lkml.org 
[lkml]   [2009]   [Sep]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
Subject[BUG 2.6.30+] e100 sometimes causes oops during resume
Hello,

I'm getting following oops sometimes during resume on my Thinkpad T21
(where "sometimes" means about 10/1 good/bad ratio):

ifconfig: page allocation failure. order:5, mode:0x8020
Pid: 26450, comm: ifconfig Not tainted 2.6.31-rc9-revert #13
Call Trace:
[<c015c1cc>] ? __alloc_pages_nodemask+0x402/0x444
[<c0104de7>] ? dma_generic_alloc_coherent+0x4a/0xab
[<c0104d9d>] ? dma_generic_alloc_coherent+0x0/0xab
[<c0298f5b>] ? e100_alloc_cbs+0xc7/0x174
[<c0299fea>] ? e100_up+0x1b/0xf5
[<c029a0db>] ? e100_open+0x17/0x41
[<c02fb0bf>] ? dev_open+0x8f/0xc5
[<c02fa879>] ? dev_change_flags+0xa2/0x155
[<c03305b6>] ? devinet_ioctl+0x22a/0x51c
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c02ee61e>] ? sock_ioctl+0x1c0/0x1e4
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c017ef06>] ? vfs_ioctl+0x16/0x4a
[<c017f7cd>] ? do_vfs_ioctl+0x48a/0x4c1
[<c0167e07>] ? handle_mm_fault+0x1e0/0x42c
[<c034bd9c>] ? do_page_fault+0x2ce/0x2e4
[<c017f830>] ? sys_ioctl+0x2c/0x42
[<c0102748>] ? sysenter_do_call+0x12/0x26
Mem-Info:
DMA per-cpu:
CPU 0: hi: 0, btch: 1 usd: 0
Normal per-cpu:
CPU 0: hi: 90, btch: 15 usd: 9
Active_anon:10268 active_file:11642 inactive_anon:24589
inactive_file:13029 unevictable:0 dirty:9 writeback:0 unstable:0
free:894 slab:2149 mapped:3962 pagetables:449 bounce:0
DMA free:1076kB min:124kB low:152kB high:184kB active_anon:936kB inactive_anon:3388kB active_file:2776kB inactive_file:3080kB unevictable:0kB present:15868kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 238 238
Normal free:2500kB min:1908kB low:2384kB high:2860kB active_anon:40136kB inactive_anon:94968kB active_file:43792kB inactive_file:49036kB unevictable:0kB present:243776kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0
DMA: 1*4kB 0*8kB 3*16kB 2*32kB 1*64kB 1*128kB 1*256kB 1*512kB 0*1024kB 0*2048kB 0*4096kB = 1076kB
Normal: 415*4kB 65*8kB 18*16kB 1*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2500kB
29934 total pagecache pages
5112 pages in swap cache
Swap cache stats: add 104796, delete 99684, find 78817/93038
Free swap = 457116kB
Total swap = 514040kB
65520 pages RAM
1667 pages reserved
11094 pages shared
56751 pages non-shared
ifconfig: page allocation failure. order:5, mode:0x8020
Pid: 26450, comm: ifconfig Not tainted 2.6.31-rc9-revert #13
Call Trace:
[<c015c1cc>] ? __alloc_pages_nodemask+0x402/0x444
[<c0104de7>] ? dma_generic_alloc_coherent+0x4a/0xab
[<c0104d9d>] ? dma_generic_alloc_coherent+0x0/0xab
[<c0298f5b>] ? e100_alloc_cbs+0xc7/0x174
[<c0299fea>] ? e100_up+0x1b/0xf5
[<c029a0db>] ? e100_open+0x17/0x41
[<c02fb0bf>] ? dev_open+0x8f/0xc5
[<c02fa879>] ? dev_change_flags+0xa2/0x155
[<c03305b6>] ? devinet_ioctl+0x22a/0x51c
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c02ee61e>] ? sock_ioctl+0x1c0/0x1e4
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c017ef06>] ? vfs_ioctl+0x16/0x4a
[<c017f7cd>] ? do_vfs_ioctl+0x48a/0x4c1
[<c016a217>] ? unmap_region+0xa2/0xd1
[<c016a289>] ? remove_vma+0x43/0x48
[<c016ad7a>] ? do_munmap+0x20e/0x228
[<c017f830>] ? sys_ioctl+0x2c/0x42
[<c0102748>] ? sysenter_do_call+0x12/0x26
Mem-Info:
DMA per-cpu:
CPU 0: hi: 0, btch: 1 usd: 0
Normal per-cpu:
CPU 0: hi: 90, btch: 15 usd: 8
Active_anon:10316 active_file:11612 inactive_anon:24605
inactive_file:13025 unevictable:0 dirty:9 writeback:66 unstable:0
free:864 slab:2149 mapped:3985 pagetables:462 bounce:0
DMA free:1076kB min:124kB low:152kB high:184kB active_anon:936kB inactive_anon:3388kB active_file:2776kB inactive_file:3080kB unevictable:0kB present:15868kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 238 238
Normal free:2380kB min:1908kB low:2384kB high:2860kB active_anon:40328kB inactive_anon:95032kB active_file:43672kB inactive_file:49020kB unevictable:0kB present:243776kB pages_scanned:128 all_unreclaimable? no
lowmem_reserve[]: 0 0 0
DMA: 1*4kB 0*8kB 3*16kB 2*32kB 1*64kB 1*128kB 1*256kB 1*512kB 0*1024kB 0*2048kB 0*4096kB = 1076kB
Normal: 415*4kB 60*8kB 15*16kB 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2380kB
29960 total pagecache pages
5172 pages in swap cache
Swap cache stats: add 104862, delete 99690, find 78819/93040
Free swap = 456856kB
Total swap = 514040kB
65520 pages RAM
1667 pages reserved
11419 pages shared
56744 pages non-shared


This is caused by ifup scripts that try to bring interface up after
resume. When I do so manually it doesn't produce error. System seems
to behave normally despite that error.

This is on 2.6.31-rc9 (with unrelated patch reverted), 2.6.31-rc8
shown similiar behaviour. Neither 2.6.31 nor Linus' HEAD seems to
address this issue.


Hardware:

0:03.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 09)
Subsystem: Intel Corporation EtherExpress PRO/100+ MiniPCI
Flags: bus master, medium devsel, latency 66, IRQ 11
Memory at e8120000 (32-bit, non-prefetchable) [size=4K]
I/O ports at 1800 [size=64]
Memory at e8100000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at 20100000 [disabled] [size=1M]
Capabilities: [dc] Power Management version 2
Kernel driver in use: e100
Full dmesg follows, including successful suspend-resume and oops (at
end) of unsuccessful one.


Linux version 2.6.31-rc9-revert (karol@wagner) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #13 Mon Sep 7 21:16:17 CEST 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fffec00 (ACPI data)
BIOS-e820: 000000000fffec00 - 0000000010000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
DMI 2.3 present.
last_pfn = 0xfff0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
00000-9FFFF write-back
A0000-BFFFF uncachable
C0000-CBFFF write-protect
CC000-DFFFF uncachable
E0000-FFFFF write-protect
MTRR variable ranges enabled:
0 base 000000000 mask FF0000000 write-back
1 disabled
2 disabled
3 disabled
4 disabled
5 disabled
6 disabled
7 disabled
initial memory mapped : 0 - 00800000
init_memory_mapping: 0000000000000000-000000000fff0000
0000000000 - 0000400000 page 4k
0000400000 - 000fc00000 page 2M
000fc00000 - 000fff0000 page 4k
kernel direct mapping tables up to fff0000 @ 7000-c000
ACPI: RSDP 000f7120 00014 (v00 PTLTD )
ACPI: RSDT 0fff4c5d 0002C (v01 PTLTD RSDT 06041160 LTP 00000000)
ACPI: FACP 0fffeb65 00074 (v01 IBM TP-T21 06041160 00000000)
ACPI: DSDT 0fff4c89 09EDC (v01 IBM TP-T21 06041160 MSFT 0100000C)
ACPI: FACS 0ffff000 00040
ACPI: BOOT 0fffebd9 00027 (v01 PTLTD $SBFTBL$ 06041160 LTP 00000001)
255MB LOWMEM available.
mapped low ram: 0 - 0fff0000
low ram: 0 - 0fff0000
node 0 low ram: 00000000 - 0fff0000
node 0 bootmap 00001000 - 00003000
(6 early reservations) ==> bootmem [0000000000 - 000fff0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000100000 - 0000516940] TEXT DATA BSS ==> [0000100000 - 0000516940]
#2 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
#3 [0000517000 - 00005190d9] BRK ==> [0000517000 - 00005190d9]
#4 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000]
#5 [0000001000 - 0000003000] BOOTMAP ==> [0000001000 - 0000003000]
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x0000fff0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000000 -> 0x0000009f
0: 0x00000100 -> 0x0000fff0
On node 0 totalpages: 65423
free_area_init_node: node 0, pgdat c0458514, node_mem_map c1000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3967 pages, LIFO batch:0
Normal zone: 480 pages used for memmap
Normal zone: 60944 pages, LIFO batch:15
ACPI: PM-Timer IO Port: 0x1008
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 10000000 (gap: 10000000:eff80000)
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64911
Kernel command line: root=/dev/sda2 resume=/dev/sda1 ro
PID hash table entries: 1024 (order: 10, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
Memory: 255100k/262080k available (2359k kernel code, 6468k reserved, 1086k data, 256k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffe5000 - 0xfffff000 ( 104 kB)
vmalloc : 0xd07f0000 - 0xfffe3000 ( 759 MB)
lowmem : 0xc0000000 - 0xcfff0000 ( 255 MB)
.init : 0xc045e000 - 0xc049e000 ( 256 kB)
.data : 0xc034dc2b - 0xc045d720 (1086 kB)
.text : 0xc0100000 - 0xc034dc2b (2359 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:16
CPU 0 irqstacks, hard=c042b000 soft=c042c000
Fast TSC calibration using PIT
Detected 796.603 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 1593.20 BogoMIPS (lpj=3186412)
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
mce: CPU supports 5 MCE banks
Performance Counters:
no APIC, boot with the "lapic" boot parameter to force-enable it.
no hardware sampling interrupt available.
p6 PMU driver.
... version: 0
... bit width: 32
... generic counters: 2
... value mask: 00000000ffffffff
... max period: 000000007fffffff
... fixed-purpose counters: 0
... counter mask: 0000000000000003
CPU: Intel Pentium III (Coppermine) stepping 0a
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090521
ACPI: setting ELCR to 0200 (from 0800)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd94f, last bus=7
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x9, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: Power Resource [PSER] (off)
ACPI: Power Resource [PSIO] (on)
ACPI: ACPI Dock Station Driver: 3 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 10 32bit mmio: [0xf8000000-0xfbffffff]
pci 0000:00:02.0: reg 10 32bit mmio: [0x50000000-0x50000fff]
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.1: reg 10 32bit mmio: [0x50100000-0x50100fff]
pci 0000:00:02.1: supports D1 D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.1: PME# disabled
pci 0000:00:03.0: reg 10 32bit mmio: [0xe8120000-0xe8120fff]
pci 0000:00:03.0: reg 14 io port: [0x1800-0x183f]
pci 0000:00:03.0: reg 18 32bit mmio: [0xe8100000-0xe811ffff]
pci 0000:00:03.0: reg 30 32bit mmio: [0x000000-0x0fffff]
pci 0000:00:03.0: supports D1 D2
pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:03.1: reg 10 io port: [0x1840-0x1847]
pci 0000:00:03.1: reg 14 32bit mmio: [0xe8121000-0xe8121fff]
pci 0000:00:03.1: supports D1 D2
pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:03.1: PME# disabled
pci 0000:00:05.0: reg 10 32bit mmio: [0xe8122000-0xe8122fff]
pci 0000:00:05.0: reg 14 32bit mmio: [0xe8000000-0xe80fffff]
pci 0000:00:05.0: supports D1 D2
pci 0000:00:07.1: reg 20 io port: [0x1850-0x185f]
pci 0000:00:07.2: reg 20 io port: [0x1860-0x187f]
pci 0000:00:07.3: quirk: region 1000-103f claimed by PIIX4 ACPI
pci 0000:00:07.3: quirk: region 1040-104f claimed by PIIX4 SMB
pci 0000:00:07.3: PIIX4 devres C PIO at 15e8-15ef
pci 0000:00:07.3: PIIX4 devres I PIO at 03f0-03f7
pci 0000:00:07.3: PIIX4 devres J PIO at 002e-002f
pci 0000:01:00.0: reg 10 32bit mmio: [0xf0000000-0xf7ffffff]
pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x00ffff]
pci 0000:01:00.0: supports D1 D2
pci 0000:00:01.0: bridge 32bit mmio: [0xf0000000-0xf7ffffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:00: mem resource (0x0-0x9ffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xc0000-0xc3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xc4000-0xc7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xc8000-0xcbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xcc000-0xcffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xd0000-0xcffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xd4000-0xd3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xd8000-0xd7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xdc000-0xdbfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xe0000-0xe3fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xe4000-0xe7fff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xe8000-0xebfff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xec000-0xeffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp 00:00: mem resource (0xf0000-0xfffff) overlaps 0000:00:03.0 BAR 6 (0x0-0xfffff), disabling
pnp: PnP ACPI: found 15 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0x100000-0xfffffff could not be reserved
system 00:00: iomem range 0xfff80000-0xffffffff has been reserved
system 00:02: ioport range 0x1000-0x103f has been reserved
system 00:02: ioport range 0x1040-0x104f has been reserved
system 00:02: ioport range 0xfe00-0xfe0f has been reserved
system 00:09: ioport range 0x15e0-0x15ef has been reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0: IO window: disabled
pci 0000:00:01.0: MEM window: 0xf0000000-0xf7ffffff
pci 0000:00:01.0: PREFETCH window: 0x20000000-0x200fffff
pci 0000:00:02.0: CardBus bridge, secondary bus 0000:02
pci 0000:00:02.0: IO window: 0x001400-0x0014ff
pci 0000:00:02.0: IO window: 0x001c00-0x001cff
pci 0000:00:02.0: PREFETCH window: 0x10000000-0x13ffffff
pci 0000:00:02.0: MEM window: 0x14000000-0x17ffffff
pci 0000:00:02.1: CardBus bridge, secondary bus 0000:06
pci 0000:00:02.1: IO window: 0x002000-0x0020ff
pci 0000:00:02.1: IO window: 0x002400-0x0024ff
pci 0000:00:02.1: PREFETCH window: 0x18000000-0x1bffffff
pci 0000:00:02.1: MEM window: 0x1c000000-0x1fffffff
pci 0000:00:02.0: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
pci 0000:00:02.1: power state changed by ACPI to D0
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
pci 0000:00:02.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 1 mem: [0xf0000000-0xf7ffffff]
pci_bus 0000:01: resource 2 pref mem [0x20000000-0x200fffff]
pci_bus 0000:02: resource 0 io: [0x1400-0x14ff]
pci_bus 0000:02: resource 1 io: [0x1c00-0x1cff]
pci_bus 0000:02: resource 2 pref mem [0x10000000-0x13ffffff]
pci_bus 0000:02: resource 3 mem: [0x14000000-0x17ffffff]
pci_bus 0000:06: resource 0 io: [0x2000-0x20ff]
pci_bus 0000:06: resource 1 io: [0x2400-0x24ff]
pci_bus 0000:06: resource 2 pref mem [0x18000000-0x1bffffff]
pci_bus 0000:06: resource 3 mem: [0x1c000000-0x1fffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Simple Boot Flag at 0x35 set to 0x1
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ROMFS MTD (C) 2007 Red Hat, Inc.
msgmni has been set to 498
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:00.0: Limiting direct PCI/PCI transfers
pci 0000:01:00.0: Boot video device
savagefb 0000:01:00.0: power state changed by ACPI to D0
savagefb 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
savagefb: mapped io at d0880000
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
savagefb: mapped framebuffer at d0980000, pbase == f0000000
savagefb v0.4.0_2.6: 8064kB VRAM, using 800x600, 37.878kHz, 60Hz
Console: switching to colour frame buffer device 100x37
fb: S3 Savage/IX-MV frame buffer device
vga16fb: initializing
vga16fb: mapped to 0xc00a0000
fb1: VGA16 VGA frame buffer device
ACPI: AC Adapter [AC] (on-line)
input: Power Button as /class/input/input0
ACPI: Power Button [PWRF]
input: Lid Switch as /class/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button as /class/input/input2
ACPI: Sleep Button [SLPB]
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
processor LNXCPU:00: registered as cooling_device0
Switched to high resolution mode on CPU 0
ACPI: Processor [CPU0] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (44 C)
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 440BX Chipset
agpgart-intel 0000:00:00.0: AGP aperture is 64M @ 0xf8000000
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial 00:0c: activated
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
serial 0000:00:03.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
parport_pc 00:0d: reported by Plug and Play ACPI
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
ACPI: Battery Slot [BAT0] (battery present)
brd: module loaded
loop: module loaded
ata_piix 0000:00:07.1: version 2.13
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1850 irq 14
ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1858 irq 15
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:03.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
e100 0000:00:03.0: PME# disabled
e100: eth0: e100_probe: addr 0xe8120000, irq 11, MAC addr 00:10:a4:89:e8:84
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 242 bytes nvram
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
Advanced Linux Sound Architecture Driver Version 1.0.20.
input: AT Translated Set 2 keyboard as /class/input/input3
ALSA device list:
No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
ata1.00: ATA-7: SAMSUNG HM060HC, YJ100-19, max UDMA/100
ata1.00: 117231408 sectors, multi 16: LBA48
ata1.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA SAMSUNG HM060HC YJ10 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda:
sd 0:0:0:0: Attached scsi generic sg0 type 0
sda1 sda2 sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
Clocksource tsc unstable (delta = -117760284 ns)
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /class/input/input4
rtc_cmos 00:06: setting system clock to 2009-09-10 08:21:25 UTC (1252570885)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
Freeing unused kernel memory: 256k freed
uhci_hcd: USB Universal Host Controller Interface driver
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00001860
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31-rc9-revert uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
yenta_cardbus 0000:00:02.0: CardBus bridge found [1014:0130]
yenta_cardbus 0000:00:02.0: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:00:02.0: Routing CardBus interrupts to PCI
yenta_cardbus 0000:00:02.0: TI: mfunc 0x00001000, devctl 0x66
yenta_cardbus 0000:00:02.0: ISA IRQ mask 0x0438, PCI irq 11
yenta_cardbus 0000:00:02.0: Socket status: 30000006
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
ALSA sound/pci/cs46xx/cs46xx_lib.c:432: cs46xx: failure waiting for FIFO command to complete
input: PC Speaker as /class/input/input5
Non-volatile memory driver v1.3
thinkpad_acpi: ThinkPad ACPI Extras v0.23
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS KZET34WW (1.16 ), EC unknown
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi::standby
input: ThinkPad Extra Buttons as /class/input/input6
yenta_cardbus 0000:00:02.1: CardBus bridge found [1014:0130]
yenta_cardbus 0000:00:02.1: Using INTVAL to route CSC interrupts to PCI
yenta_cardbus 0000:00:02.1: Routing CardBus interrupts to PCI
yenta_cardbus 0000:00:02.1: TI: mfunc 0x00001000, devctl 0x66
yenta_cardbus 0000:00:02.1: ISA IRQ mask 0x0438, PCI irq 11
yenta_cardbus 0000:00:02.1: Socket status: 30000006
Adding 514040k swap on /dev/sda1. Priority:-1 extents:1 across:514040k
EXT3 FS on sda2, internal journal
fuse init (API version 7.12)
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
lp0: using parport0 (interrupt-driven).
lp0: console ready
ppdev: user-space parallel port driver
[drm] Initialized drm 1.1.0 20060810
eth0: no IPv6 routers present
[drm] Initialized savage 2.4.1 20050313 for 0000:01:00.0 on minor 0
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: New USB device found, idVendor=046d, idProduct=c050
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB-PS/2 Optical Mouse
usb 1-1: Manufacturer: Logitech
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: Logitech USB-PS/2 Optical Mouse as /class/input/input7
generic-usb 0003:046D:C050.0001: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1/input0
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
ACPI handle has no context!
e100 0000:00:03.0: PCI INT A disabled
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# disabled
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
ACPI handle has no context!
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
ALSA sound/pci/cs46xx/dsp_spos.c:1884: dsp_spos: SPIOWriteTask not responding
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.00 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.04 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
ACPI handle has no context!
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
ALSA sound/pci/cs46xx/dsp_spos.c:1884: dsp_spos: SPIOWriteTask not responding
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
ALSA sound/pci/cs46xx/cs46xx_lib.c:432: cs46xx: failure waiting for FIFO command to complete
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.02 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.06 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# disabled
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.00 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.06 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# disabled
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.02 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.05 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# disabled
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
udevd version 125 started
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.04 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.08 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# disabled
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.00 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# disabled
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
usb 1-1: reset low speed USB device using uhci_hcd and address 2
Restarting tasks ... done.
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
usb 1-1: USB disconnect, address 2
Sound Fusion CS46xx 0000:00:05.0: PCI INT A disabled
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.02 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.05 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
parport_pc 00:0d: disabled
serial 00:0c: disabled
savagefb 0000:01:00.0: power state changed by ACPI to D3
uhci_hcd 0000:00:07.2: PCI INT D disabled
ACPI handle has no context!
e100 0000:00:03.0: PME# enabled
ACPI: Preparing to enter system sleep state S3
Back to C!
ACPI: Waking up from system sleep state S3
pci 0000:00:01.0: restoring config space at offset 0x9 (was 0xfff0, writing 0x20002000)
pci 0000:00:01.0: restoring config space at offset 0x7 (was 0x2a000f0, writing 0x22a000f0)
e100 0000:00:03.0: restoring config space at offset 0x1 (was 0x2900013, writing 0x2900017)
savagefb 0000:01:00.0: power state changed by ACPI to D0
e100 0000:00:03.0: PME# disabled
pci 0000:00:05.0: PME# disabled
uhci_hcd 0000:00:07.2: PCI INT D -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
usb usb1: root hub lost power or was reset
savagefb: probed videoram: 8192k
savagefb: Detected current MCLK value of 83045 kHz
savagefb: 1024x768 TFT LCD panel detected and active
savagefb: Limiting video mode to 1024x768
serial 00:0c: activated
parport_pc 00:0d: activated
sd 0:0:0:0: [sda] Starting disk
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:42:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/03:0c:00:00:00:a0 filtered out
ata1.00: configured for UDMA/33
ata1.00: configured for UDMA/33
ata1: EH complete
Restarting tasks ... done.
Sound Fusion CS46xx 0000:00:05.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
ifconfig: page allocation failure. order:5, mode:0x8020
Pid: 26450, comm: ifconfig Not tainted 2.6.31-rc9-revert #13
Call Trace:
[<c015c1cc>] ? __alloc_pages_nodemask+0x402/0x444
[<c0104de7>] ? dma_generic_alloc_coherent+0x4a/0xab
[<c0104d9d>] ? dma_generic_alloc_coherent+0x0/0xab
[<c0298f5b>] ? e100_alloc_cbs+0xc7/0x174
[<c0299fea>] ? e100_up+0x1b/0xf5
[<c029a0db>] ? e100_open+0x17/0x41
[<c02fb0bf>] ? dev_open+0x8f/0xc5
[<c02fa879>] ? dev_change_flags+0xa2/0x155
[<c03305b6>] ? devinet_ioctl+0x22a/0x51c
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c02ee61e>] ? sock_ioctl+0x1c0/0x1e4
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c017ef06>] ? vfs_ioctl+0x16/0x4a
[<c017f7cd>] ? do_vfs_ioctl+0x48a/0x4c1
[<c0167e07>] ? handle_mm_fault+0x1e0/0x42c
[<c034bd9c>] ? do_page_fault+0x2ce/0x2e4
[<c017f830>] ? sys_ioctl+0x2c/0x42
[<c0102748>] ? sysenter_do_call+0x12/0x26
Mem-Info:
DMA per-cpu:
CPU 0: hi: 0, btch: 1 usd: 0
Normal per-cpu:
CPU 0: hi: 90, btch: 15 usd: 9
Active_anon:10268 active_file:11642 inactive_anon:24589
inactive_file:13029 unevictable:0 dirty:9 writeback:0 unstable:0
free:894 slab:2149 mapped:3962 pagetables:449 bounce:0
DMA free:1076kB min:124kB low:152kB high:184kB active_anon:936kB inactive_anon:3388kB active_file:2776kB inactive_file:3080kB unevictable:0kB present:15868kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 238 238
Normal free:2500kB min:1908kB low:2384kB high:2860kB active_anon:40136kB inactive_anon:94968kB active_file:43792kB inactive_file:49036kB unevictable:0kB present:243776kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 0 0
DMA: 1*4kB 0*8kB 3*16kB 2*32kB 1*64kB 1*128kB 1*256kB 1*512kB 0*1024kB 0*2048kB 0*4096kB = 1076kB
Normal: 415*4kB 65*8kB 18*16kB 1*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2500kB
29934 total pagecache pages
5112 pages in swap cache
Swap cache stats: add 104796, delete 99684, find 78817/93038
Free swap = 457116kB
Total swap = 514040kB
65520 pages RAM
1667 pages reserved
11094 pages shared
56751 pages non-shared
ifconfig: page allocation failure. order:5, mode:0x8020
Pid: 26450, comm: ifconfig Not tainted 2.6.31-rc9-revert #13
Call Trace:
[<c015c1cc>] ? __alloc_pages_nodemask+0x402/0x444
[<c0104de7>] ? dma_generic_alloc_coherent+0x4a/0xab
[<c0104d9d>] ? dma_generic_alloc_coherent+0x0/0xab
[<c0298f5b>] ? e100_alloc_cbs+0xc7/0x174
[<c0299fea>] ? e100_up+0x1b/0xf5
[<c029a0db>] ? e100_open+0x17/0x41
[<c02fb0bf>] ? dev_open+0x8f/0xc5
[<c02fa879>] ? dev_change_flags+0xa2/0x155
[<c03305b6>] ? devinet_ioctl+0x22a/0x51c
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c02ee61e>] ? sock_ioctl+0x1c0/0x1e4
[<c02ee45e>] ? sock_ioctl+0x0/0x1e4
[<c017ef06>] ? vfs_ioctl+0x16/0x4a
[<c017f7cd>] ? do_vfs_ioctl+0x48a/0x4c1
[<c016a217>] ? unmap_region+0xa2/0xd1
[<c016a289>] ? remove_vma+0x43/0x48
[<c016ad7a>] ? do_munmap+0x20e/0x228
[<c017f830>] ? sys_ioctl+0x2c/0x42
[<c0102748>] ? sysenter_do_call+0x12/0x26
Mem-Info:
DMA per-cpu:
CPU 0: hi: 0, btch: 1 usd: 0
Normal per-cpu:
CPU 0: hi: 90, btch: 15 usd: 8
Active_anon:10316 active_file:11612 inactive_anon:24605
inactive_file:13025 unevictable:0 dirty:9 writeback:66 unstable:0
free:864 slab:2149 mapped:3985 pagetables:462 bounce:0
DMA free:1076kB min:124kB low:152kB high:184kB active_anon:936kB inactive_anon:3388kB active_file:2776kB inactive_file:3080kB unevictable:0kB present:15868kB pages_scanned:0 all_unreclaimable? no
lowmem_reserve[]: 0 238 238
Normal free:2380kB min:1908kB low:2384kB high:2860kB active_anon:40328kB inactive_anon:95032kB active_file:43672kB inactive_file:49020kB unevictable:0kB present:243776kB pages_scanned:128 all_unreclaimable? no
lowmem_reserve[]: 0 0 0
DMA: 1*4kB 0*8kB 3*16kB 2*32kB 1*64kB 1*128kB 1*256kB 1*512kB 0*1024kB 0*2048kB 0*4096kB = 1076kB
Normal: 415*4kB 60*8kB 15*16kB 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2380kB
29960 total pagecache pages
5172 pages in swap cache
Swap cache stats: add 104862, delete 99690, find 78819/93040
Free swap = 456856kB
Total swap = 514040kB
65520 pages RAM
1667 pages reserved
11419 pages shared
56744 pages non-shared
usb 1-1: new low speed USB device using uhci_hcd and address 3
usb 1-1: New USB device found, idVendor=046d, idProduct=c050
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: USB-PS/2 Optical Mouse
usb 1-1: Manufacturer: Logitech
usb 1-1: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /class/input/input8
generic-usb 0003:046D:C050.0002: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1/input0
e100 0000:00:03.0: firmware: using built-in firmware e100/d101s_ucode.bin
ADDRCONF(NETDEV_UP): eth0: link is not ready
e100: eth0 NIC Link is Up 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present


\
 
 \ /
  Last update: 2009-09-15 14:09    [from the cache]
©2003-2011 Jasper Spaans