lkml.org 
[lkml]   [2009]   [Feb]   [24]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 1/6] Rewrite MSI-HOWTO
Matthew Wilcox wrote:
> From: Matthew Wilcox <willy@linux.intel.com>
>
> I didn't find the previous version very useful, so I rewrote it.
>
> Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
> ---
> Documentation/PCI/MSI-HOWTO.txt | 756 ++++++++++++++-------------------------
> 1 files changed, 275 insertions(+), 481 deletions(-)
>
> diff --git a/Documentation/PCI/MSI-HOWTO.txt b/Documentation/PCI/MSI-HOWTO.txt
> index 256defd..f1b9f09 100644
> --- a/Documentation/PCI/MSI-HOWTO.txt
> +++ b/Documentation/PCI/MSI-HOWTO.txt
> @@ -4,506 +4,300 @@
> Revised Feb 12, 2004 by Martine Silbermann
> email: Martine.Silbermann@hp.com
> Revised Jun 25, 2004 by Tom L Nguyen
> + Revised Jul 9, 2008 by Matthew Wilcox <willy@linux.intel.com>
> + Copyright 2003, 2008 Intel Corporation
>
> 1. About this guide
>

[deletia]

> -5.2.1 API pci_enable_msi
> +This guide describes the basics of Message Signaled Interrupts (MSIs),
> +the advantages of using MSI over traditional interrupt mechanisms, how
> +to change your driver to use MSI or MSI-X and some basic diagnostics to
> +try if a device doesn't support MSIs.
> +
> +
> +2. What are MSIs?
> +
> +A Message Signalled Interrupt is a write from the device to a special

Consistent spelling, please.

> +address which causes an interrupt to be received by the CPU.
> +
> +The MSI capability was first specified in PCI 2.2 and was later enhanced
> +in PCI 3.0 to allow each interrupt to be masked individually. The MSI-X
> +capability was also introduced with PCI 3.0. It supports more interrupts
> +per device than MSI and allows interrupts to be independently configured.
> +
> +Devices may support both MSI and MSI-X, but only one can be enabled at
> +a time.
> +
> +
> +3. Why use MSIs?
> +
> +There are three reasons why using MSIs can give an advantage over
> +traditional pin-based interrupts.
> +
> +Pin-based PCI interrupts are often shared amongst several devices.
> +To support this, the kernel must call each interrupt handler associated
> +with an interrupt which leads to reduced performance for the system as

with an interrupt,

> +a whole. MSIs are never shared, so this problem cannot arise.
> +
> +When a device writes data to memory, then raises a pin-based interrupt,
> +it is possible that the interrupt may arrive before all the data has
> +arrived in memory (this becomes more likely with devices behind PCI-PCI
> +bridges). In order to ensure that all the data has arrived in memory,
> +the interrupt handler must read a register on the device which raised
> +the interrupt. PCI transaction ordering rules require that all the data
> +arrives in memory before the value can be returned from the register.
> +Using MSIs avoids this problem as the interrupt-generating write cannot
> +pass the data writes, so by the time the interrupt is raised, the driver
> +knows that all the data has arrived in memory.
> +
> +PCI devices can only support a single pin-based interrupt per function.
> +Often drivers have to query the device to find out what event has
> +occurred, slowing down interrupt handling for the common case. With
> +MSIs, a device can support more interrupts, allowing each interrupt
> +to be specialised to a different purpose. One possible design gives
> +infrequent conditions (such as errors) their own interrupt which allows
> +the driver to handle the normal interrupt handling path more efficiently.
> +Other possible designs include giving one interrupt to each packet queue
> +in a network card or each port in a storage controller.
> +
> +
> +4. How to use MSIs
> +
> +PCI devices are initialised to use pin-based interrupts. The device
> +driver has to set up the device to use MSI or MSI-X. Not all machines
> +support MSIs correctly, and for those machines, the APIs described below
> +will simply fail and the device will continue to use pin-based interrupts.
> +
> +4.1 Include kernel support for MSIs
> +
> +To support MSI or MSI-X, the kernel must be built with the CONFIG_PCI_MSI
> +option enabled. This option is only available on some architectures,
> +and it may depend on some other options also being set. For example,
> +on x86, you must also enable X86_UP_APIC or SMP in order to see the
> +CONFIG_PCI_MSI option.
> +
> +4.2 Using MSI
> +
> +Most of the hard work is done for the driver in the PCI layer. It simply
> +has to request that the PCI layer set up the MSI capability for this
> +device.
> +
> +4.2.1 pci_enable_msi
>
> int pci_enable_msi(struct pci_dev *dev)
>

[deletia]

> +A successful call will allocate ONE interrupt to the device, regardless
> +of how many MSIs the device supports. The device will be switched from
> +pin-based interrupt mode to MSI mode. The dev->irq number is changed
> +to a new number which represents the message signaled interrupt.
> +This function should be called before the driver calls request_irq()
> +since enabling MSIs disables the pin-based IRQ and the driver will not
> +receive interrupts on the old interrupt.
>
> -5.2.2 API pci_disable_msi
> +4.2.2 pci_disable_msi

[deletia]

> +This function should be used to undo the effect of pci_enable_msi().
> +Calling it restores dev->irq to the pin-based interrupt number and frees
> +the previously allocated message signaled interrupt(s). The interrupt
> +may subsequently be assigned to another device, so drivers should not
> +cache the value of dev->irq.
>
> -This API enables a device driver to request the PCI subsystem
> -to enable MSI-X messages on its hardware device. Depending on
> -the availability of PCI vectors resources, the PCI subsystem enables
> -either all or none of the requested vectors.
> +A device driver must always call free_irq() on the interrupt(s)
> +for which it has called request_irq() before calling this function.
> +Failure to do so will result in a BUG_ON(), the device will be left with
> +MSI enabled and will leak its vector.
>
> -Argument 'dev' points to the device (pci_dev) structure.
> +4.3 Using MSI-X
>
> -Argument 'entries' is a pointer to an array of msix_entry structs.
> -The number of entries is indicated in argument 'nvec'.
> -struct msix_entry is defined in /driver/pci/msi.h:
> +The MSI-X capability is much more flexible than the MSI capability.
> +It supports up to 2048 interrupts, each of which can be separately
> +assigned. To support this flexibility, drivers must use an array of
> +`struct msix_entry':
>
> struct msix_entry {
> u16 vector; /* kernel uses to write alloc vector */
> u16 entry; /* driver uses to specify entry */
> };
>

[deletia]

> +This allows for the device to use these interrupts in a sparse fashion;
> +for example it could use interrupts 3 and 1027 and allocate only a
> +two-element array. The driver is expected to fill in the 'entry' value
> +in each element of the array to indicate which entries it wants the kernel
> +to assign interrupts for. It is invalid to fill in two entries with the
> +same number.
> +
> +4.3.1 pci_enable_msix
> +
> +int pci_enable_msix(struct pci_dev *dev, struct msix_entry *entries, int nvec)
> +
> +Calling this function asks the PCI subsystem to allocate 'nvec' MSIs.
> +The 'entries' argument is a pointer to an array of msix_entry structs
> +which should be at least 'nvec' entries in size. On success, the
> +function will return 0 and the device will have been switched into
> +MSI-X interrupt mode. The 'vector' elements in each entry will have
> +been filled in with the interrupt number. The driver should then call
> +request_irq() for each 'vector' that it decides to use.
> +
> +If this function returns a negative number, it indicates an error and
> +the driver should not attempt to allocate any more MSI-X interrupts for
> +this device. If it returns a positive number, it indicates the maximum
> +number of interrupt vectors that could have been allocated.
> +
> +This function, in contrast with pci_enable_msi(), does not adjust
> +dev->irq. The device will not generate interrupts for this interrupt
> +number once MSI-X is enabled. The device driver is responsible for
> +keeping track of the interrupts assigned to the MSI-X vectors so it can
> +free them again later.
> +
> +Device drivers should normally call this function once per device
> +during the initialization phase.

Consistent isation/ization (or ised/ized), please.

> +
> +4.3.2 pci_disable_msix
>
> void pci_disable_msix(struct pci_dev *dev)
>

[deletia]

> +This API should be used to undo the effect of pci_enable_msix(). It frees
> +the previously allocated message signaled interrupts. The interrupts may
> +subsequently be assigned to another device, so drivers should not cache
> +the value of the 'vector' elements over a call to pci_disable_msix().
> +
> +A device driver must always call free_irq() on the interrupt(s)
> +for which it has called request_irq() before calling this function.
> +Failure to do so will result in a BUG_ON(), the device will be left with
> +MSI enabled and will leak its vector.
> +
> +4.3.3 The MSI-X Table
> +
> +The MSI-X capability specifies a BAR and offset within that BAR for the
> +MSI-X Table. This address is mapped by the PCI subsystem, and should not
> +be accessed directly by the device driver. If the driver wishes to
> +mask or unmask an interrupt, it should call disable_irq() / enable_irq().
> +
> +4.4 Handling devices implementing both MSI and MSI-X capabilities
> +
> +If a device implements both MSI and MSI-X capabilities, it can
> +run in either MSI mode or MSI-X mode but not both simultaneously.
> +This is a requirement of the PCI spec, and it is enforced by the
> +PCI layer. Calling pci_enable_msi() when MSI-X is already enabled or
> +pci_enable_msix() when MSI is already enabled will result in an error.
> +If a device driver wishes to switch between MSI and MSI-X at runtime,
> +it must first quiesce the device, then switch it back to pin-interrupt
> +mode, before calling pci_enable_msi() or pci_enable_msix() and resuming
> +operation. This is not expected to be a common operation but may be
> +useful for debugging or testing during development.
> +
> +4.5 Considerations when using MSIs
> +
> +4.5.1 Choosing between MSI-X and MSI
> +
> +If your device supports both MSI-X and MSI capabilities, you should use
> +the MSI-X facilities in preference to the MSI facilities. As mentioned
> +above, MSI-X supports any number of interrupts between 1 and 2048.
> +In constrast, MSI is restricted to a maximum of 32 interrupts (and
> +must be a power of two). In addition, the MSI interrupt vectors must
> +be allocated consecutively, so the system may not be able to allocate
> +as many vectors for MSI as it could for MSI-X. On some platforms, MSI
> +interrupts must all be targetted at the same set of CPUs whereas MSI-X
> +interrupts can all be targetted at different CPUs.
> +
> +4.5.2 Spinlocks
> +
> +Most device drivers have a per-device spinlock which is taken in the
> +interrupt handler. With pin-based interrupts or a single MSI, it is not
> +necessary to disable interrupts (Linux guarantees the same interrupt will
> +not be re-entered). If a device uses multiple interrupts, the driver
> +must disable interrupts while the lock is held. If the device sends
> +a different interrupt, the driver will deadlock trying to recursively
> +acquire the spinlock.
> +
> +There are two solutions. The first is to take the
> +lock with spin_lock_irqsave() or spin_lock_irq() (see
> +Documentation/DocBook/kernel-locking). The second is to specify
> +IRQF_DISABLED to request_irq() so that the kernel runs the entire
> +interrupt routine with interrupts disabled.
> +
> +If your MSI interrupt routine does not hold the lock for the whole time
> +it is running, the first solution may be best. The second solution is
> +normally preferred as it avoids making two transitions from interrupt
> +disabled to enabled and back again.
> +
> +4.6 How to tell whether MSI/MSI-X is enabled on a device
> +
> +Using lspci -v (as root) will show some devices with "Message Signalled

Oh gosh, does lspci misspell it?

> +Interrupts" and others with "MSI-X". Each of these capabilities have an

Each ..................... has an

> +'Enable' flag which will be followed with either "+" (enabled) or "-"
> +(disabled).
> +
> +
> +5. MSI quirks
> +
> +Several PCI chipsets or devices are known not to support MSIs.
> +The PCI stack provides three ways to disable MSIs:
> +
> +1. globally
> +2. on all devices behind a specific bridge
> +3. on a single device
> +
> +5.1. Disabling MSIs globally
> +
> +Some host chipsets simply don't support MSIs properly. If we're
> +lucky, the manufacturer knows this and has indicated it in the ACPI
> +FADT table. In this case, Linux will automatically disable MSIs.
> +Some boards don't include this information in the table and so we have
> +to detect them ourselves. The complete list of these is found near the
> +quirk_disable_all_msi() function in drivers/pci/quirks.c.
> +
> +If you have a board which has problems with MSIs, you can pass pci=nomsi
> +on the kernel command line to disable MSIs on all devices. It would be
> +in your best interests to report the problem to linux-pci@vger.kernel.org
> +including a full lspci -v so we can add the quirks to the kernel.

I would say "lspci -v" ...

> +
> +5.2. Disabling MSIs below a bridge
> +
> +Some PCI bridges are not able to route MSIs between busses properly.
> +In this case, MSIs must be disabled on all devices behind the bridge.
> +
> +Some bridges allow you to enable MSIs by changing some bits in their
> +PCI configuration space (especially the Hypertransport chipsets such
> +as the nVidia nForce and Serverworks HT2000). As with host chipsets,
> +Linux mostly knows about them and automatically enables MSIs if it can.
> +If you have a bridge which Linux doesn't yet know about, you can enable
> +MSIs in configuration space using whatever method you know works, then
> +enable MSIs on that bridge by doing:
> +
> + echo 1 > /sys/bus/pci/devices/$bridge/msi_bus
> +
> +where $bridge is the PCI address of the bridge you've enabled (eg
> +0000:00:0e.0).
> +
> +To disable MSIs, echo 0 instead of 1. Changing this value should be
> +done with caution as it can break interrupt handling for all devices
> +below this bridge.
> +
> +Again, please notify linux-pci@vger.kernel.org of any bridges that need
> +special handling.
> +
> +5.3. Disabling MSIs on a single device
> +
> +Some devices are known to have faulty MSI implementations. Usually this
> +is handled in the individual device driver but occasionally it's necessary
> +to handle this with a quirk. Some drivers have an option to disable MSIs;
> +this is deprecated.
> +
> +5.4. Finding why MSIs are disabled on a device
> +
> +From the above three sections, you can see that there are many reasons
> +why MSIs may not be enabled for a given device. Your first step should
> +be to examine your dmesg carefully to determine whether MSIs are enabled
> +for your machine. You should also check your .config to be sure you
> +have enabled CONFIG_PCI_MSI.
> +
> +Then, lspci -t gives the list of bridges above a device. Reading

"lspci -t"

> +/sys/bus/pci/devices/*/msi_bus will tell you whether MSI are enabled (1)
> +or disabled (0). If 0 is found in any of the msi_bus files belonging
> +to bridges between the PCI root and the device, MSIs are disabled.
> +
> +It is also worth checking whether the device driver supports MSIs.
> +

Unneeded ending blank line (nit).

--
~Randy


\
 
 \ /
  Last update: 2009-02-24 21:01    [W:0.154 / U:0.936 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site