lkml.org 
[lkml]   [2010]   [Nov]   [20]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    Date
    From
    Subject[patch 2/2] mm: add node hotplug emulation

    Add an interface to allow new nodes to be added when performing memory
    hot-add. This provides a convenient interface to test memory hotplug
    notifier callbacks and surrounding hotplug code when new nodes are
    onlined without actually having a machine with such hotpluggable SRAT
    entries.

    This adds a new interface at /sys/devices/system/memory/add_node that
    behaves in a similar way to the memory hot-add "probe" interface. Its
    format is size@start, where "size" is the size of the new node to be
    added and "start" is the physical address of the new memory.

    The new node id is a currently offline, but possible, node. The bit must
    be set in node_possible_map so that nr_node_ids is sized appropriately.

    For emulation on x86, for example, it would be possible to set aside
    memory for hotplugged nodes (say, anything above 2G) and to add an
    additional three nodes as being possible on boot with

    mem=2G numa=possible=3

    and then creating a new 128M node at runtime:

    # echo 128M@0x80000000 > /sys/devices/system/memory/add_node
    On node 1 totalpages: 0
    init_memory_mapping: 0000000080000000-0000000088000000
    0080000000 - 0088000000 page 2M

    Once the new node has been added, its memory can be onlined. If this
    memory represents memory section 16, for example:

    # echo online > /sys/devices/system/memory/memory16/state
    Built 2 zonelists in Node order, mobility grouping on. Total pages: 514846
    Policy zone: Normal

    [ The memory section(s) mapped to a particular node are visible via
    /sys/devices/system/node/node1, in this example. ]

    The new node is now hotplugged and ready for testing.

    Signed-off-by: David Rientjes <rientjes@google.com>
    ---
    Documentation/memory-hotplug.txt | 24 ++++++++++++++++++++++++
    drivers/base/memory.c | 36 +++++++++++++++++++++++++++++++++++-
    2 files changed, 59 insertions(+), 1 deletions(-)

    diff --git a/Documentation/memory-hotplug.txt b/Documentation/memory-hotplug.txt
    --- a/Documentation/memory-hotplug.txt
    +++ b/Documentation/memory-hotplug.txt
    @@ -18,6 +18,7 @@ be changed often.
    4. Physical memory hot-add phase
    4.1 Hardware(Firmware) Support
    4.2 Notify memory hot-add event by hand
    + 4.3 Node hotplug emulation
    5. Logical Memory hot-add phase
    5.1. State of memory
    5.2. How to online memory
    @@ -215,6 +216,29 @@ current implementation). You'll have to online memory by yourself.
    Please see "How to online memory" in this text.


    +4.3 Node hotplug emulation
    +------------
    +It is possible to test node hotplug by assigning the newly added memory to a
    +new node id when using a different interface with a similar behavior to
    +"probe" described in section 4.2. If a node id is possible (there are bits
    +in /sys/devices/system/memory/possible that are not online), then it may be
    +used to emulate a newly added node as the result of memory hotplug by using
    +the "add_node" interface.
    +
    +The add_node interface is located at
    +/sys/devices/system/memory/add_node
    +
    +You can create a new node of a specified size starting at the physical
    +address of new memory by
    +
    +% echo size@start_address_of_new_memory > /sys/devices/system/memory/add_node
    +
    +Where "size" can be represented in megabytes or gigabytes (for example,
    +"128M" or "1G"). The minumum size is that of a memory section.
    +
    +Once the new node has been added, it is possible to online the memory by
    +toggling the "state" of its memory section(s) as described in section 5.1.
    +

    ------------------------------
    5. Logical Memory hot-add phase
    diff --git a/drivers/base/memory.c b/drivers/base/memory.c
    --- a/drivers/base/memory.c
    +++ b/drivers/base/memory.c
    @@ -353,10 +353,44 @@ memory_probe_store(struct class *class, struct class_attribute *attr,
    }
    static CLASS_ATTR(probe, S_IWUSR, NULL, memory_probe_store);

    +static ssize_t
    +memory_add_node_store(struct class *class, struct class_attribute *attr,
    + const char *buf, size_t count)
    +{
    + nodemask_t mask;
    + u64 start, size;
    + char *p;
    + int nid;
    + int ret;
    +
    + size = memparse(buf, &p);
    + if (size < (PAGES_PER_SECTION << PAGE_SHIFT))
    + return -EINVAL;
    + if (*p != '@')
    + return -EINVAL;
    +
    + start = simple_strtoull(p + 1, NULL, 0);
    +
    + nodes_andnot(mask, node_possible_map, node_online_map);
    + nid = first_node(mask);
    + if (nid == MAX_NUMNODES)
    + return -EINVAL;
    +
    + ret = add_memory(nid, start, size);
    + return ret ? ret : count;
    +}
    +static CLASS_ATTR(add_node, S_IWUSR, NULL, memory_add_node_store);
    +
    static int memory_probe_init(void)
    {
    - return sysfs_create_file(&memory_sysdev_class.kset.kobj,
    + int err;
    +
    + err = sysfs_create_file(&memory_sysdev_class.kset.kobj,
    &class_attr_probe.attr);
    + if (err)
    + return err;
    + return sysfs_create_file(&memory_sysdev_class.kset.kobj,
    + &class_attr_add_node.attr);
    }
    #else
    static inline int memory_probe_init(void)

    \
     
     \ /
      Last update: 2010-11-21 03:31    [W:0.040 / U:31.336 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site