lkml.org 
[lkml]   [2010]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[patch 2/2] x86, apic: use logical flat for systems with <= 8 logical cpus
We can use logical flat mode if there are <= 8 logical cpu's (irrespective
of physical apic id values). This will enable simplified and efficient IPI
and device interrupt routing on such platforms.

This has been tested to work on both Intel and AMD platforms. Exceptions
like IBM summit platform which can't use logical flat mode are addressed
by using OEM platform checks.

Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Chris McDermott <lcm@linux.vnet.ibm.com>
---
arch/x86/kernel/apic/apic.c | 15 +--------------
arch/x86/kernel/apic/probe_64.c | 8 +++-----
2 files changed, 4 insertions(+), 19 deletions(-)

Index: tip/arch/x86/kernel/apic/apic.c
===================================================================
--- tip.orig/arch/x86/kernel/apic/apic.c
+++ tip/arch/x86/kernel/apic/apic.c
@@ -61,12 +61,6 @@ unsigned int boot_cpu_physical_apicid =

/*
* The highest APIC ID seen during enumeration.
- *
- * This determines the messaging protocol we can use: if all APIC IDs
- * are in the 0 ... 7 range, then we can use logical addressing which
- * has some performance advantages (better broadcasting).
- *
- * If there's an APIC ID above 8, we use physical addressing.
*/
unsigned int max_physical_apicid;

@@ -1898,14 +1892,7 @@ void __cpuinit generic_processor_info(in
max_physical_apicid = apicid;

#ifdef CONFIG_X86_32
- /*
- * Would be preferable to switch to bigsmp when CONFIG_HOTPLUG_CPU=y
- * but we need to work other dependencies like SMP_SUSPEND etc
- * before this can be done without some confusion.
- * if (CPU_HOTPLUG_ENABLED || num_processors > 8)
- * - Ashok Raj <ashok.raj@intel.com>
- */
- if (max_physical_apicid >= 8) {
+ if (num_processors > 8) {
switch (boot_cpu_data.x86_vendor) {
case X86_VENDOR_INTEL:
if (!APIC_XAPIC(version)) {
Index: tip/arch/x86/kernel/apic/probe_64.c
===================================================================
--- tip.orig/arch/x86/kernel/apic/probe_64.c
+++ tip/arch/x86/kernel/apic/probe_64.c
@@ -64,15 +64,13 @@ void __init default_setup_apic_routing(v
apic = &apic_x2apic_phys;
else
apic = &apic_x2apic_cluster;
- printk(KERN_INFO "Setting APIC routing to %s\n", apic->name);
}
#endif

- if (apic == &apic_flat) {
- if (max_physical_apicid >= 8)
+ if (apic == &apic_flat && num_processors > 8)
apic = &apic_physflat;
- printk(KERN_INFO "Setting APIC routing to %s\n", apic->name);
- }
+
+ printk(KERN_INFO "Setting APIC routing to %s\n", apic->name);

if (is_vsmp_box()) {
/* need to update phys_pkg_id */



\
 
 \ /
  Last update: 2010-01-18 21:29    [W:0.051 / U:0.424 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site