer = &orion5x_timer,
> + .fixup = tag_fixup_mem32,
> +MACHINE_END
> +
> diff -uprN linux-2.6-vanilla//arch/arm/mach-orion5x/Makefile linux-2.6/arch/arm/mach-orion5x/Makefile
> --- linux-2.6-vanilla//arch/arm/mach-orion5x/Makefile 2010-11-14 10:58:39.000000000 +0000
> +++ linux-2.6/arch/arm/mach-orion5x/Makefile 2010-11-14 11:03:34.444582001 +0000
> @@ -21,3 +21,4 @@ obj-$(CONFIG_MACH_WNR854T) += wnr854t-se
> obj-$(CONFIG_MACH_RD88F5181L_GE) += rd88f5181l-ge-setup.o
> obj-$(CONFIG_MACH_RD88F5181L_FXO) += rd88f5181l-fxo-setup.o
> obj-$(CONFIG_MACH_RD88F6183AP_GE) += rd88f6183ap-ge-setup.o
> +obj-$(CONFIG_MACH_LINKSTATION_LSCHL) += ls-chl-setup.o

You should replace spaces with tab here too.

Simon
[unhandled content-type:application/pgp-signature]
\
 
 \ /
  Last update: 2010-11-24 02:07    [W:0.546 / U:0.732 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site