lkml.org 
[lkml]   [2009]   [Apr]   [10]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: READ CAPACITY (16) failing
On Wed, Apr 08, 2009 at 01:54:48PM -0600, Matthew Wilcox wrote:
> On Wed, Apr 08, 2009 at 02:43:57PM -0500, Mike Miller (OS Dev) wrote:
> > I'm working on the HP Smart Array SCSI driver (hpsa) and I'm seeing the
> > following failures:
> >
> > hpsa1: <0x3230> at PCI 0000:02:00.0 IRQ 76 using DAC
> > scsi4 : hpsa
> > scsi 4:0:0:0: Direct-Access HP LOGICAL VOLUME 5.20 PQ: 0 ANSI: 5
> > sd 4:0:0:0: Attached scsi generic sg4 type 0
> > sd 4:0:0:0: [sdd] READ CAPACITY(16) failed
> > sd 4:0:0:0: [sdd] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
> > sd 4:0:0:0: [sdd] Sense not available.
> > hpsa: cp ffff8800cf400000 has check condition: unknown type: Sense: 0x5,
> > ASC: 0x20, ASCQ: 0x0, Returning result: 0x2, cmd=[a0 00 00 00 00 00 00 00 10
> > 00]
>
> > The READ CAPACITY failures are what I'm concerned about. I can't seem to track
> > down why that's failing.
> > I've tried printing out the_result from sd but it's not printing out. I'm
> > assuming that anytime I load the driver it goes thru sd.
> >
> > if (the_result) {
> > sense_valid = scsi_sense_valid(&sshdr);
> > if (sense_valid &&
> > sshdr.sense_key == ILLEGAL_REQUEST &&
> > (sshdr.asc == 0x20 || sshdr.asc == 0x24) &&
> > sshdr.ascq == 0x00)
> > /* Invalid Command Operation Code or
> > * Invalid Field in CDB, just retry
> > * silently with RC10 */
> > return -EINVAL;
> > }
> > retries--;
> > } while (the_result && retries);
> > printk(KERN_WARNING "sd-mfm: the_result = %d\n", the_result);
>
> Probably the device you're testing against doesn't support RC16, which
> is fine. But for some reason, we're not getting valid sense data back
> from the device. Now, there's two responses to this that seem rational
> to me:
>
> - In sd.c, if the drive has returned no/invalid sense data, try RC10
> silently, just like the 0x20 / 0x24 ASC case.
> - Find out why this drive doesn't report valid sense data when attached
> to hpsa. I assume it does report valid sense data when attached to
> some other scsi card?

Me again,
The controllers do support RC16. After some more work it looks like RC16 is
never getting to the driver. I'm snooping the CDB's of all requests as well
as the completions from the driver and I never see a 0x9e. I do see the
RC10 (0x25) though, so I think my debug is right.

Why would I never the see the command in the driver?

-- mikem


\
 
 \ /
  Last update: 2009-04-10 21:35    [W:0.075 / U:0.284 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site