lkml.org 
[lkml]   [2010]   [Nov]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [ANNOUNCE v2] ktest.pl: Easy and flexible testing script for Linux Kernel Developers (now with config bisect)
FromSteven Rostedt <>
DateThu, 18 Nov 2010 09:08:37 -0500
Question:

Has anyone tried this out? Does anyone feel that I should get this ready
to be included in 2.6.38 tools directory?

Just want to know if I should go ahead and prepare it, or if it will
just be a waste of my time.

Thanks,

-- Steve


On Mon, 2010-11-08 at 18:45 -0500, Steven Rostedt wrote:
> I previously posted the announcement about ktest (and shamelessly
> promoted it at both Kernel Summit and Linux Plumbers), but I just
> updated it with a new feature.
>
> TEST_TYPE = config_bisect
>
> (See http://marc.info/?l=linux-kernel&m=128829496215347 for original
> post)
>
> With the new config_bisect, the config is tested in halves. To handle
> strange dependencies, the following is done.
>
> First the "bad-config" needs to be prepared for the current working git
> tree. As with all other tests, a "min-config" may be specified and that
> will be override any config settings in the "bad-config". Since this may
> produce new settings to be set (or removed) some preparation needs to be
> done. This is done automatically with ktest:
>
> 1) overrides all configs with what is in the MIN_CONFIG or ADD_CONFIG
> settings.
>
> 2) Runs the result through a make oldconfig to see if what may have been
> added or removed (it reports these).
>
> 3) creates what is about to be tested and again runs the make oldconfig
> to see if anything else might have been removed by dependencies.
>
> All of the above changes are reported by the tool.
>
>
> Finally, it gets into the bisect. It starts with a list of configs to
> test. It cuts it in half, and then creates a .config file, and runs that
> through oldconfig. If none of the configs in the list are enabled
> (because they all depend on configs in the other half) then the second
> half of the list is tried. If there's still no configs set, there must
> be a circular dependency and the test fails here (but this should never
> happen).
>
> It compiles, and performs the type of test specified by the
> CONFIG_BISECT_TYPE option (build, boot or test). If it passes, then all
> the configs that were enabled in the .config are removed from the
> configs to test and added to the good configs to always enable. This
> allows for configs in the other half to be enabled if they depended on
> these configs.
>
> If the test fails, then we have a new subset of configs that is known to
> cause the failure. Any config that was not set in the .config for this
> run is removed from the test and will not be enabled again.
>
> This iterates until we have one config left and that config will be
> reported.
>
> Because of dependencies and selects, the config reported may not be the
> only config to cause the error. If you find that you can still produce
> an error after disabling the config it reports, then simply disable it
> and run the bisect again. Most likely it will turn up the problem. I may
> automate this part in the future.
>
> Anyway, you can download the latest ktest from:
>
> git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/ktest.git
>
> I need to write up a man page and perhaps more documentation. The
> sample.conf that comes in that repo has loads of information on how to
> do the tests.
>
>
> Have fun!
>
> -- Steve
>




\
 
 \ /
  Last update: 2010-11-18 15:11    [from the cache]
©2003-2010