lkml.org 
[lkml]   [2010]   [Oct]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 43/49] Alchemy: Add UART PM methods.
Date
From: Manuel Lauss <manuel.lauss@googlemail.com>

Custom UART PM hook for Alchemy chips: do standard UART pm and
additionally en/disable uart block clocks as needed.
This allows to get rid of a debug port PM hack in the Alchemy pm code.

Tested on Db1200.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
---
arch/mips/alchemy/common/platform.c | 28 ++++++++++++++++++++++++++++
arch/mips/alchemy/common/power.c | 35 -----------------------------------
2 files changed, 28 insertions(+), 35 deletions(-)

diff --git a/arch/mips/alchemy/common/platform.c b/arch/mips/alchemy/common/platform.c
index 1dc55ee..3691630 100644
--- a/arch/mips/alchemy/common/platform.c
+++ b/arch/mips/alchemy/common/platform.c
@@ -24,6 +24,33 @@

#include <prom.h>

+static void alchemy_8250_pm(struct uart_port *port, unsigned int state,
+ unsigned int old_state)
+{
+ switch (state) {
+ case 0:
+ if ((__raw_readl(port->membase + UART_MOD_CNTRL) & 3) != 3) {
+ /* power-on sequence as suggested in the databooks */
+ __raw_writel(0, port->membase + UART_MOD_CNTRL);
+ wmb();
+ __raw_writel(1, port->membase + UART_MOD_CNTRL);
+ wmb();
+ }
+ __raw_writel(3, port->membase + UART_MOD_CNTRL); /* full on */
+ wmb();
+ serial8250_do_pm(port, state, old_state);
+ break;
+ case 3: /* power off */
+ serial8250_do_pm(port, state, old_state);
+ __raw_writel(0, port->membase + UART_MOD_CNTRL);
+ wmb();
+ break;
+ default:
+ serial8250_do_pm(port, state, old_state);
+ break;
+ }
+}
+
#define PORT(_base, _irq) \
{ \
.mapbase = _base, \
@@ -33,6 +60,7 @@
.flags = UPF_SKIP_TEST | UPF_IOREMAP | \
UPF_FIXED_TYPE, \
.type = PORT_16550A, \
+ .pm = alchemy_8250_pm, \
}

static struct plat_serial8250_port au1x00_uart_data[] = {
diff --git a/arch/mips/alchemy/common/power.c b/arch/mips/alchemy/common/power.c
index 5ef06a1..e5916a5 100644
--- a/arch/mips/alchemy/common/power.c
+++ b/arch/mips/alchemy/common/power.c
@@ -49,11 +49,6 @@
* We only have to save/restore registers that aren't otherwise
* done as part of a driver pm_* function.
*/
-static unsigned int sleep_uart0_inten;
-static unsigned int sleep_uart0_fifoctl;
-static unsigned int sleep_uart0_linectl;
-static unsigned int sleep_uart0_clkdiv;
-static unsigned int sleep_uart0_enable;
static unsigned int sleep_usb[2];
static unsigned int sleep_sys_clocks[5];
static unsigned int sleep_sys_pinfunc;
@@ -62,22 +57,6 @@ static unsigned int sleep_static_memctlr[4][3];

static void save_core_regs(void)
{
- extern void save_au1xxx_intctl(void);
- extern void pm_eth0_shutdown(void);
-
- /*
- * Do the serial ports.....these really should be a pm_*
- * registered function by the driver......but of course the
- * standard serial driver doesn't understand our Au1xxx
- * unique registers.
- */
- sleep_uart0_inten = au_readl(UART0_ADDR + UART_IER);
- sleep_uart0_fifoctl = au_readl(UART0_ADDR + UART_FCR);
- sleep_uart0_linectl = au_readl(UART0_ADDR + UART_LCR);
- sleep_uart0_clkdiv = au_readl(UART0_ADDR + UART_CLK);
- sleep_uart0_enable = au_readl(UART0_ADDR + UART_MOD_CNTRL);
- au_sync();
-
#ifndef CONFIG_SOC_AU1200
/* Shutdown USB host/device. */
sleep_usb[0] = au_readl(USB_HOST_CONFIG);
@@ -175,20 +154,6 @@ static void restore_core_regs(void)
au_writel(sleep_static_memctlr[3][0], MEM_STCFG3);
au_writel(sleep_static_memctlr[3][1], MEM_STTIME3);
au_writel(sleep_static_memctlr[3][2], MEM_STADDR3);
-
- /*
- * Enable the UART if it was enabled before sleep.
- * I guess I should define module control bits........
- */
- if (sleep_uart0_enable & 0x02) {
- au_writel(0, UART0_ADDR + UART_MOD_CNTRL); au_sync();
- au_writel(1, UART0_ADDR + UART_MOD_CNTRL); au_sync();
- au_writel(3, UART0_ADDR + UART_MOD_CNTRL); au_sync();
- au_writel(sleep_uart0_inten, UART0_ADDR + UART_IER); au_sync();
- au_writel(sleep_uart0_fifoctl, UART0_ADDR + UART_FCR); au_sync();
- au_writel(sleep_uart0_linectl, UART0_ADDR + UART_LCR); au_sync();
- au_writel(sleep_uart0_clkdiv, UART0_ADDR + UART_CLK); au_sync();
- }
}

void au_sleep(void)
--
1.7.2


\
 
 \ /
  Last update: 2010-10-22 20:27    [W:0.269 / U:0.016 seconds]
©2003-2017 Jasper Spaans. hosted at Digital OceanAdvertise on this site