lkml.org 
[lkml]   [2010]   [Nov]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
Subject[PATCH 05/07] ARM: Use shared GIC entry macros on UX500
From: Magnus Damm <damm@opensource.se>

Use the GIC demux code in asm/hardware/entry-macro-gic.S
on the UX500 subarchitecture.

Signed-off-by: Magnus Damm <damm@opensource.se>
---

arch/arm/mach-ux500/include/mach/entry-macro.S | 67 ------------------------
1 file changed, 1 insertion(+), 66 deletions(-)

--- 0001/arch/arm/mach-ux500/include/mach/entry-macro.S
+++ work/arch/arm/mach-ux500/include/mach/entry-macro.S 2010-11-12 16:02:32.000000000 +0900
@@ -11,7 +11,7 @@
* warranty of any kind, whether express or implied.
*/
#include <mach/hardware.h>
-#include <asm/hardware/gic.h>
+#include <asm/hardware/entry-macro-gic.S>

.macro disable_fiq
.endm
@@ -22,68 +22,3 @@

.macro arch_ret_to_user, tmp1, tmp2
.endm
-
- /*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec. To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-28 are reserved
- * 29-31 are local. We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * For now, we ignore all local interrupts so only return an
- * interrupt if it's between 30 and 1020. The test_for_ipi
- * routine below will pick up on IPIs.
- *
- * A simple read from the controller will tell us the number
- * of the highest priority enabled interrupt. We then just
- * need to check whether it is in the valid range for an
- * IRQ (30-1020 inclusive).
- */
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
-
- /* bits 12-10 = src CPU, 9-0 = int # */
- ldr \irqstat, [\base, #GIC_CPU_INTACK]
-
- ldr \tmp, =1021
-
- bic \irqnr, \irqstat, #0x1c00
-
- cmp \irqnr, #29
- cmpcc \irqnr, \irqnr
- cmpne \irqnr, \tmp
- cmpcs \irqnr, \irqnr
-
- .endm
-
- /* We assume that irqstat (the raw value of the IRQ
- * acknowledge register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of
- * interrupt on the controller, since this requires the
- * original irqstat value which we won't easily be able
- * to recreate later.
- */
-
- .macro test_for_ipi, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- cmp \irqnr, #16
- strcc \irqstat, [\base, #GIC_CPU_EOI]
- cmpcs \irqnr, \irqnr
- .endm
-
- /* As above, this assumes that irqstat and base
- * are preserved..
- */
-
- .macro test_for_ltirq, irqnr, irqstat, base, tmp
- bic \irqnr, \irqstat, #0x1c00
- mov \tmp, #0
- cmp \irqnr, #29
- moveq \tmp, #1
- streq \irqstat, [\base, #GIC_CPU_EOI]
- cmp \tmp, #0
- .endm

\
 
 \ /
  Last update: 2010-11-12 09:21    [W:0.056 / U:0.224 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site