lkml.org 
[lkml]   [2009]   [Jun]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    /
    From
    SubjectRe: 2.6.30: suspend-to-ram, second s2r wakes up immediately
    Date
    On Sunday 14 June 2009, Thomas Meyer wrote:
    > Am Sonntag, den 14.06.2009, 20:31 +0200 schrieb Frans Pop:
    > > Rafael J. Wysocki wrote:
    > >
    > > >> 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) (prog-if 20 [EHCI])
    > > >> Subsystem: Micro-Star International Co., Ltd. Device 7250
    > > >> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
    > > >> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    > > >> Latency: 0 (750ns min, 250ns max)
    > > >> Interrupt: pin B routed to IRQ 23
    > > >> Region 0: Memory at fe9fac00 (32-bit, non-prefetchable) [size=256]
    > > >> Capabilities: [44] Debug port: BAR=1 offset=0098
    > > >> Capabilities: [80] Power Management version 2
    > > >> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
    > > >> Status: D0 PME-Enable- DSel=0 DScale=0 PME+
    > > >> Kernel driver in use: ehci_hcd
    > > >
    > > > PME+ means that the USB EHCI controller will signal a PME as soon as it is
    > > > enabled, so if PME is enabled on the controller before suspend, it will
    > > > wake up the system.
    > > >
    > > > Please send a boot log.
    > >
    > > Was already included in the initial message...
    > >
    > > I wonder if this device could be the cause:
    > > [ 40.232873] wlan0: register 'rndis_wlan' at usb-0000:00:02.1-6.1,
    > > Wireless RNDIS device, BCM4320b based, 00:16:01:cf:56:29
    > > [ 40.232907] usbcore: registered new interface driver rndis_wlan
    > > [...]
    > > [ 41.705516] rndis_wlan 1-6.1:1.0: rndis media disconnect
    >
    > Good idea. I should have thought of this myself. No, it's not above
    > device. I just tested several constellations and it's seems to be my usb
    > mouse. when the mouse is unplug suspend to ram works reliably.
    >
    > how to fix the mouse's behaviour?

    In principle, you should be able to disable wake-up on the USB controllers.

    As for the mouse itself, I don't know. I'm not even sure if it's possible at
    all (CCing Jiri).

    Best,
    Rafael


    \
     
     \ /
      Last update: 2009-06-14 21:31    [W:0.045 / U:0.152 seconds]
    ©2003-2016 Jasper Spaans. hosted at Digital OceanAdvertise on this site