lkml.org 
[lkml]   [2010]   [Jan]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRe: [PATCH 04/64] pata_amd: remove bogus code from timing_setup()
Date
On Monday 18 January 2010 06:50:37 pm Alan Cox wrote:
> On Mon, 18 Jan 2010 18:14:20 +0100
> Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> wrote:
>
> > From: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
> > Subject: [PATCH] pata_amd: remove bogus code from timing_setup()
> >
> > DMA modes don't have 8-bit timings.

s/timings/data timings/ [ though it should be obvious from the context ]

> If you are in a DMA based mode then you have 8bit timings for writes to
> the non data registers. You can get an 8bit timed access to the other
> drive even in DMA mode.

Sorry but this confuses taskfile timings (which are always PIO mode based
timings) with data timings (the removed code deals with the latter only)..

also please refer to ata_timings[] in drivers/ata/libata-core.c
(columns 3, 4 and 5 are the ones to look at):

static const struct ata_timing ata_timing[] = {
/* { XFER_PIO_SLOW, 120, 290, 240, 960, 290, 240, 0, 960, 0 }, */
{ XFER_PIO_0, 70, 290, 240, 600, 165, 150, 0, 600, 0 },
{ XFER_PIO_1, 50, 290, 93, 383, 125, 100, 0, 383, 0 },
{ XFER_PIO_2, 30, 290, 40, 330, 100, 90, 0, 240, 0 },
{ XFER_PIO_3, 30, 80, 70, 180, 80, 70, 0, 180, 0 },
{ XFER_PIO_4, 25, 70, 25, 120, 70, 25, 0, 120, 0 },
{ XFER_PIO_5, 15, 65, 25, 100, 65, 25, 0, 100, 0 },
{ XFER_PIO_6, 10, 55, 20, 80, 55, 20, 0, 80, 0 },

{ XFER_SW_DMA_0, 120, 0, 0, 0, 480, 480, 50, 960, 0 },
{ XFER_SW_DMA_1, 90, 0, 0, 0, 240, 240, 30, 480, 0 },
{ XFER_SW_DMA_2, 60, 0, 0, 0, 120, 120, 20, 240, 0 },

{ XFER_MW_DMA_0, 60, 0, 0, 0, 215, 215, 20, 480, 0 },
{ XFER_MW_DMA_1, 45, 0, 0, 0, 80, 50, 5, 150, 0 },
{ XFER_MW_DMA_2, 25, 0, 0, 0, 70, 25, 5, 120, 0 },
{ XFER_MW_DMA_3, 25, 0, 0, 0, 65, 25, 5, 100, 0 },
{ XFER_MW_DMA_4, 25, 0, 0, 0, 55, 20, 5, 80, 0 },

/* { XFER_UDMA_SLOW, 0, 0, 0, 0, 0, 0, 0, 0, 150 }, */
{ XFER_UDMA_0, 0, 0, 0, 0, 0, 0, 0, 0, 120 },
{ XFER_UDMA_1, 0, 0, 0, 0, 0, 0, 0, 0, 80 },
{ XFER_UDMA_2, 0, 0, 0, 0, 0, 0, 0, 0, 60 },
{ XFER_UDMA_3, 0, 0, 0, 0, 0, 0, 0, 0, 45 },
{ XFER_UDMA_4, 0, 0, 0, 0, 0, 0, 0, 0, 30 },
{ XFER_UDMA_5, 0, 0, 0, 0, 0, 0, 0, 0, 20 },
{ XFER_UDMA_6, 0, 0, 0, 0, 0, 0, 0, 0, 15 },

{ 0xFF }
};

--
Bartlomiej Zolnierkiewicz


\
 
 \ /
  Last update: 2010-01-18 19:27    [W:0.207 / U:0.096 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site