lkml.org 
[lkml]   [2009]   [Dec]   [22]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: Asus eeepc 1008HA suspend issue and mac80211 suspend corner case
On Tue, Dec 22, 2009 at 08:20:55AM -0800, Luis Rodriguez wrote:
> On Tue, Dec 22, 2009 at 07:50:05AM -0800, Luis Rodriguez wrote:
> > On Mon, Dec 21, 2009 at 08:39:17PM -0800, Sujith Manoharan wrote:
> > > Luis Rodriguez wrote:
> > > > That log can be found here:
> > > >
> > > > http://bombadil.infradead.org/~mcgrof/logs/2.6.31-with-2.6.32-wireless/irq-disabled.txt
> > >
> > > Thanks for the log.
> > > It's a bug in ath9k, related to PowerSave.
> > >
> > > Can you test this patch ?
> > >
> > > diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
> > > index 3f5b887..419c382 100644
> > > --- a/drivers/net/wireless/ath/ath9k/main.c
> > > +++ b/drivers/net/wireless/ath/ath9k/main.c
> > > @@ -2504,6 +2504,9 @@ static void ath9k_stop(struct ieee80211_hw *hw)
> > > return; /* another wiphy still in use */
> > > }
> > >
> > > + /* Ensure HW is awake when we try to shut it down. */
> > > + ath9k_ps_wakeup(sc);
> > > +
> > > if (ah->btcoex_hw.enabled) {
> > > ath9k_hw_btcoex_disable(ah);
> > > if (ah->btcoex_hw.scheme == ATH_BTCOEX_CFG_3WIRE)
> > > @@ -2524,8 +2527,10 @@ static void ath9k_stop(struct ieee80211_hw *hw)
> > > /* disable HAL and put h/w to sleep */
> > > ath9k_hw_disable(ah);
> > > ath9k_hw_configpcipowersave(ah, 1, 1);
> > > - ath9k_setpower(sc, ATH9K_PM_FULL_SLEEP);
> > > + ath9k_ps_restore(sc);
> > >
> > > + /* Finally, put the chip in FULL SLEEP mode */
> > > + ath9k_setpower(sc, ATH9K_PM_FULL_SLEEP);
> > > sc->sc_flags |= SC_OP_INVALID;
> > >
> > > mutex_unlock(&sc->mutex);
> >
> >
> > Thanks for the patch, doesn't cure it though. Below is the log
> > with debug=0xa00 (CONFIG | PS), you can see some successes prior to
> > the failure.
>
> Here's the new log with 0x601, with a few pm-suspend successes above.

Let me massage this a little:

Here is one success:

> [ 249.543348] ath9k: NETWORK SLEEP -> AWAKE
> [ 249.549393] ath9k: AWAKE -> NETWORK SLEEP
> [ 249.577650] PM: Syncing filesystems ...
> [ 249.645775] ath9k: NETWORK SLEEP -> AWAKE
> [ 249.651822] ath9k: AWAKE -> NETWORK SLEEP
> [ 249.677281] done.
> [ 249.677291] PM: Preparing system for mem sleep
> [ 249.748159] ath9k: NETWORK SLEEP -> AWAKE
> [ 249.754256] ath9k: AWAKE -> NETWORK SLEEP
> [ 249.765132] ath9k: NETWORK SLEEP -> AWAKE

Device is awake prior to sending Tx BA.

> [ 249.824923] Freezing user space processes ... (elapsed 0.00 seconds) done.
> [ 249.826762] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
> [ 249.826830] PM: Entering mem sleep
> [ 249.826853] Suspending console(s) (use no_console_suspend to debug)
> [ 249.832057] Tx BA session stop requested for 00:22:6b:56:fd:e8 tid 0
> [ 249.832077] Stopping Tx BA session for 00:22:6b:56:fd:e8 tid 0
> [ 249.832110] Rx BA session stop requested for 00:22:6b:56:fd:e8 tid 0
> [ 249.832130] Tx BA session stop requested for 00:22:6b:56:fd:e8 tid 6
> [ 249.832141] Stopping Tx BA session for 00:22:6b:56:fd:e8 tid 6
> [ 249.832166] ath9k: Detach Interface
> [ 249.834435] ath9k: AWAKE -> FULL-SLEEP
> [ 249.834446] ath9k: Driver halt
> [ 249.858079] sd 0:0:0:0: [sda] Synchronizing SCSI cache
> [ 249.858457] sd 0:0:0:0: [sda] Stopping disk
> [ 250.781437] ath9k 0000:01:00.0: PCI INT A disabled

> [ 251.087088] Back to C!

> [ 252.038696] ath9k 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 254.521068] ath9k: Starting driver with initial channel: 2437 MHz
> [ 254.522086] ath9k: FULL-SLEEP -> AWAKE
> [ 254.533094] ath9k: ah->misc_mode 0x4
> [ 254.535214] ath9k: Attach a VIF of type: 2
> [ 254.535248] ath9k: Set channel: 2437 MHz
> [ 254.535252] ath9k: tx chmask: 1, rx chmask: 1
> [ 254.535373] ath9k: (2437 MHz) -> (2437 MHz), chanwidth: 1
> [ 254.541929] ath9k: ah->misc_mode 0x4
> [ 254.544052] ath9k: Set HW RX filter: 0x607
> [ 254.544058] ath9k: RX filter 0x0 bssid 00:22:6b:56:fd:e8 aid 0x0
> [ 254.544065] ath9k: BSS Changed PREAMBLE 1
> [ 254.544068] ath9k: BSS Changed CTS PROT 0
> [ 254.544072] ath9k: BSS Changed ASSOC 1
> [ 254.544076] ath9k: Bss Info ASSOC 1, bssid: 00:22:6b:56:fd:e8
> [ 254.546454] PM: Finishing wakeup.
> [ 254.546458] Restarting tasks ... done.
> [ 254.589051] Open BA session requested for 00:22:6b:56:fd:e8 tid 0
> [ 254.589095] activated addBA response timer on tid 0
> [ 254.615144] Rx A-MPDU request on tid 0 result 0
> [ 254.717357] switched off addBA timer for tid 0
> [ 254.717366] Aggregation is on for tid 0
> [ 254.718297] switched off addBA timer for tid 0

Then this is the failure suspend:

> [ 270.574054] ath9k: NETWORK SLEEP -> AWAKE
> [ 270.582421] ath9k: AWAKE -> NETWORK SLEEP
> [ 270.676431] ath9k: NETWORK SLEEP -> AWAKE
> [ 270.682643] ath9k: AWAKE -> NETWORK SLEEP
> [ 270.778860] ath9k: NETWORK SLEEP -> AWAKE
> [ 270.989686] ath9k: AWAKE -> NETWORK SLEEP
> [ 271.049041] ath9k: NETWORK SLEEP -> AWAKE
> [ 271.304833] PM: Syncing filesystems ... done.
> [ 271.307636] PM: Preparing system for mem sleep
> [ 271.399307] ath9k: AWAKE -> NETWORK SLEEP

Below the device seems to go to sleep prior to sending the Tx BA, but I could have
sworn this happens in another successfull suspend before.

> [ 271.448580] Freezing user space processes ... (elapsed 0.00 seconds) done.
> [ 271.450215] Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
> [ 271.450296] PM: Entering mem sleep
> [ 271.450321] Suspending console(s) (use no_console_suspend to debug)
> [ 271.456054] Tx BA session stop requested for 00:22:6b:56:fd:e8 tid 0
> [ 271.456073] Stopping Tx BA session for 00:22:6b:56:fd:e8 tid 0
> [ 271.456112] Rx BA session stop requested for 00:22:6b:56:fd:e8 tid 0
> [ 271.456141] ath9k: Detach Interface
> [ 271.456161] ath9k: NETWORK SLEEP -> AWAKE
> [ 271.458525] ath9k: AWAKE -> NETWORK SLEEP
> [ 271.458533] ath9k: NETWORK SLEEP -> FULL-SLEEP
> [ 271.458544] ath9k:
> [ 271.458547] ath9k: Driver halt
> [ 271.458552] FULL-SLEEP -> AWAKE

And we leave it awake prior to suspend, hrm.

> [ 271.485081] sd 0:0:0:0: [sda] Synchronizing SCSI cache
> [ 271.485444] sd 0:0:0:0: [sda] Stopping disk
> [ 272.348209] ath9k 0000:01:00.0: PCI INT A disabled

> [ 272.552139] Back to C!

> [ 273.522696] ath9k 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
> [ 275.742070] ath9k: Starting driver with initial channel: 2437 MHz
> [ 275.891791] ath9k: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
> [ 275.891799] ath9k: RTC stuck in MAC reset

AT this point hardware is already completely unresonsive.

> [ 275.891803] ath9k: Chip reset failed
> [ 275.891807] ath9k: Unable to reset hardware; reset status -22 (freq 2437 MHz)
> [ 275.891827] ath9k: Attach a VIF of type: 2
> [ 275.891867] ath9k: Set channel: 2437 MHz
> [ 275.891873] ath9k: tx chmask: 1, rx chmask: 1
> [ 275.891880] ath9k: Unable to set channel
> [ 275.891894] ath9k: Set HW RX filter: 0x2707
> [ 275.891901] ath9k: RX filter 0x0 bssid 00:22:6b:56:fd:e8 aid 0x0
> [ 275.891910] ath9k: BSS Changed PREAMBLE 1
> [ 275.891915] ath9k: BSS Changed CTS PROT 0
> [ 275.891919] ath9k: BSS Changed ASSOC 1
> [ 275.891924] ath9k: Bss Info ASSOC 1, bssid: 00:22:6b:56:fd:e8
> [ 275.894481] PM: Finishing wakeup.
> [ 275.894486] Restarting tasks ... done.
> [ 276.835592] irq 18: nobody cared (try booting with the "irqpoll" option)
> [ 276.835609] Pid: 1710, comm: Xorg Not tainted 2.6.31.4-intel-menlow #14
> [ 276.835616] Call Trace:
> [ 276.835636] [<c105ca3e>] __report_bad_irq+0x2e/0x6f
> [ 276.835646] [<c105cb74>] note_interrupt+0xf5/0x14d
> [ 276.835656] [<c105d0a4>] handle_fasteoi_irq+0x7d/0x9b
> [ 276.835668] [<c10048c1>] handle_irq+0x3b/0x46
> [ 276.835677] [<c1004103>] do_IRQ+0x41/0x95
> [ 276.835687] [<c1003189>] common_interrupt+0x29/0x30
> [ 276.835693] handlers:
> [ 276.835698] [<f89a3d03>] (ath_isr+0x0/0x12f [ath9k])
> [ 276.835739] Disabling IRQ #18

Luis


\
 
 \ /
  Last update: 2009-12-22 17:57    [W:0.295 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site